RFC3107: Carrying Label Information in BGP-4

Download in PDF format Download in text format

Obsoleted By:  RFC8277





Network Working Group                                         Y. Rekhter
Request for Comments: 3107                              Juniper Networks
Category: Standards Track                                       E. Rosen
                                                     Cisco Systems, Inc.
                                                                May 2001


                  Carrying Label Information in BGP-4

Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2001).  All Rights Reserved.

Abstract

   This document specifies the way in which the label mapping
   information for a particular route is piggybacked in the same Border
   Gateway Protocol (BGP) Update message that is used to distribute the
   route itself.  When BGP is used to distribute a particular route, it
   can be also be used to distribute a Multiprotocol Label Switching
   (MPLS) label which is mapped to that route.

Table of Contents

    1      Specification of Requirements  ..........................   2
    2      Overview  ...............................................   2
    3      Carrying Label Mapping Information  .....................   3
    4      Advertising Multiple Routes to a Destination  ...........   4
    5      Capability Advertisement  ...............................   4
    6      When the BGP Peers are not Directly Adjacent  ...........   5
    7      Security Considerations  ................................   5
    8      Acknowledgments  ........................................   6
    9      References  .............................................   6
   10      Authors' Addresses  .....................................   7
   11      Full Copyright Statement  ...............................   8








Rekhter & Rosen             Standards Track                     [Page 1]

RFC 3107          Carrying Label Information in BGP-4           May 2001


1. Specification of Requirements

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119.

2. Overview

   When BGP is used to distribute a particular route, it can also be
   used to distribute an MPLS label that is mapped to that route [MPLS-
   ARCH].  This document specifies the way in which this is done.  The
   label mapping information for a particular route is piggybacked in
   the same BGP Update message that is used to distribute the route
   itself.

   This can be useful in the following situations:

      -  If two immediately adjacent Label Switched Routers (LSRs) are
         also BGP peers, then label distribution can be done without the
         need for any other label distribution protocol.

      -  Suppose one's network consists of two "classes" of LSR:
         exterior LSRs, which interface to other networks, and interior
         LSRs, which serve only to carry traffic between exterior LSRs.
         Suppose that the exterior LSRs are BGP speakers.  If the BGP
         speakers distribute MPLS labels to each other along with each
         route they distribute, then as long as the interior routers
         support MPLS, they need not receive any of the BGP routes from
         the BGP speakers.

         If exterior router A needs to send a packet to destination D,
         and A's BGP next hop for D is exterior router B, and B has
         mapped label L to D, then A first pushes L onto the packet's
         label stack.  A then consults its IGP to find the next hop to
         B, call it C.  If C has distributed to A an MPLS label for the
         route to B, A can push this label on the packet's label stack,
         and then send the packet to C.

   If a set of BGP speakers are exchanging routes via a Route Reflector
   [BGP-RR], then by piggybacking the label distribution on the route
   distribution, one is able to use the Route Reflector to distribute
   the labels as well.  This improves scalability quite significantly.
   Note that if the Route Reflector is not in the forwarding path, it
   need not even be capable of forwarding MPLS packets.

   Label distribution can be piggybacked in the BGP Update message by
   using the BGP-4 Multiprotocol Extensions attribute [RFC 2283].  The
   label is encoded into the NLRI field of the attribute, and the SAFI



Rekhter & Rosen             Standards Track                     [Page 2]

RFC 3107          Carrying Label Information in BGP-4           May 2001


   ("Subsequent Address Family Identifier") field is used to indicate
   that the NLRI contains a label.  A BGP speaker may not use BGP to
   send labels to a particular BGP peer unless that peer indicates,
   through BGP Capability Advertisement, that it can process Update
   messages with the specified SAFI field.

3. Carrying Label Mapping Information

   Label mapping information is carried as part of the Network Layer
   Reachability Information (NLRI) in the Multiprotocol Extensions
   attributes.  The AFI indicates, as usual, the address family of the
   associated route.  The fact that the NLRI contains a label is
   indicated by using SAFI value 4.

   The Network Layer Reachability information is encoded as one or more
   triples of the form <length, label, prefix>, whose fields are
   described below:

      +---------------------------+
      |   Length (1 octet)        |
      +---------------------------+
      |   Label (3 octets)        |
      +---------------------------+
      .............................
      +---------------------------+
      |   Prefix (variable)       |
      +---------------------------+

   The use and the meaning of these fields are as follows:

      a) Length:

         The Length field indicates the length in bits of the address
         prefix plus the label(s).

      b) Label:

         The Label field carries one or more labels (that corresponds to
         the stack of labels [MPLS-ENCAPS]).  Each label is encoded as 3
         octets, where the high-order 20 bits contain the label value,
         and the low order bit contains "Bottom of Stack" (as defined in
         [MPLS-ENCAPS]).

      c) Prefix:

         The Prefix field contains address prefixes followed by enough
         trailing bits to make the end of the field fall on an octet
         boundary.  Note that the value of trailing bits is irrelevant.



Rekhter & Rosen             Standards Track                     [Page 3]

RFC 3107          Carrying Label Information in BGP-4           May 2001


   The label(s) specified for a particular route (and associated with
   its address prefix) must be assigned by the LSR which is identified
   by the value of the Next Hop attribute of the route.

   When a BGP speaker redistributes a route, the label(s) assigned to
   that route must not be changed (except by omission), unless the
   speaker changes the value of the Next Hop attribute of the route.

   A BGP speaker can withdraw a previously advertised route (as well as
   the binding between this route and a label) by either (a) advertising
   a new route (and a label) with the same NLRI as the previously
   advertised route, or (b) listing the NLRI of the previously
   advertised route in the Withdrawn Routes field of an Update message.
   The label information carried (as part of NLRI) in the Withdrawn
   Routes field should be set to 0x800000.  (Of course, terminating the
   BGP session also withdraws all the previously advertised routes.)

4. Advertising Multiple Routes to a Destination

   A BGP speaker may maintain (and advertise to its peers) more than one
   route to a given destination, as long as each such route has its own
   label(s).

   The encoding described above allows a single BGP Update message to
   carry multiple routes, each with its own label(s).

   In the case where a BGP speaker advertises multiple routes to a
   destination, if a route is withdrawn, and a label(s) is specified at
   the time of withdrawal, only the corresponding route with the
   corresponding label is withdrawn.  If a route is withdrawn, and no
   label is specified at the time of withdrawal, then only the
   corresponding unlabeled route is withdrawn; the labeled routes are
   left in place.

5. Capability Advertisement

   A BGP speaker that uses Multiprotocol Extensions to carry label
   mapping information should use the Capabilities Optional Parameter,
   as defined in [BGP-CAP], to inform its peers about this capability.
   The MP_EXT Capability Code, as defined in [BGP-MP], is used to
   advertise the (AFI, SAFI) pairs available on a particular connection.

   A BGP speaker should not advertise this capability to another BGP
   speaker unless there is a Label Switched Path (LSP) between the two
   speakers.






Rekhter & Rosen             Standards Track                     [Page 4]

RFC 3107          Carrying Label Information in BGP-4           May 2001


   A BGP speaker that is capable of handling multiple routes to a
   destination (as described above) should use the Capabilities Optional
   Parameter, as defined in [BGP-CAP], to inform its peers about this
   capability.  The value of this capability is 4.

6. When the BGP Peers are not Directly Adjacent

   Consider the following LSR topology: A--B--C--D.  Suppose that D
   distributes a label L to A.  In this topology, A cannot simply push L
   onto a packet's label stack, and then send the resulting packet to B.
   D must be the only LSR that sees L at the top of the stack.  Before A
   sends the packet to B, it must push on another label, which was
   distributed by B.  B must replace this label with yet another label,
   which was distributed by C.  In other words, there must be an LSP
   between A and D.  If there is no such LSP, A cannot make use of label
   L.  This is true any time labels are distributed between non-adjacent
   LSRs, whether that distribution is done by BGP or by some other
   method.

   This document does NOT specify any procedure for ensuring in real
   time that label distribution between non-adjacent LSRs is done only
   when the appropriate MPLS infrastructure exists in the network or
   networks connecting the two LSRs.  Ensuring that the proper
   infrastructure exists is an issue for network management and
   operation.

7. Security Considerations

   When an LSR A is directly connected to an LSR B via a point-to-point
   interface, then when A receives packets over that interface, it knows
   that they come from B.  This makes it easy for A to discard any
   packets from B whose top labels are not among the labels that A
   distributed to B.  That is, A can easily ensure that B only uses
   those labels which it is entitled to use.  This technique can be used
   to prevent "label spoofing", i.e., the situation in which an LSR
   imposes a label which has not been properly distributed to it.

   The procedures discussed in this document would commonly be used when
   the label distribution peers are separated not merely by a point-to-
   point link, but by an MPLS network.  This means that when an LSR A
   processes a labeled packet, it really has no way to determine which
   other LSR B pushed on the top label.  Hence it cannot tell whether
   the label is one which B is entitled to use.  In fact, when Route
   Reflectors are in use, A may not even know the set of LSRs which
   receive its label mappings.  So the previous paragraph's technique
   for preventing label spoofing does not apply.





Rekhter & Rosen             Standards Track                     [Page 5]

RFC 3107          Carrying Label Information in BGP-4           May 2001


   It is possible though to use other techniques to avoid label spoofing
   problems.  If, for example, one never accepts labeled packets from
   the network's "external" interfaces, and all the BGP-distributed
   labels are advertised via IBGP, then there is no way for an untrusted
   router to put a labeled packet into the network.  One can generally
   assume that one's IBGP peers (or the IBGP peers of one's Route
   Reflector) will not attempt label spoofing, since they are all under
   the control of a single administration.

   This condition can actually be weakened significantly.  One doesn't
   need to refuse to accept all labeled packets from external
   interfaces.  One just needs to make sure that any labeled packet
   received on an external interface has a top label which was actually
   distributed out that interface.

   Then a label spoofing problem would only exist if there are both
   trusted and untrusted systems out the same interface.  One way to
   avoid this problem is simply to avoid this situation.

8. Acknowledgments

   Thanks to Ravi Chandra, Enke Chen, Srihari Ramachandra, Eric Gray and
   Liam Casey for their comments.

9. References

   [BGP-4]       Rekhter, Y. and T. Li, "A Border Gateway Protocol 4
                 (BGP-4)", RFC 1771, March 1995.

   [BGP-CAP]     Chandra, R. and J. Scudder, "Capabilities Advertisement
                 with BGP-4", RFC 2842, May 2000.

   [BGP-MP]      Bates, T., Rekhter, Y, Chandra, R. and D. Katz,
                 "Multiprotocol Extensions for BGP-4", RFC 2858, June
                 2000.

   [BGP-RR]      Bates, T. and R. Chandra, "BGP Route Reflection: An
                 alternative to full mesh IBGP", RFC 1966, June 1996.

   [MPLS-ARCH]   Rosen, E., Vishwanathan, A. and R. Callon,
                 "Multiprotocol Label Switching Architecture" RFC 3031,
                 January 2001.

   [MPLS-ENCAPS] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y.,
                 Farinacci, D., Li, T. and A. Conta, "MPLS Label Stack
                 Encoding", RFC 3032, January 2001.





Rekhter & Rosen             Standards Track                     [Page 6]

RFC 3107          Carrying Label Information in BGP-4           May 2001


10. Authors' Addresses

   Yakov Rekhter
   Juniper Networks
   1194 N. Mathilda Avenue
   Sunnyvale, CA 94089

   EMail: yakov@juniper.net


   Eric Rosen
   Cisco Systems, Inc.
   250 Apollo Drive
   Chelmsford, MA 01824

   EMail: erosen@cisco.com



































Rekhter & Rosen             Standards Track                     [Page 7]

RFC 3107          Carrying Label Information in BGP-4           May 2001


11.  Full Copyright Statement

   Copyright (C) The Internet Society (2001).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.



















Rekhter & Rosen             Standards Track                     [Page 8]