RFC7123: Security Implications of IPv6 on IPv4 Networks

Download in PDF format Download in text format






Internet Engineering Task Force (IETF)                           F. Gont
Request for Comments: 7123                          SI6 Networks/UTN-FRH
Category: Informational                                           W. Liu
ISSN: 2070-1721                                      Huawei Technologies
                                                           February 2014


             Security Implications of IPv6 on IPv4 Networks

Abstract

   This document discusses the security implications of native IPv6
   support and IPv6 transition/coexistence technologies on "IPv4-only"
   networks and describes possible mitigations for the aforementioned
   issues.

Status of This Memo

   This document is not an Internet Standards Track specification; it is
   published for informational purposes.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Not all documents
   approved by the IESG are a candidate for any level of Internet
   Standard; see Section 2 of RFC 5741.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc7123.

Copyright Notice

   Copyright (c) 2014 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.





Gont & Liu                    Informational                     [Page 1]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
   2.  Security Implications of Native IPv6 Support  . . . . . . . .   4
     2.1.  Filtering Native IPv6 Traffic . . . . . . . . . . . . . .   4
   3.  Security Implications of Tunneling Mechanisms . . . . . . . .   5
     3.1.  Filtering 6in4  . . . . . . . . . . . . . . . . . . . . .   6
     3.2.  Filtering 6over4  . . . . . . . . . . . . . . . . . . . .   7
     3.3.  Filtering 6rd . . . . . . . . . . . . . . . . . . . . . .   7
     3.4.  Filtering 6to4  . . . . . . . . . . . . . . . . . . . . .   8
     3.5.  Filtering ISATAP  . . . . . . . . . . . . . . . . . . . .   9
     3.6.  Filtering Teredo  . . . . . . . . . . . . . . . . . . . .   9
     3.7.  Filtering Tunnel Broker with Tunnel Setup Protocol (TSP)   11
     3.8.  Filtering AYIYA . . . . . . . . . . . . . . . . . . . . .  11
   4.  Additional Considerations when Filtering IPv6 Traffic . . . .  12
   5.  Security Considerations . . . . . . . . . . . . . . . . . . .  13
   6.  Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  13
   7.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  13
     7.1.  Normative References  . . . . . . . . . . . . . . . . . .  13
     7.2.  Informative References  . . . . . . . . . . . . . . . . .  14
   Appendix A.  Summary of Filtering Rules . . . . . . . . . . . . .  18

1.  Introduction

   Most general-purpose operating systems implement and enable native
   IPv6 [RFC2460] support and a number of transition/coexistence
   technologies by default.  Support of IPv6 by all nodes is intended to
   become best current practice [RFC6540].  Some enterprise networks
   might, however, choose to delay active use of IPv6.

   This document describes operational practices to prevent security
   exposure in enterprise networks resulting from unplanned use of IPv6
   on such networks.  This document is only applicable to enterprise
   networks: networks where the network operator is not providing a
   general-purpose internet, but rather a business-specific network.
   The solutions proposed here are not practical for home networks, nor
   are they appropriate for provider networks such as ISPs, mobile
   providers, WiFi hotspot providers, or any other public internet
   service.

   In scenarios in which IPv6-enabled devices are deployed on enterprise
   networks that are intended to be IPv4-only, native IPv6 support and/
   or IPv6 transition/coexistence technologies could be leveraged by
   local or remote attackers for a number of (illegitimate) purposes.
   For example,






Gont & Liu                    Informational                     [Page 2]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


   o  A Network Intrusion Detection System (NIDS) might be prepared to
      detect attack patterns for IPv4 traffic, but might be unable to
      detect the same attack patterns when a transition/coexistence
      technology is leveraged for that purpose.

   o  An IPv4 firewall might enforce a specific security policy in IPv4,
      but might be unable to enforce the same policy in IPv6.

   o  A NIDS or firewall might support both IPv4 and IPv6, but might not
      be configured to enforce on IPv6 traffic the same controls/
      policies it enforces on IPv4 traffic.

   o  Some transition/coexistence mechanisms could cause an internal
      host with otherwise limited IPv4 connectivity to become globally
      reachable over IPv6, therefore resulting in increased (and
      possibly unexpected) host exposure.

         NOTE: Some transition/coexistence mechanisms (notably Teredo)
         are designed to traverse Network Address Port Translation
         (NAPT) [RFC2663] devices, allowing incoming IPv6 connections
         from the Internet to hosts behind the organizational firewall
         or NAPT (which in many deployments provides a minimum level of
         protection by only allowing those instances of communication
         that have been initiated from the internal network).

   o  IPv6 support could, either inadvertently or as a result of a
      deliberate attack, result in Virtual Private Network (VPN) traffic
      leaks if IPv6-unaware VPN software is employed by dual-stacked
      hosts [VPN-LEAKS].

   In general, most of the aforementioned security implications can be
   mitigated by enforcing security controls on native IPv6 traffic and
   on IPv4-tunneled IPv6 traffic.  Among such controls, is the
   enforcement of filtering policies to block undesirable traffic.
   While IPv6 widespread/global IPv6 deployment has been slower than
   expected, it is nevertheless happening; and thus, filtering IPv6
   traffic (whether native or transition/coexistence) to mitigate IPv6
   security implications on IPv4 networks should (generally) only be
   considered as a temporary measure until IPv6 is deployed.

      NOTE: The aforementioned security controls should contemplate not
      only network-based solutions, but also host-based solutions (such
      as, e.g., personal firewalls).








Gont & Liu                    Informational                     [Page 3]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


2.  Security Implications of Native IPv6 Support

   Most popular operating systems include IPv6 support that is enabled
   by default.  This means that even if a network is expected to be
   IPv4-only, much of its infrastructure is nevertheless likely to be
   IPv6-enabled.  For example, hosts are likely to have at least link-
   local IPv6 connectivity, which might be exploited by attackers with
   access to the local network.

   Additionally, unless appropriate measures are taken, an attacker with
   access to an "IPv4-only" local network could impersonate a local
   router and cause local hosts to enable their 'non-link-local' IPv6
   connectivity (e.g., by sending Router Advertisement messages),
   possibly circumventing security controls that were enforced only on
   IPv4 communications.

      NOTE: [THC-IPV6] and [IPv6-Toolkit] include tools that implement
      this attack vector (along with many others).  [Waters2011]
      provides an example of how this could be achieved using publicly
      available tools.

   Native IPv6 support could also possibly lead to VPN-traffic leakages
   when hosts employ VPN software that, not only does not support IPv6,
   but does nothing about IPv6 traffic.  [VPN-LEAKS] describes this
   issue, along with possible mitigations.

   In general, networks should enforce on native IPv6 traffic the same
   security policies currently enforced on IPv4 traffic.  However, in
   those networks in which IPv6 has not yet been deployed and enforcing
   the aforementioned policies is deemed as infeasible, a network
   administrator might mitigate IPv6-based attack vectors by means of
   appropriate packet filtering.

2.1.  Filtering Native IPv6 Traffic

   Some layer-2 devices might have the ability to selectively filter
   packets based on the type of layer-2 payload.  When such
   functionality is available, IPv6 traffic could be blocked at those
   layer-2 devices by blocking, for example, Ethernet frames with the
   Protocol Type field set to 0x86dd [IANA-ETHER].  We note, however,
   that blocking IPv6 at layer-2 might create problems that are
   difficult to diagnose, inclusive of intentional or incidental use of
   link-local addressing (as in Multicast DNS/DNS-based Service
   Discovery [RFC6762] [RFC6763]); sites that enforce such a filtering
   policy should keep that possibility in mind when debugging the
   network.





Gont & Liu                    Informational                     [Page 4]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


   Attacks based on Stateless Address Autoconfiguration (SLAAC)
   [RFC3756] can be mitigated with technologies such as Router
   Advertisement Guard (RA-Guard) [RFC6105] [RA-GRD-IMP].  In a similar
   way, DHCPv6-based attacks can be mitigated with technologies such as
   DHCPv6-Shield [SHIELD].  However, both RA-Guard and DHCPv6-Shield are
   incapable of mitigating attack vectors that employ IPv6 link-local
   addresses, since configuration of such addresses does not rely on
   Router Advertisement messages or DHCPv6-server messages.

   Administrators considering the filtering of native IPv6 traffic at
   layer-3 devices are urged to pay attention to the general
   considerations for IPv6 traffic filtering discussed in Section 4.

      NOTE: If native IPv6 traffic is filtered at layer-2, local IPv6
      nodes would only get to configure IPv6 link-local addresses.

   In order to mitigate attacks based on native IPv6 traffic, IPv6
   security controls should be enforced on both IPv4 and IPv6 networks.
   The aforementioned controls might include: deploying IPv6-enabled
   NIDS, implementing IPv6 firewalling, etc.

      NOTE: In some very specific scenarios (e.g., military operations
      networks) in which only IPv4 service might be desired, a network
      administrator might want to disable IPv6 support in all the
      communicating devices.

3.  Security Implications of Tunneling Mechanisms

   Unless properly managed, tunneling mechanisms might result in
   negative security implications.  For example, they might increase
   host exposure, might be leveraged to evade security controls, might
   contain protocol-based vulnerabilities, and/or the corresponding code
   might contain bugs with security implications.

      NOTE: [RFC6169] describes the security implications of tunneling
      mechanisms in detail.  Of the plethora of tunneling mechanisms
      that have so far been standardized and widely implemented, the so-
      called "automatic tunneling" mechanisms (such as Teredo, Intra-
      Site Automatic Tunnel Addressing Protocol (ISATAP), and 6to4) are
      of particular interest from a security standpoint, since they
      might be employed without prior consent or action of the user or
      network administrator.

   Tunneling mechanisms should be a concern not only to network
   administrators that have consciously deployed them, but also to those
   who have not deployed them, as these mechanisms might be leveraged to
   bypass their security policies.




Gont & Liu                    Informational                     [Page 5]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


      NOTE: [CERT2009] contains some examples of how tunnels can be
      leveraged to bypass firewall rules.

   The aforementioned issues could be mitigated by applying the common
   security practice of only allowing traffic deemed as "necessary"
   (i.e., the so-called "default deny" policy).  Thus, when such policy
   is enforced, IPv6 transition/coexistence traffic would be blocked by
   default and would only be allowed as a result of an explicit
   decision.

      NOTE: It should be noted that this type of policy is usually
      enforced on a network that is the target of such traffic (such as
      an enterprise network).  IPv6 transition traffic should generally
      never be filtered, e.g., by an ISP when it is transit traffic.

   In those scenarios in which transition/coexistence traffic is meant
   to be blocked, it is highly recommended that, in addition to the
   enforcement of filtering policies at the organizational perimeter,
   the corresponding transition/coexistence mechanisms be disabled on
   each node connected to the organizational network.  This would not
   only prevent security breaches resulting from accidental use of these
   mechanisms, but would also disable this functionality altogether,
   possibly mitigating vulnerabilities that might be present in the host
   implementation of these transition/coexistence mechanisms.

   IPv6-in-IPv4 tunneling mechanisms (such as 6to4 or configured
   tunnels) can generally be blocked by dropping IPv4 packets that
   contain a Protocol field set to 41.  Security devices such as NIDS
   might also include signatures that detect such transition/coexistence
   traffic.

   Administrators considering the filtering of transition/coexistence
   traffic are urged to pay attention to the general considerations for
   IPv6 traffic filtering discussed in Section 4.

   We note that this document only covers standardized IPv6 tunneling
   mechanisms; it does not aim to cover non-standard tunneling
   mechanisms or tunneling based on IPsec [RFC4301] or on SSL/TLS
   [RFC5246] [RFC6101].

3.1.  Filtering 6in4

   Probably the most basic type of tunnel employed for connecting IPv6
   "islands" is the so-called "6in4", in which IPv6 packets are
   encapsulated within IPv4 packets.  These tunnels typically result
   from manual configuration at the two tunnel endpoints.





Gont & Liu                    Informational                     [Page 6]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


   6in4 tunnels can be blocked by blocking IPv4 packets with a Protocol
   field of 41.

3.2.  Filtering 6over4

   [RFC2529] specifies a mechanism known as 6over4 or 'IPv6 over IPv4'
   (or colloquially as 'virtual Ethernet'), which comprises a set of
   mechanisms and policies to allow isolated IPv6 hosts located on
   physical links with no directly connected IPv6 router to become fully
   functional IPv6 hosts by using an IPv4 domain that supports IPv4
   multicast as their virtual local link.

      NOTE: This transition technology has never been widely deployed
      because of the low level of deployment of multicast in most
      networks.

   6over4 encapsulates IPv6 packets in IPv4 packets with their Protocol
   field set to 41.  As a result, simply filtering all IPv4 packets that
   have a Protocol field equal to 41 will filter 6over4 (along with many
   other transition technologies).

   A more selective filtering could be enforced such that 6over4 traffic
   is filtered while other transition traffic is still allowed.  Such a
   filtering policy would block all IPv4 packets that have their
   Protocol field set to 41, and that have a Destination Address that
   belongs to the prefix 239.0.0.0/8.

   This filtering policy basically blocks 6over4 Neighbor Discovery
   traffic directed to multicast addresses, thus preventing SLAAC,
   address resolution, etc.  Additionally, it would prevent the 6over4
   multicast addresses from being leveraged for the purpose of network
   reconnaissance.

3.3.  Filtering 6rd

   6rd builds upon the mechanisms of 6to4 to enable the rapid deployment
   of IPv6 on IPv4 infrastructures, while avoiding some downsides of
   6to4.  Usage of 6rd was originally documented in [RFC5569], and the
   mechanism was generalized to other access technologies and formally
   standardized in [RFC5969].

   6rd can be blocked by blocking IPv4 packets with the Protocol field
   set to 41.








Gont & Liu                    Informational                     [Page 7]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


3.4.  Filtering 6to4

   6to4 [RFC3056] is an address assignment and router-to-router, host-
   to-router, and router-to-host automatic tunneling mechanism that is
   meant to provide IPv6 connectivity between IPv6 sites and hosts
   across the IPv4 Internet.

      NOTE: The security considerations for 6to4 are discussed in detail
      in [RFC3964].  [RFC6343] provides advice to network operators
      about 6to4 (some of which relates to security mitigations).

   As discussed in Section 3, all IPv6-in-IPv4 traffic, including 6to4,
   could be easily blocked by filtering IPv4 packets that contain their
   Protocol field set to 41.  This is the most effective way of
   filtering such traffic.

   If 6to4 traffic is meant to be filtered while other IPv6-in-IPv4
   traffic is allowed, then more finer-grained filtering rules could be
   applied.  For example, 6to4 traffic could be filtered by applying
   filtering rules such as:

   o  Filter outgoing IPv4 packets that have the Destination Address set
      to an address that belongs to the prefix 192.88.99.0/24.

   o  Filter incoming IPv4 packets that have the Source Address set to
      an address that belongs to the prefix 192.88.99.0/24.

         NOTE: These rules assume that the corresponding nodes employ
         the "Anycast Prefix for 6to4 Relay Routers" [RFC3068].  It has
         been suggested that 6to4 relays send their packets with their
         IPv4 Source Address set to 192.88.99.1.

   o  Filter outgoing IPv4 packets that have the Destination Address set
      to the IPv4 address of well-known 6to4 relays.

   o  Filter incoming IPv4 packets that have the Source Address set to
      the IPv4 address of well-known 6to4 relays.

      These last two filtering policies will generally be unnecessary,
      and possibly infeasible to enforce (given the number of potential
      6to4 relays, and the fact that many relays might remain unknown to
      the network administrator).  If anything, they should be applied
      with the additional requirement that such IPv4 packets have their
      Protocol field set to 41 to avoid the case where other services
      available at the same IPv4 address as a 6to4 relay are mistakenly
      made inaccessible.





Gont & Liu                    Informational                     [Page 8]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


   If the filtering device has capabilities to inspect the payload of
   IPv4 packets, then the following filtering rules could be enforced:

   o  Filter outgoing IPv4 packets that have their Protocol field set to
      41, and that have an IPv6 Source Address (embedded in the IPv4
      payload) that belongs to the prefix 2002::/16.

   o  Filter incoming IPv4 packets that have their Protocol field set to
      41, and that have an IPv6 Destination address (embedded in the
      IPv4 payload) that belongs to the prefix 2002::/16.

3.5.  Filtering ISATAP

   ISATAP [RFC5214] is an Intra-site tunneling protocol, and thus it is
   generally expected that such traffic will not traverse the
   organizational firewall of an IPv4-only network.  Nevertheless,
   ISATAP can be easily blocked by blocking IPv4 packets with a Protocol
   field of 41.

   The most popular operating system that includes an implementation of
   ISATAP in the default installation is Microsoft Windows.  Microsoft
   Windows obtains the ISATAP router address by resolving the domain
   name isatap.<localdomain> to DNS A resource records.  Additionally,
   it tries to learn the ISATAP router address by employing Link-Local
   Multicast Name Resolution (LLMNR) [RFC4795] to resolve the name
   "isatap".  As a result, blocking ISATAP by preventing hosts from
   successfully performing name resolution for the aforementioned names
   and/or by filtering packets with specific IPv4 destination addresses
   is both difficult and undesirable.

3.6.  Filtering Teredo

   Teredo [RFC4380] is an address assignment and automatic tunneling
   technology that provides IPv6 connectivity to dual-stack nodes that
   are behind one or more Network Address Port Translation (NAPT)
   [RFC2663] devices, by encapsulating IPv6 packets in IPv4-based UDP
   datagrams.  Teredo is meant to be a 'last-resort' IPv6 connectivity
   technology, to be used only when other technologies such as 6to4
   cannot be deployed (e.g., because the edge device has not been
   assigned a public IPv4 address).

   As noted in [RFC4380], in order for a Teredo client to configure its
   Teredo IPv6 address, it must contact a Teredo server through the
   Teredo service port (UDP port number 3544).

   To prevent the Teredo initialization process from succeeding, and
   hence prevent the use of Teredo, an organizational firewall could
   filter outgoing UDP packets with a Destination Port of 3544.



Gont & Liu                    Informational                     [Page 9]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


      NOTE: It is clear that such a filtering policy does not prevent an
      attacker from running its own Teredo server in the public
      Internet, using a non-standard UDP port for the Teredo service
      port (i.e., a port number other than 3544).

   If the filtering device has capabilities to inspect the payload of
   IPv4 packets, the following (additional) filtering policy could be
   enforced:

   o  Filter outgoing IPv4/UDP packets that embed an IPv6 packet with
      the "Version" field set to 6, and an IPv6 Source Address that
      belongs to the prefix 2001::/32.

   o  Filter incoming IPv4/UDP packets that embed an IPv6 packet with
      the "Version" field set to 6, and an IPv6 Destination Address that
      belongs to the prefix 2001::/32.

      NOTE: These two filtering rules could, at least in theory, result
      in false positives.  Additionally, they would generally require
      the filtering device to reassemble fragments prior to enforcing
      filtering rules, since the information required to enforce them
      might be missing in the received fragments (which should be
      expected if Teredo is being employed for malicious purposes).

   The most popular operating system that includes an implementation of
   Teredo in the default installation is Microsoft Windows.  Microsoft
   Windows obtains the Teredo server addresses (primary and secondary)
   by resolving the domain name teredo.ipv6.microsoft.com into DNS A
   records.  A network administrator might want to prevent Microsoft
   Windows hosts from obtaining Teredo service by filtering, at the
   organizational firewall, outgoing UDP datagrams (i.e., IPv4 packets
   with the Protocol field set to 17) that contain in the IPv4
   Destination Address any of the IPv4 addresses that the domain name
   teredo.ipv6.microsoft.com maps to (or the IPv4 address of any well-
   known Teredo server).  Additionally, the firewall would filter
   incoming UDP datagrams from any of the IPv4 addresses to which the
   domain names of well-known Teredo servers (such as
   teredo.ipv6.microsoft.com) resolve.

      NOTE: As these IPv4 addresses might change over time, an
      administrator should obtain these addresses when implementing the
      filtering policy, and should also be prepared to keep this list up
      to date.  The corresponding addresses can be easily obtained from
      a UNIX host by issuing the command 'dig teredo.ipv6.microsoft.com
      a' (without quotes), where dig(1) is a free-software tool (part of
      the "dnsutils" package) produced by the Internet Software
      Consortium (ISC).




Gont & Liu                    Informational                    [Page 10]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


   It should be noted that even with all these filtering policies in
   place, a node in the internal network might still be able to
   communicate with some Teredo clients.  That is, it could configure an
   IPv6 address itself (without even contacting a Teredo server), and it
   might send Teredo traffic to those peers for which intervention of
   the host's Teredo server is not required (e.g., Teredo clients behind
   a cone NAT).

3.7.  Filtering Tunnel Broker with Tunnel Setup Protocol (TSP)

   The tunnel broker model enables dynamic configuration of tunnels
   between a tunnel client and a tunnel server.  The tunnel broker
   provides a control channel for creating, deleting, or updating a
   tunnel between the tunnel client and the tunnel server.
   Additionally, the tunnel broker may register the user's IPv6 address
   and name in the DNS.  Once the tunnel is configured, data can flow
   between the tunnel client and the tunnel server.  [RFC3053] describes
   the tunnel broker model, while [RFC5572] specifies the Tunnel Setup
   Protocol (TSP), which can be used by clients to communicate with the
   Tunnel Broker.

   TSP can use either TCP or UDP as the transport protocol.  In both
   cases, TSP uses port number 3653, which has been assigned by the IANA
   for this purpose.  As a result, TSP (the Tunnel Broker control
   channel) can be blocked by blocking TCP and UDP packets originating
   from the local network and destined to UDP port 3653 or TCP port
   3653.  Additionally, the data channel can be blocked by blocking UDP
   packets originated from the local network and destined to UDP port
   3653, and IPv4 packets with a Protocol field set to 41.

3.8.  Filtering AYIYA

   AYIYA ("Anything In Anything") [AYIYA] allows the tunneling of
   packets across Network Address Port Translation (NAPT) [RFC2663]
   devices.  While the specification of this tunneling mechanism was
   never published as an RFC, it is nevertheless widely deployed
   [SixXS-stats].

   AYIYA can be blocked by blocking TCP and UDP packets originating from
   the local network and destined to UDP port 5072 or TCP port 5072.











Gont & Liu                    Informational                    [Page 11]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


4.  Additional Considerations when Filtering IPv6 Traffic

   IPv6 deployments in the Internet are continually increasing, and some
   hosts default to preferring IPv6 connectivity whenever it is
   available.  This is likely to cause IPv6-capable hosts to attempt to
   reach an ever-increasing number of popular destinations via IPv6,
   even if this IPv6 connectivity relies on a transition technology over
   an "IPv4-only" network.

   A large source of IPv6 brokenness today comes from nodes that believe
   that they have functional IPv6 connectivity, but the path to their
   destination fails somewhere upstream [Anderson2010] [Anderson2011]
   [Huston2010b] [Huston2012].  Upstream filtering of transition
   technologies or situations where a misconfigured node attempts to
   "provide" native IPv6 service on a given network without proper
   upstream IPv6 connectivity may result in hosts attempting to reach
   remote nodes via IPv6, and depending on the absence or presence and
   specific implementation details of "Happy Eyeballs" [RFC6555], there
   might be a non-trivial timeout period before the host falls back to
   IPv4 [Huston2010a] [Huston2012].

   For this reason, networks attempting to prevent IPv6 traffic from
   traversing their devices should consider configuring their local
   recursive DNS servers to respond to queries for AAAA DNS records with
   a DNS RCODE of 0 (NOERROR) [RFC1035] or to silently ignore such
   queries, and should even consider filtering AAAA records at the
   network ingress point to prevent the internal hosts from attempting
   their own DNS resolution.  This will ensure that hosts that are on an
   "IPv4-only" network will only receive DNS A records, and they will be
   unlikely to attempt to use (likely broken) IPv6 connectivity to reach
   their desired destinations.

   We note that in scenarios where DNSSEC [RFC4033] is deployed,
   stripping AAAA records from DNS responses would lead to DNS responses
   elicited by queries with the DO and CD bits set [RFC4035] to be
   considered invalid, and hence discarded.  This situation is similar
   to that of DNS64 [RFC6147] in the presence of DNSSEC and should be
   considered a drawback associated with this approach.

   Additionally, it should be noted that when filtering IPv6 traffic, it
   is good practice to signal the packet drop to the source node, such
   that it is able to react to the packet drop in a more appropriate and
   timely way.  For example, a firewall could signal the packet drop by
   means of an ICMPv6 error message (or TCP [RFC0793] RST segment if
   appropriate), such that the source node can, e.g., quickly react as
   described in [RFC5461].  For obvious reasons, if the traffic being





Gont & Liu                    Informational                    [Page 12]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


   filtered is IPv6 transition/coexistence traffic, the signaling packet
   should be sent by means of the corresponding IPv6 transition/
   coexistence technology.

5.  Security Considerations

   This document discusses the security implications of IPv6 on IPv4
   networks and describes a number of techniques to mitigate the
   aforementioned issues.  In general, the possible mitigations boil
   down to enforcing on native IPv6 and IPv6 transition/coexistence
   traffic the same security policies currently enforced for IPv4
   traffic and/or blocking the aforementioned traffic when it is deemed
   as undesirable.

6.  Acknowledgements

   The authors would like to thank Wes George, who contributed most of
   the text that comprises Section 4 of this document.

   The authors would like to thank (in alphabetical order) Ran Atkinson,
   Brian Carpenter, Stephen Farrell, Guillermo Gont, Joel Jaeggli, Panos
   Kampanakis, Warren Kumari, Ted Lemon, David Malone, Joseph Salowey,
   Arturo Servin, Donald Smith, Tina Tsou, and Eric Vyncke for providing
   valuable comments on earlier versions of this document.

   This document is based on the results of the project "Security
   Assessment of the Internet Protocol version 6 (IPv6)" [CPNI-IPv6],
   carried out by Fernando Gont on behalf of the UK Centre for the
   Protection of National Infrastructure (CPNI).  Fernando Gont would
   like to thank the UK CPNI for their continued support.

7.  References

7.1.  Normative References

   [RFC1035]  Mockapetris, P., "Domain names - implementation and
              specification", STD 13, RFC 1035, November 1987.

   [RFC2460]  Deering, S. and R. Hinden, "Internet Protocol, Version 6
              (IPv6) Specification", RFC 2460, December 1998.

   [RFC2529]  Carpenter, B. and C. Jung, "Transmission of IPv6 over IPv4
              Domains without Explicit Tunnels", RFC 2529, March 1999.

   [RFC3053]  Durand, A., Fasano, P., Guardini, I., and D. Lento, "IPv6
              Tunnel Broker", RFC 3053, January 2001.





Gont & Liu                    Informational                    [Page 13]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


   [RFC3056]  Carpenter, B. and K. Moore, "Connection of IPv6 Domains
              via IPv4 Clouds", RFC 3056, February 2001.

   [RFC3068]  Huitema, C., "An Anycast Prefix for 6to4 Relay Routers",
              RFC 3068, June 2001.

   [RFC4033]  Arends, R., Austein, R., Larson, M., Massey, D., and S.
              Rose, "DNS Security Introduction and Requirements", RFC
              4033, March 2005.

   [RFC4035]  Arends, R., Austein, R., Larson, M., Massey, D., and S.
              Rose, "Protocol Modifications for the DNS Security
              Extensions", RFC 4035, March 2005.

   [RFC4380]  Huitema, C., "Teredo: Tunneling IPv6 over UDP through
              Network Address Translations (NATs)", RFC 4380, February
              2006.

   [RFC4795]  Aboba, B., Thaler, D., and L. Esibov, "Link-local
              Multicast Name Resolution (LLMNR)", RFC 4795, January
              2007.

   [RFC5214]  Templin, F., Gleeson, T., and D. Thaler, "Intra-Site
              Automatic Tunnel Addressing Protocol (ISATAP)", RFC 5214,
              March 2008.

   [RFC5569]  Despres, R., "IPv6 Rapid Deployment on IPv4
              Infrastructures (6rd)", RFC 5569, January 2010.

   [RFC5969]  Townsley, W. and O. Troan, "IPv6 Rapid Deployment on IPv4
              Infrastructures (6rd) -- Protocol Specification", RFC
              5969, August 2010.

   [RFC5572]  Blanchet, M. and F. Parent, "IPv6 Tunnel Broker with the
              Tunnel Setup Protocol (TSP)", RFC 5572, February 2010.

   [RFC6147]  Bagnulo, M., Sullivan, A., Matthews, P., and I. van
              Beijnum, "DNS64: DNS Extensions for Network Address
              Translation from IPv6 Clients to IPv4 Servers", RFC 6147,
              April 2011.

7.2.  Informative References

   [RFC0793]  Postel, J., "Transmission Control Protocol", STD 7, RFC
              793, September 1981.






Gont & Liu                    Informational                    [Page 14]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


   [RFC2663]  Srisuresh, P. and M. Holdrege, "IP Network Address
              Translator (NAT) Terminology and Considerations", RFC
              2663, August 1999.

   [RFC3756]  Nikander, P., Kempf, J., and E. Nordmark, "IPv6 Neighbor
              Discovery (ND) Trust Models and Threats", RFC 3756, May
              2004.

   [RFC3964]  Savola, P. and C. Patel, "Security Considerations for
              6to4", RFC 3964, December 2004.

   [RFC4301]  Kent, S. and K. Seo, "Security Architecture for the
              Internet Protocol", RFC 4301, December 2005.

   [RFC5246]  Dierks, T. and E. Rescorla, "The Transport Layer Security
              (TLS) Protocol Version 1.2", RFC 5246, August 2008.

   [RFC5461]  Gont, F., "TCP's Reaction to Soft Errors", RFC 5461,
              February 2009.

   [RFC6101]  Freier, A., Karlton, P., and P. Kocher, "The Secure
              Sockets Layer (SSL) Protocol Version 3.0", RFC 6101,
              August 2011.

   [RFC6105]  Levy-Abegnoli, E., Van de Velde, G., Popoviciu, C., and J.
              Mohacsi, "IPv6 Router Advertisement Guard", RFC 6105,
              February 2011.

   [RFC6169]  Krishnan, S., Thaler, D., and J. Hoagland, "Security
              Concerns with IP Tunneling", RFC 6169, April 2011.

   [RFC6343]  Carpenter, B., "Advisory Guidelines for 6to4 Deployment",
              RFC 6343, August 2011.

   [RFC6540]  George, W., Donley, C., Liljenstolpe, C., and L. Howard,
              "IPv6 Support Required for All IP-Capable Nodes", BCP 177,
              RFC 6540, April 2012.

   [RFC6555]  Wing, D. and A. Yourtchenko, "Happy Eyeballs: Success with
              Dual-Stack Hosts", RFC 6555, April 2012.

   [RFC6762]  Cheshire, S. and M. Krochmal, "Multicast DNS", RFC 6762,
              February 2013.

   [RFC6763]  Cheshire, S. and M. Krochmal, "DNS-Based Service
              Discovery", RFC 6763, February 2013.





Gont & Liu                    Informational                    [Page 15]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


   [RA-GRD-IMP]
              Gont, F., "Implementation Advice for IPv6 Router
              Advertisement Guard (RA-Guard)", Work in Progress,
              November 2012.

   [VPN-LEAKS]
              Gont, F., "Virtual Private Network (VPN) traffic leakages
              in dual-stack hosts/ networks", Work in Progress, August
              2013.

   [SHIELD]   Gont, F., Liu, W., and G. Van de Velde, "DHCPv6-Shield:
              Protecting Against Rogue DHCPv6 Servers", Work in
              Progress, October 2013.

   [AYIYA]    Massar, J., "AYIYA: Anything In Anything", Work in
              Progress, July 2004.

   [IANA-ETHER]
              IANA, "Ethernet Numbers",
              <http://www.iana.org/assignments/ethernet-numbers>.

   [CERT2009] Giobbi, R., "Bypassing Firewalls with IPv6 Tunnels", CERT/
              CC Blog, April 2009, <http://www.cert.org/blogs/vuls/2009/
              04/bypassing_firewalls_with_ipv6.html>.

   [Huston2010a]
              Huston, G., "IPv6 Measurements", 2010,
              <http://www.potaroo.net/stats/1x1/>.

   [Huston2010b]
              Huston, G., "Flailing IPv6", The ISP Column: A monthly
              column on things Internet, December 2010,
              <http://www.potaroo.net/ispcol/2010-12/6to4fail.pdf>.

   [Huston2012]
              Huston, G., "Bemused Eyeballs: Tailoring Dual Stack
              Applications in a CGN Environment", The ISP Column: A
              monthly column on things Internet, May 2012,
              <http://www.potaroo.net/ispcol/2012-05/notquite.pdf>.

   [Anderson2010]
              Anderson, T., "Measuring and combating IPv6 brokenness",
              RIPE 61, Roma, November 2010,
              <http://ripe61.ripe.net/presentations/162-ripe61.pdf>.

   [Anderson2011]
              Anderson, T., "IPv6 dual-stack client loss in Norway",
              2011, <http://www.fud.no/ipv6/>.



Gont & Liu                    Informational                    [Page 16]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


   [CPNI-IPv6]
              Gont, F., "Security Assessment of the Internet Protocol
              version 6 (IPv6)", UK Centre for the Protection of
              National Infrastructure, (available on request), .

   [IPv6-Toolkit]
              SI6 Networks, "SI6 Networks' IPv6 Toolkit",
              <http://www.si6networks.com/tools/ipv6toolkit>.

   [THC-IPV6] The Hacker's Choice, "THC-IPV6 - attacking the IPV6
              protocol suite", December 2013,
              <http://www.thc.org/thc-ipv6/>.

   [Waters2011]
              Waters, A., "The SLAAC Attack - using IPv6 as a weapon
              against IPv4", April 2011,
              <http://wirewatcher.wordpress.com/2011/04/04/
              the-slaac-attack-using-ipv6-as-a-weapon-against-ipv4/>.

   [SixXS-stats]
              SixXS, , "SixXS - IPv6 Deployment & Tunnel Broker ::
              Statistics", 2013, <http://www.sixxs.net/misc/usage/>.





























Gont & Liu                    Informational                    [Page 17]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


Appendix A.  Summary of Filtering Rules

   +-------------+-----------------------------------------------------+
   |  Technology |                   Filtering rules                   |
   +-------------+-----------------------------------------------------+
   | Native IPv6 |                   EtherType 0x86DD                  |
   +-------------+-----------------------------------------------------+
   |     6in4    |                     IP proto 41                     |
   +-------------+-----------------------------------------------------+
   |    6over4   |                     IP proto 41                     |
   +-------------+-----------------------------------------------------+
   |     6rd     |                     IP proto 41                     |
   +-------------+-----------------------------------------------------+
   |     6to4    |                     IP proto 41                     |
   +-------------+-----------------------------------------------------+
   |    ISATAP   |                     IP proto 41                     |
   +-------------+-----------------------------------------------------+
   |    Teredo   |                  UDP Dest Port 3544                 |
   +-------------+-----------------------------------------------------+
   | TB with TSP |   (IP proto 41) || (UDP Dest Port 3653 || TCP Dest  |
   |             |                      Port 3653)                     |
   +-------------+-----------------------------------------------------+
   |    AYIYA    |       UDP Dest Port 5072 || TCP Dest Port 5072      |
   +-------------+-----------------------------------------------------+

                    Table 1: Summary of filtering rules

      NOTE: the table above describes general and simple filtering rules
      for blocking the corresponding traffic.  More finer-grained rules
      might be available in each of the corresponding sections of this
      document.




















Gont & Liu                    Informational                    [Page 18]

RFC 7123           Sec. Impl. of IPv6 on IPv4 Networks     February 2014


Authors' Addresses

   Fernando Gont
   SI6 Networks / UTN-FRH
   Evaristo Carriego 2644
   Haedo, Provincia de Buenos Aires  1706
   Argentina

   Phone: +54 11 4650 8472
   EMail: fgont@si6networks.com
   URI:   http://www.si6networks.com


   Will (Shucheng) Liu
   Huawei Technologies
   Bantian, Longgang District
   Shenzhen  518129
   P.R. China

   EMail: liushucheng@huawei.com































Gont & Liu                    Informational                    [Page 19]