RFC7867: RTP Control Protocol (RTCP) Extended Report (XR) Block for Loss Concealment Metrics for Video Applications

Download in PDF format Download in text format






Internet Engineering Task Force (IETF)                          R. Huang
Request for Comments: 7867                                        Huawei
Category: Standards Track                                      July 2016
ISSN: 2070-1721


         RTP Control Protocol (RTCP) Extended Report (XR) Block
          for Loss Concealment Metrics for Video Applications

Abstract

   This document defines a new RTP Control Protocol (RTCP) Extended
   Report (XR) block that allows the reporting of loss concealment
   metrics for video applications of RTP.

Status of This Memo

   This is an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of RFC 7841.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc7867.

Copyright Notice

   Copyright (c) 2016 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.








Huang                        Standards Track                    [Page 1]

RFC 7867              Video LC Metrics for RTCP XR             July 2016


Table of Contents

   1. Introduction ....................................................2
      1.1. RTCP and RTCP XR Reports ...................................3
      1.2. Performance Metrics Framework ..............................3
      1.3. Applicability ..............................................3
   2. Terminology .....................................................3
   3. Video Loss Concealment Methods ..................................3
   4. Video Loss Concealment Report Block .............................4
   5. SDP Signaling ...................................................8
      5.1. SDP rtcp-xr-attrib Attribute Extension .....................8
      5.2. Offer/Answer Usage .........................................9
   6. Security Considerations .........................................9
   7. IANA Considerations .............................................9
      7.1. New RTCP XR Block Type Value ...............................9
      7.2. New RTCP XR SDP Parameter ..................................9
      7.3. Contact Information for Registrations .....................10
   8. References .....................................................10
      8.1. Normative References ......................................10
      8.2. Informative References ....................................11
   Appendix A. Metrics Represented Using the Template from RFC 6390 ..12
   Acknowledgements ..................................................16
   Authors' Addresses ................................................16

1.  Introduction

   Multimedia applications often suffer from packet losses in IP
   networks.  In order to get a reasonable degree of quality when there
   is packet loss, it is necessary to have loss concealment mechanisms
   at the decoder.  Video loss concealment is a range of techniques to
   mask the effects of packet loss in video communications.

   In some applications, reporting the information of receivers applying
   video loss concealment could give monitors or senders useful
   information on the Quality of Experience (QoE) of the application.
   One example is no-reference video quality evaluation.  Video probes
   located upstream from the video endpoint or terminal may not see loss
   occurring between the probe and the endpoint, and also may not be
   fully aware of the specific loss concealment methods being
   dynamically applied by the video endpoint.  Evaluating error
   concealment is important in this circumstance to estimate the
   subjective impact of impairments.

   This document defines one new block type for video loss concealment
   to augment those defined in [RFC3611] and [RFC7294] for use in a
   range of RTP video applications.  The metrics defined in this
   document belong to the class of transport-related terminal metrics
   defined in [RFC6792].



Huang                        Standards Track                    [Page 2]

RFC 7867              Video LC Metrics for RTCP XR             July 2016


1.1.  RTCP and RTCP XR Reports

   The use of RTCP for reporting is defined in [RFC3550].  [RFC3611]
   defines an extensible structure for reporting using an RTCP Extended
   Report (XR).  This document defines a new Extended Report block that
   is used as defined in [RFC3550] and [RFC3611].

1.2.  Performance Metrics Framework

   The Performance Metrics Framework [RFC6390] provides guidance on the
   definition and specification of performance metrics.  The RTP
   monitoring framework [RFC6792] provides guidelines for the reporting
   block format using RTCP XR.  The XR block type described in this
   document is in accordance with the guidelines in [RFC6390] and
   [RFC6792].

1.3.  Applicability

   These metrics are applicable to video applications the video
   component of audio/video applications using RTP and applying packet
   loss concealment mechanisms that are incorporated into the receiving
   endpoint to mitigate the impact of network impairments on QoE.  For
   example, in an IPTV system, set-top boxes could use this RTCP XR
   block to report loss and loss concealment metrics to an IPTV
   management system to enable the service provider to monitor the
   quality of the IPTV service being delivered to end users.

2.  Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

3.  Video Loss Concealment Methods

   Video loss concealment mechanisms can be classified into 4 types as
   follows:

   a) Frame freeze

      The impaired video frame is not displayed; instead, the previously
      displayed frame is frozen for the duration of the loss event.

   b) Interframe extrapolation

      If an area of the video frame is damaged by loss, the same area
      from the previous frame(s) can be used to estimate what the
      missing pixels would have been.  This can work well in a scene



Huang                        Standards Track                    [Page 3]

RFC 7867              Video LC Metrics for RTCP XR             July 2016


      with no motion but can be very noticeable if there is significant
      movement from one frame to another.  Simple decoders can simply
      reuse the pixels that were in the missing area, while more complex
      decoders can try to use several frames to do a more complex
      extrapolation.  Another example of a sophisticated form of
      interframe repair is to estimate the motion of the damaged region
      based on the motion of surrounding regions, and use that to select
      what part of the previous frame to use for repair.  Some important
      frames, such as Instantaneous Decoding Refresh (IDR) frames, may
      not depend on any other frames and may be involved in a scene
      change.  Using the interframe extrapolation method to conceal the
      loss of these frames may not obtain a satisfactory result.

   c) Interpolation

      A decoder uses the undamaged pixels in the video frame to estimate
      what the missing block of pixels should have.

   d) Error-resilient encoding

      The sender encodes the message in a redundant way so that the
      receiver can correct errors using the redundant information.
      There are usually two kinds of error-resilient encoding: One is
      that the redundant data useful for error resiliency performed at
      the decoder can be embedded into the compressed image/video
      bitstream.  The other is encoding at the bitstream level, e.g.,
      Forward Error Correction (FEC).

   Usually, methods b, c, and d are deployed together to provide
   comprehensive loss concealment in complex decoders, while method a is
   relatively independent and may be applied in some simple decoders.
   Moreover, the frame-freeze method repairs video based on frames,
   while the other methods repair video based on fine-grained elements,
   such as macroblocks or bitstreams; this will cause the measurement
   metrics of frame-freeze and the other methods to be slightly
   different.  Thus, In this document, we differentiate between frame-
   freeze and the other 3 loss concealment mechanisms.

4.  Video Loss Concealment Report Block

   This block reports the video loss concealment metrics to complement
   the audio metrics defined in [RFC7294].  The report block MUST be
   sent in conjunction with the information from the Measurement
   Information Block [RFC6776].  Instances of this metric block refer by
   synchronization source (SSRC) to the separate auxiliary Measurement
   Information Block [RFC6776].  The Video Loss Concealment Report Block
   relies on the measurement period in the Measurement Information Block
   indicating the span of the report.  If the measurement period is not



Huang                        Standards Track                    [Page 4]

RFC 7867              Video LC Metrics for RTCP XR             July 2016


   received in the same compound RTCP packet as this metric block, this
   metric block MUST be discarded at the receiving side.  The metrics in
   this report block are based on measurements that are typically made
   at the time that a video frame is decoded and rendered for playout.

   The Video Loss Concealment Report Block has the following format:

    0               1               2               3
    0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    BT=34      | I | V |  RSV  |       Block Length            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         SSRC of Source                        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                       Impaired Duration                       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                      Concealed Duration                       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                  Mean Frame Freeze Duration (optional)        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    MIFP       |    MCFP       |     FFSC      |     Reserved  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      Figure 1: Format for the Video Loss Concealment Report Block

   Block Type (BT): 8 bits

      A Video Loss Concealment Report Block is identified by the
      constant 34.

   Interval Metric Flag (I): 2 bits

      This field indicates whether the reported metrics are interval,
      cumulative, or sampled metrics [RFC6792]:

         I=10: Interval Duration - the reported value applies to the
               most recent measurement interval duration between
               successive metrics reports.

         I=11: Cumulative Duration - the reported value applies to the
               accumulation period characteristic of cumulative
               measurements.

         I=01: Sampled Value - this value MUST NOT be used for this
               block type.

         I=00: Reserved.




Huang                        Standards Track                    [Page 5]

RFC 7867              Video LC Metrics for RTCP XR             July 2016


   Video Loss Concealment Method Type (V): 2 bits

      This field is used to identify the video loss concealment method
      type used at the receiver.  The value is defined as follows:

         V=10: Frame-freeze
         V=11: Other Loss Concealment Method
         V=01 and V=00: Reserved

      If frame-freeze and another loss concealment method are used
      together for the media stream, two report blocks (one with V=10
      for frame freeze and one with V=11 for the other loss concealment
      method) SHOULD be compounded together to report complete
      concealment information.

   RSV: 4 bits

      These bits are reserved for future use.  They MUST be set to zero
      by senders and ignored by receivers (see Section 4.2 of
      [RFC6709]).

   Block Length: 16 bits

      This field is in accordance with the definition in [RFC3611].  In
      this report block, it MUST be set to 5 when V=10 and set to 4 when
      V=11.  The block MUST be discarded if the block length is set to a
      different value.

   SSRC of Source: 32 bits

      As defined in Section 4.1 of [RFC3611].

   Impaired Duration: 32 bits

      The total duration, expressed in units of RTP timestamp from the
      sending side of the reporting block, of video impaired by
      transmission loss before applying any loss concealment methods.

      Two values are reserved: A value of 0xFFFFFFFE indicates out of
      range (that is, a measured value exceeding 0xFFFFFFFD), and a
      value of 0xFFFFFFFF indicates that the measurement is unavailable.

   Concealed Duration: 32 bits

      The total duration, expressed in units of RTP timestamp from the
      sending side of the reporting block, of concealed damaged video
      pictures on which the loss concealment method corresponding to the
      Video Loss Concealment Method Type is applied.



Huang                        Standards Track                    [Page 6]

RFC 7867              Video LC Metrics for RTCP XR             July 2016


      Two values are reserved: A value of 0xFFFFFFFE indicates out of
      range (that is, a measured value exceeding 0xFFFFFFFD), and a
      value of 0xFFFFFFFF indicates that the measurement is unavailable.

   Mean Frame-Freeze Duration: 32 bits

      Mean Frame-Freeze Duration is the mean duration, expressed in
      units of RTP timestamp from the sending side of the reporting
      block, of the frame-freeze events.  The value of Mean Frame-Freeze
      Duration is calculated by summing the total duration of all frame
      freeze events and dividing by the number of events.  This metric
      is optional.  It only exists when Video Loss Concealment Method
      Type=10.

   Mean Impaired Frame Proportion (MIFP): 8 bits

      Mean Impaired Frame Proportion is the mean proportion of each
      video frame impaired by loss before applying any loss concealment
      method during the interval, expressed as a fixed-point number with
      the binary point at the left edge of the field.  It is calculated
      by summing the impaired proportion of each video frame and
      dividing by the number of frames during this period.  The impaired
      proportion of each video frame is obtained by dividing the number
      of missing macroblocks from this video frame by the total
      macroblock number of the video frame, which is equivalent to
      multiplying the result of the division by 256, limiting the
      maximum value to 255 (to avoid overflow), and taking the integer
      part.

      If a video frame is totally lost, a value of 0xFF SHOULD be used
      for the frame when calculating the MIFP.

   Mean Concealed Frame Proportion (MCFP): 8 bits

      Mean Concealed Frame Proportion is the mean proportion of each
      video frame to which loss concealment (depicted as "V" in the
      definition of "Video Loss Concealment Method Type") was applied
      during the interval, expressed as a fixed-point number with the
      binary point at the left edge of the field.  It is calculated by
      summing the concealed proportion of each video frame and dividing
      by the number of frames during this period.  The concealed
      proportion of each video frame is obtained by dividing the number
      of concealed macroblocks from this video frame by the total
      macroblock number of the video frame, which is equivalent to
      multiplying the result of the division by 256, limiting the
      maximum value to 255 (to avoid overflow), and taking the integer
      part.




Huang                        Standards Track                    [Page 7]

RFC 7867              Video LC Metrics for RTCP XR             July 2016


      When calculating the MCFP, a value of 0xFF SHOULD be used for a
      lost frame that is totally concealed, and a value of 0 SHOULD be
      used for the frame if there are no concealed macroblocks in it.
      For Video Loss Concealment Method Type=10, each frame covered in
      the period of frame freeze is considered to be totally concealed;
      this means a value of 0xFF MUST be assigned.

   Fraction of Frames Subject to Concealment (FFSC): 8 bits

      Fraction of Frames Subject to Concealment is calculated by
      dividing the number of frames to which loss concealment (using
      Video Loss Concealment Method Type) was applied by the total
      number of frames and expressing this value as a fixed-point number
      with the binary point at the left edge of the field.  It is
      equivalent to multiplying the result of the division by 256,
      limiting the maximum value to 255 (to avoid overflow), and taking
      the integer part.

      A value of 0 indicates that there were no concealed frames, and a
      value of 0xFF indicates that the frames in the entire measurement
      interval are all concealed.

   Reserved: 8 bits

      These bits are reserved for future use.  They MUST be set to zero
      by senders and ignored by receivers (see Section 4.2 of
      [RFC6709]).

5.  SDP Signaling

   [RFC3611] defines the use of the Session Description Protocol (SDP)
   for signaling the use of RTCP XR blocks.

5.1.  SDP rtcp-xr-attrib Attribute Extension

   This session augments the SDP attribute "rtcp-xr" defined in Section
   5.1 of [RFC3611] by providing an additional value of "xr-format" to
   signal the use of the report block defined in this document.  The
   ABNF [RFC5234] syntax is as follows.

   xr-format =/ xr-vlc-block

   xr-vlc-block = "vlc"








Huang                        Standards Track                    [Page 8]

RFC 7867              Video LC Metrics for RTCP XR             July 2016


5.2.  Offer/Answer Usage

   When SDP is used in an offer/answer context, the SDP Offer/Answer
   usage defined in Section 5.2 of [RFC3611] for the unilateral
   "rtcp-xr" attribute parameters applies.  For detailed usage of
   Offer/Answer for unilateral parameters, refer to Section 5.2 of
   [RFC3611].

6.  Security Considerations

   It is believed that this RTCP XR block introduces no new security
   considerations beyond those described in [RFC3611].  This block does
   not provide per-packet statistics, so the risk to confidentiality
   documented in paragraph 3 of Section 7 of [RFC3611] does not apply.

   An attacker is likely to put incorrect information in the Video Loss
   Concealment reports; this will affect the estimation of the
   performance of video loss concealment mechanisms and the QoE of
   users.  Implementers SHOULD consider the guidance in [RFC7202] for
   using appropriate security mechanisms, i.e., where security is a
   concern, the implementation SHOULD apply encryption and
   authentication to the report block.  For example, this can be
   achieved by using the AVPF profile together with the Secure RTP
   profile as defined in [RFC3711]; an appropriate combination of the
   two profiles (an "SAVPF") is specified in [RFC5124].  However, other
   mechanisms also exist (documented in [RFC7201]) and might be more
   suitable.

7.  IANA Considerations

   New block types for RTCP XR are subject to IANA registration.  For
   general guidelines on IANA considerations for RTCP XR, please refer
   to [RFC3611].

7.1.  New RTCP XR Block Type Value

   This document assigns the block type value 34 to Video Loss
   Concealment Metric Report Block in the IANA "RTP Control Protocol
   Extended Reports (RTCP XR) Block Type Registry".

7.2.  New RTCP XR SDP Parameter

   This document also registers a new parameter "video-loss-concealment"
   in the "RTP Control Protocol Extended Reports (RTCP XR) Session
   Description Protocol (SDP) Parameters Registry".






Huang                        Standards Track                    [Page 9]

RFC 7867              Video LC Metrics for RTCP XR             July 2016


7.3.  Contact Information for Registrations

   The contact information for the registration is:

      RAI Area Directors <rai-ads@ietf.org>

8.  References

8.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <http://www.rfc-editor.org/info/rfc2119>.

   [RFC3550]  Schulzrinne, H., Casner, S., Frederick, R., and V.
              Jacobson, "RTP: A Transport Protocol for Real-Time
              Applications", STD 64, RFC 3550, DOI 10.17487/RFC3550,
              July 2003, <http://www.rfc-editor.org/info/rfc3550>.

   [RFC3611]  Friedman, T., Ed., Caceres, R., Ed., and A. Clark, Ed.,
              "RTP Control Protocol Extended Reports (RTCP XR)",
              RFC 3611, DOI 10.17487/RFC3611, November 2003,
              <http://www.rfc-editor.org/info/rfc3611>.

   [RFC3711]  Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K.
              Norrman, "The Secure Real-time Transport Protocol (SRTP)",
              RFC 3711, DOI 10.17487/RFC3711, March 2004,
              <http://www.rfc-editor.org/info/rfc3711>.

   [RFC5124]  Ott, J. and E. Carrara, "Extended Secure RTP Profile for
              Real-time Transport Control Protocol (RTCP)-Based Feedback
              (RTP/SAVPF)", RFC 5124, DOI 10.17487/RFC5124, February
              2008, <http://www.rfc-editor.org/info/rfc5124>.

   [RFC5234]  Crocker, D., Ed., and P. Overell, "Augmented BNF for
              Syntax Specifications: ABNF", STD 68, RFC 5234,
              DOI 10.17487/RFC5234, January 2008,
              <http://www.rfc-editor.org/info/rfc5234>.

   [RFC6776]  Clark, A. and Q. Wu, "Measurement Identity and Information
              Reporting Using a Source Description (SDES) Item and an
              RTCP Extended Report (XR) Block", RFC 6776,
              DOI 10.17487/RFC6776, October 2012,
              <http://www.rfc-editor.org/info/rfc6776>.






Huang                        Standards Track                   [Page 10]

RFC 7867              Video LC Metrics for RTCP XR             July 2016


   [RFC7294]  Clark, A., Zorn, G., Bi, C., and Q. Wu, "RTP Control
              Protocol (RTCP) Extended Report (XR) Blocks for
              Concealment Metrics Reporting on Audio Applications",
              RFC 7294, DOI 10.17487/RFC7294, July 2014,
              <http://www.rfc-editor.org/info/rfc7294>.

8.2.  Informative References

   [RFC6390]  Clark, A. and B. Claise, "Guidelines for Considering New
              Performance Metric Development", BCP 170, RFC 6390,
              DOI 10.17487/RFC6390, October 2011,
              <http://www.rfc-editor.org/info/rfc6390>.

   [RFC6709]  Carpenter, B., Aboba, B., Ed., and S. Cheshire, "Design
              Considerations for Protocol Extensions", RFC 6709,
              DOI 10.17487/RFC6709, September 2012,
              <http://www.rfc-editor.org/info/rfc6709>.

   [RFC6792]  Wu, Q., Ed., Hunt, G., and P. Arden, "Guidelines for Use
              of the RTP Monitoring Framework", RFC 6792,
              DOI 10.17487/RFC6792, November 2012,
              <http://www.rfc-editor.org/info/rfc6792>.

   [RFC7201]  Westerlund, M. and C. Perkins, "Options for Securing RTP
              Sessions", RFC 7201, DOI 10.17487/RFC7201, April 2014,
              <http://www.rfc-editor.org/info/rfc7201>.

   [RFC7202]  Perkins, C. and M. Westerlund, "Securing the RTP
              Framework: Why RTP Does Not Mandate a Single Media
              Security Solution", RFC 7202, DOI 10.17487/RFC7202, April
              2014, <http://www.rfc-editor.org/info/rfc7202>.




















Huang                        Standards Track                   [Page 11]

RFC 7867              Video LC Metrics for RTCP XR             July 2016


Appendix A.  Metrics Represented Using the Template from RFC 6390

   a. Video Impaired Duration Metric

      *  Metric Name: Video Impaired Duration Metric

      *  Metric Description: The total duration of the video impaired by
         transmission loss before applying any loss concealment methods.

      *  Method of Measurement or Calculation: The metric is based on
         measurements that are typically made at the time that a video
         frame is decoded and rendered for playout.

      *  Units of Measurement: This metric is expressed in units of RTP
         timestamp.

      *  Measurement Point(s) with Potential Measurement Domain: It is
         measured at the receiving end of the RTP stream.

      *  Measurement Timing: See paragraph 1 of Section 4.

      *  Use and Applications: The metric is applicable to video
         applications of RTP and the video component of audio/video
         applications in which packet loss concealment mechanisms are
         applied to the receiving endpoint to mitigate the impact of
         network impairments on QoE.

   b. Video Concealed Duration Metric

      *  Metric Name: Video Concealed Duration Metric

      *  Metric Description: The total duration of concealed damaged
         video pictures on which loss concealment method corresponding
         to Video Loss Concealment Method Type is applied.

      *  Method of Measurement or Calculation: The metric is based on
         measurements that are typically made at the time that a video
         frame is decoded and rendered for playout.

      *  Units of Measurement: This metric is expressed in units of RTP
         timestamp.

      *  Measurement Point(s) with Potential Measurement Domain: It is
         measured at the receiving end of the RTP stream.

      *  Measurement Timing: See paragraph 1 of Section 4.





Huang                        Standards Track                   [Page 12]

RFC 7867              Video LC Metrics for RTCP XR             July 2016


      *  Use and Applications: These metrics are applicable to video
         applications of RTP and the video component of audio/video
         applications in which packet loss concealment mechanisms are
         incorporated into the receiving endpoint to mitigate the impact
         of network impairments on QoE.

   c. Mean Video Frame-Freeze Duration Metric

      *  Metric Name: Mean Video Frame-Freeze Duration Metric

      *  Metric Description: The mean duration of the frame-freeze
         events.

      *  Method of Measurement or Calculation: The metric is based on
         measurements that are typically made at the time that a video
         frame is decoded and rendered for playout.  The metric is
         calculated by summing the total duration of all frame-freeze
         events and dividing by the number of events.

      *  Units of Measurement: This metric is expressed in units of RTP
         timestamp.

      *  Measurement Point(s) with Potential Measurement Domain: It is
         measured at the receiving end of the RTP stream.

      *  Measurement Timing: See paragraph 1 of Section 4.

      *  Use and Applications: These metrics are applicable to video
         applications of RTP and the video component of audio/video
         applications in which packet loss concealment mechanisms are
         incorporated into the receiving endpoint to mitigate the impact
         of network impairments on QoE.

   d. Mean Impaired Video Frame Proportion Metric

      *  Metric Name: Mean Impaired Video Frame Proportion Metric

      *  Metric Description: Mean proportion of each video frame
         impaired by loss before applying any loss concealment method
         during the interval.

      *  Method of Measurement or Calculation: The metric is based on
         measurements that are typically made at the time that a video
         frame is decoded and rendered for playout.  It is calculated by
         summing the impaired proportion of each video frame and
         dividing by the number of frames during this period.  The
         impaired proportion of each video frame is obtained by dividing
         the number of missing macroblocks from this video frame by the



Huang                        Standards Track                   [Page 13]

RFC 7867              Video LC Metrics for RTCP XR             July 2016


         total macroblock number of the video frame, which is equivalent
         to multiplying the result of the division by 256, limiting the
         maximum value to 255 (to avoid overflow), and taking the
         integer part.

      *  Units of Measurement: This metric is expressed as a fixed-point
         number with the binary point at the left edge of the field.

      *  Measurement Point(s) with Potential Measurement Domain: It is
         measured at the receiving end of the RTP stream.

      *  Measurement Timing: See paragraph 1 of Section 4.

      *  Use and Applications: These metrics are applicable to video
         applications of RTP and the video component of audio/video
         applications in which packet loss concealment mechanisms are
         incorporated into the receiving endpoint to mitigate the impact
         of network impairments on QoE.

   e. Mean Concealed Video Frame Proportion Metric

      *  Metric Name: Mean Concealed Video Frame Proportion Metric

      *  Metric Description: Mean proportion of each video frame to
         which loss concealment (using Video Loss Concealment Method
         Type) was applied during the interval.

      *  Method of Measurement or Calculation: The metric is based on
         measurements that are typically made at the time that a video
         frame is decoded and rendered for playout.  It is calculated by
         summing the concealed proportion of each video frame and
         dividing by the number of frames during this period.  The
         concealed proportion of each video frame is obtained by
         dividing the number of concealed macroblocks from this video
         frame by the total macroblock number of the video frame, which
         is equivalent to multiplying the result of the division by 256,
         limiting the maximum value to 255 (to avoid overflow), and
         taking the integer part.

      *  Units of Measurement: This metric is expressed as a fixed-point
         number with the binary point at the left edge of the field.

      *  Measurement Point(s) with Potential Measurement Domain: It is
         measured at the receiving end of the RTP stream.

      *  Measurement Timing: See paragraph 1 of Section 4.





Huang                        Standards Track                   [Page 14]

RFC 7867              Video LC Metrics for RTCP XR             July 2016


      *  Use and Applications: These metrics are applicable to video
         applications of RTP and the video component of audio/video
         applications in which packet loss concealment mechanisms are
         incorporated into the receiving endpoint to mitigate the impact
         of network impairments on QoE.

   f. Fraction of Video Frames Subject to Concealment Metric

      *  Metric Name: Fraction of Video Frames Subject to Concealment
         Metric

      *  Metric Description: Proportion of concealed video frames to
         which loss concealment (using the Video Loss Concealment Method
         Type) was applied compared to the total number of frames during
         the interval.

      *  Method of Measurement or Calculation: The metric is based on
         measurements that are typically made at the time that a video
         frame is decoded and rendered for playout.  This metric is
         calculated by dividing the number of frames to which loss
         concealment (using Video Loss Concealment Method Type) was
         applied by the total number of frames.  It is equivalent to
         multiplying the result of the division by 256, limiting the
         maximum value to 255 (to avoid overflow), and taking the
         integer part.

      *  Units of Measurement:  This metric is expressed as a fixed-
         point number with the binary point at the left edge of the
         field.

      *  Measurement Point(s) with Potential Measurement Domain: It is
         measured at the receiving end of the RTP stream.

      *  Measurement Timing: See paragraph 1 of Section 4.

      *  Use and Applications: These metrics are applicable to video
         applications of RTP and the video component of audio/video
         applications in which packet loss concealment mechanisms are
         incorporated into the receiving endpoint to mitigate the impact
         of network impairments on QoE.











Huang                        Standards Track                   [Page 15]

RFC 7867              Video LC Metrics for RTCP XR             July 2016


Acknowledgements

   The author would like to thank Colin Perkins and Roni Even for their
   valuable comments.

Authors' Addresses

   Rachel Huang
   Huawei
   101 Software Avenue, Yuhua District
   Nanjing 210012
   China

   Email: rachel.huang@huawei.com





































Huang                        Standards Track                   [Page 16]