Network Working Group D. Ruffen
Request for Comments: 2643 T. Len
Category: Informational J. Yanacek
Cabletron Systems Incorporated
August 1999
Cabletron's SecureFast VLAN Operational Model
Version 1.8
Status of this Memo
This memo provides information for the Internet community. It does
not specify an Internet standard of any kind. Distribution of this
memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (1999). All Rights Reserved.
Abstract
Cabletron's SecureFast VLAN (SFVLAN) product implements a distributed
connection-oriented switching protocol that provides fast forwarding
of data packets at the MAC layer. The product uses the concept of
virtual LANs (VLANs) to determine the validity of call connection
requests and to scope the broadcast of certain flooded messages.
Table of Contents
1. Introduction............................................. 3
1.1 Data Conventions..................................... 3
1.2 Definitions of Commonly Used Terms................... 4
2. SFVLAN Overview.......................................... 6
2.1 Features............................................. 7
2.2 VLAN Principles...................................... 8
2.2.1 Default, Base and Inherited VLANs.............. 8
2.2.2 VLAN Configuration Modes....................... 8
2.2.2.1 Endstations............................ 8
2.2.2.2 Ports.................................. 9
2.2.2.3 Order of Precedence.................... 9
2.2.3 Ports with Multiple VLAN Membership............ 10
2.3 Tag/Length/Value Method of Addressing................ 10
2.4 Architectural Overview............................... 11
3. Base Services............................................ 13
4. Call Processing.......................................... 14
4.1 Directory Service Center............................. 14
4.1.1 Local Add Server............................... 15
Ruffen, et al. Informational [Page 1]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
4.1.2 Inverse Resolve Server......................... 15
4.1.3 Local Delete Server............................ 18
4.2 Topology Service Center.............................. 18
4.2.1 Neighbor Discovery Server...................... 18
4.2.2 Spanning Tree Server........................... 18
4.2.2.1 Creating and Maintaining
the Spanning Tree........... 19
4.2.2.2 Remote Blocking........................ 19
4.2.3 Link State Server.............................. 20
4.3 Resolve Service Center............................... 21
4.3.1 Table Server................................... 22
4.3.2 Local Server................................... 22
4.3.3 Subnet Server.................................. 22
4.3.4 Interswitch Resolve Server..................... 22
4.3.5 Unresolvable Server............................ 23
4.3.6 Block Server................................... 23
4.4 Policy Service Center................................ 24
4.4.1 Unicast Rules Server........................... 24
4.5 Connect Service Center............................... 25
4.5.1 Local Server................................... 25
4.5.2 Link State Server.............................. 25
4.5.3 Directory Server............................... 26
4.6 Filter Service Center................................ 26
4.7 Path Service Center.................................. 26
4.7.1 Link State Server.............................. 26
4.7.2 Spanning Tree Server........................... 27
4.8 Flood Service Center................................. 27
4.8.1 Tag-Based Flood Server......................... 27
5. Monitoring Call Connections.............................. 27
5.1 Definitions.......................................... 27
5.2 Tapping a Connection................................. 28
5.2.1 Types of Tap Connections....................... 28
5.2.2 Locating the Probe and Establishing
the Tap Connection.......... 29
5.2.3 Status Field................................... 30
5.3 Untapping a Connection............................... 31
6. Interswitch Message Protocol (ISMP)...................... 32
6.1 General Packet Structure............................. 32
6.1.1 Frame Header................................... 32
6.1.2 ISMP Packet Header............................. 33
6.1.2.1 Version 2.............................. 33
6.1.2.2 Version 3.............................. 34
6.1.3 ISMP Message Body.............................. 35
6.2 Interswitch BPDU Message............................. 35
6.3 Interswitch Remote Blocking Message.................. 36
6.4 Interswitch Resolve Message.......................... 37
6.4.1 Prior to Version 1.8........................... 37
6.4.2 Version 1.8.................................... 41
Ruffen, et al. Informational [Page 2]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
6.5 Interswitch New User Message......................... 46
6.6 Interswitch Tag-Based Flood Message.................. 49
6.6.1 Prior to Version 1.8........................... 49
6.6.2 Version 1.8.................................... 52
6.7 Interswitch Tap/Untap Message........................ 55
7. Security Considerations.................................. 58
8. References............................................... 58
9. Authors' Addresses....................................... 59
10. Full Copyright Statement................................ 60
1. Introduction
This memo is being distributed to members of the Internet community
in order to solicit reactions to the proposals contained herein.
While the specification discussed here may not be directly relevant
to the research problems of the Internet, it may be of interest to
researchers and implementers.
1.1 Data Conventions
The methods used in this memo to describe and picture data adhere to
the standards of Internet Protocol documentation [RFC1700]. In
particular:
The convention in the documentation of Internet Protocols is to
express numbers in decimal and to picture data in "big-endian"
order. That is, fields are described left to right, with the most
significant octet on the left and the least significant octet on
the right.
The order of transmission of the header and data described in this
document is resolved to the octet level. Whenever a diagram shows
a group of octets, the order of transmission of those octets is
the normal order in which they are read in English.
Whenever an octet represents a numeric quantity the left most bit
in the diagram is the high order or most significant bit. That
is, the bit labeled 0 is the most significant bit.
Ruffen, et al. Informational [Page 3]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
Similarly, whenever a multi-octet field represents a numeric
quantity the left most bit of the whole field is the most
significant bit. When a multi-octet quantity is transmitted the
most significant octet is transmitted first.
1.2 Definitions of Commonly Used Terms
This section contains a collection of definitions for terms that have
a specific meaning for the SFVLAN product and that are used
throughout the text.
Switch ID
A 10-octet value that uniquely identifies an SFVLAN switch within
the switch fabric. The value consists of the 6-octet base MAC
address of the switch, followed by 4 octets of zeroes.
Network link
The physical connection between two switches. A network link is
associated with a network interface (or port) of a switch.
Network port
An interface on a switch that attaches to another switch.
Access port
An interface on a switch that attaches to a user endstation.
Port ID
A 10-octet value that uniquely identifies an interface of a
switch. The value consists of the 6-octet base MAC address of the
switch, followed by the 4-octet local port number of the
interface.
Neighboring switches
Two switches attached to a common (network) link.
Call connection
A mapping of user traffic through a switch that correlates the
source and destination address pair specified within the packet to
an inport and outport pair on the switch.
Ruffen, et al. Informational [Page 4]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
Call connection path
A set of 0 to 7 network links over which user traffic travels
between the source and destination endstations. Call connection
paths are selected from a list of alternate equal cost paths
calculated by the VLS protocol [IDvlsp], and are chosen to load
balance traffic across the fabric.
Ingress switch
The owner switch of the source endstation of a call connection.
That is, the source endstation is attached to one of the local
access ports of the switch.
Egress switch
The owner switch of the destination endstation of a call
connection. That is, the destination endstation is attached to
one of the local access ports of the switch.
Intermediate switches
Any switch along the call connection path on which user traffic
enters and leaves over network links. Note that the following
types of connections have no intermediate switches:
- Call connections between source and destination endstations
that are attached to the same switch -- that is, the ingress
switch is the same as the egress switch. Note also that the
path for this type of connection consists of 0 network links.
- Call connections where the ingress and egress switches are
physical neighbors connected by a single network link. The
path for this type of connection consists of a single network
link.
InterSwitch Message protocol (ISMP)
The protocol used for interswitch communication between SFVLAN
switches.
Undirected messages
Messages that are (potentially) sent to all SFVLAN switches in the
switch fabric -- that is, they are not directed to any particular
switch. ISMP messages with a message type of 5, 7 or 8 are
undirected messages.
Ruffen, et al. Informational [Page 5]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
Switch flood path
The path used to send undirected messages throughout the switch
fabric. The switch flood path is formed using a spanning tree
algorithm that provides a single path through the switch fabric
that guarantees loop-free delivery to every other SFVLAN switch in
the fabric.
Upstream Neighbor
That switch attached to the inport of the switch flood path --
that is, the switch from which undirected messages are received.
Note that each switch receiving an undirected message has, at
most, one upstream neighbor, and the originator of any undirected
ISMP message has no upstream neighbors.
Downstream Neighbors
Those switches attached to all outports of the switch flood path
except the port on which the undirected message was received.
Note that for each undirected message some number of switches have
no downstream neighbors.
Virtual LAN (VLAN) identifier
A VLAN is a logical grouping of ports and endstations such that
all ports and endstations in the VLAN appear to be on the same
physical (or extended) LAN segment even though they may be
geographically separated.
A VLAN identifier consists of a variable-length string of octets.
The first octet in the string contains the number of octets in the
remainder of the string -- the actual VLAN identifier value. A
VLAN identifier can be from 1 to 16 octets long.
VLAN policy
Each VLAN has an assigned policy value used to determine whether a
particular call connection can be established. SFVLAN recognizes
two policy values: Open and Secure.
2. SFVLAN Overview
Cabletron's SecureFast VLAN (SFVLAN) product implements a distributed
connection-oriented switching protocol that provides fast forwarding
of data packets at the MAC layer.
Ruffen, et al. Informational [Page 6]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
2.1 Features
Within a connection-oriented switching network, user traffic is
routed through the switch fabric based on the source and destination
address (SA/DA) pair found in the arriving packet. For each SA/DA
pair encountered by a switch, a "connection" is programmed into the
switch hardware. This connection maps the SA/DA pair and the port on
which the packet was received to a specific outport over which the
packet is to be forwarded. Thus, once a connection has been
established, all packets with a particular SA/DA pair arriving on a
particular inport are automatically forwarded by the switch hardware
out the specified outport.
A distributed switching environment requires that each switch be
capable of processing all aspects of the call processing and
switching functionality. Thus, each switch must synchronize its
various databases with all other switches in the fabric or be capable
of querying other switches for information it does not have locally.
SFVLAN accomplishes the above objectives by providing the following
features:
- A virtual directory of the entire switch fabric.
- Call processing for IP, IPX and MAC protocols.
- Automatic call connection, based on VLAN policy.
- Automatic call rerouting around failed switches and links.
In addition, SFVLAN optimizes traffic flow across the switch fabric
by providing the following features:
- Broadcast interception and address resolution at the ingress port.
- Broadcast scoping, restricting the flooding of broadcast packets
to only those ports that belong to the same VLAN as the packet
source.
- A single loop-free path (spanning tree) used for the flooding of
undirected interswitch control messages. Only switches running
the SFVLAN switching protocol are included in this spanning tree
calculation -- that is, traditional bridges or routers configured
for bridging are not included.
- Interception of both service and route advertisements with
readvertisement sourced from the MAC address of the original
advertiser.
Ruffen, et al. Informational [Page 7]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
2.2 VLAN Principles
Each SFVLAN switch port, along with its attached endstations, belongs
to one or more virtual LANs (VLANs). A VLAN is a logical grouping of
ports and endstations such that all ports and endstations in the VLAN
appear to be on the same physical (or extended) LAN segment even
though they may be geographically separated.
VLAN assignments are used to determine the validity of call
connection requests and to scope the broadcast of certain flooded
messages.
2.2.1 Default, Base and Inherited VLANs
Each port is explicitly assigned to a default VLAN. At start-up, the
default VLAN to which all ports are assigned is the base VLAN -- a
permanent, non-deletable VLAN to which all ports belong at all times.
The network administrator can change the default VLAN of a port from
the base VLAN to any other unique VLAN by using a management
application known here as the VLAN Manager. A port's default VLAN is
persistent -- that is, it is preserved across a switch reset.
When an endstation attaches to a port for the first time, it inherits
the default VLAN of the port. Using the VLAN Manager, the network
administrator can reassign an endstation to another VLAN.
Note:
When all ports and all endstations belong to the base VLAN, the
switch fabric behaves like an 802.1D bridging system.
2.2.2 VLAN Configuration Modes
For both ports and endstations, there are a variety of VLAN
configuration types, or modes.
2.2.2.1 Endstations
For endstations, there are two VLAN configuration modes: inherited
and static.
- Inherited
An inherited endstation becomes a member of its port's default
VLAN.
Ruffen, et al. Informational [Page 8]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
- Static
A static port becomes a member of the VLAN to which it has been
assigned by the VLAN Manager.
The default configuration mode for an endstation is inherited.
2.2.2.2 Ports
For ports, there are two VLAN configuration modes: normal and
locked.
- Normal
All inherited endstations on a normal port become members of the
port's default VLAN. All static endstations are members of the
VLAN to which they were mapped by the VLAN Manager.
If the VLAN Manager reassigns the default VLAN of a normal port,
the VLAN(s) for the attached endstations may or may not change,
depending on the VLAN configuration mode of each endstation. All
inherited endstations will become members of the new default VLAN.
All others will retain membership in their previously mapped
VLANs.
- Locked
All endstations attached to a locked port can be members only of
the port's default VLAN.
If the VLAN Manager reconfigures a normal port to be a locked
port, all endstations attached to the port become members of the
port's default VLAN, regardless of any previous VLAN membership.
The default configuration mode for ports is normal.
2.2.2.3 Order of Precedence
On a normal port, static VLAN membership prevails over inherited
membership.
On a locked port, default VLAN membership prevails over any static
VLAN membership.
If a statically assigned endstation moves from a locked port back to
a normal port, the endstation's static VLAN membership must be
preserved.
Ruffen, et al. Informational [Page 9]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
2.2.3 Ports with Multiple VLAN Membership
A port can belong to multiple VLANs, based on the VLAN membership of
its attached endstations.
For example, consider a port with three endstations, a default VLAN
of "blue" and the following endstation VLAN assignments:
- One of the endstations is statically assigned to VLAN "red."
- Another endstation is statically assigned to VLAN "green."
- The third endstation inherits the default VLAN of "blue."
In this instance, the port is explicitly a member of VLAN "blue." But
note that it is also implicitly a member of VLAN "red" and VLAN
"green." Any tag-based flooding (Section 4.8) directed to any one of
the three VLANs ("red," "green," or "blue") will be forwarded out the
port.
2.3 Tag/Length/Value Method of Addressing
Within most computer networks, the concept of "address" is somewhat
elusive because different protocols can (and do) use different
addressing schemes and formats. For example, Ethernet (physical
layer) addresses are six octets long, while IP (network layer)
addresses are only four octets long.
To distinguish between the various protocol-specific forms of
addressing, many software modules within the SFVLAN product specify
addresses in a format known as Tag/Length/Value (TLV). This format
uses a variable-length construct as shown below:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Tag |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value length | |
+-+-+-+-+-+-+-+-+ +
| Address value |
: :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Tag
This 4-octet field specifies the type of address contained in the
structure. The following address types are currently supported:
Ruffen, et al. Informational [Page 10]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
Tag name Value Address type
aoMacDx 1 DX ethernet dst/src/type
aoIpxSap 2 Sap
aoIpxRIP 3 RIP
aoInstYP 4 YP (YP name and version)
aoInstUDP 5 UDP (Port #)
aoIpxIpx 6 Ipx
aoInetIP 7 IP (Net address)
aoInetRPC 8 RPC (Program #)
aoInetRIP 9 INET RIP
aoMacDXMcast 10 Multicast unknown type
aoAtDDP 11 AppleTalk DDP
aoEmpty 12 (no address type specified)
aoVlan 13 VLAN identifier
aoHostName 14 Host name
aoNetBiosName 15 NetBIOS name
aoNBT 16 NetBIOS on TCP name
aoInetIPMask 17 IP Subnet Mask
aoIpxSap8022 18 Sap 8022 type service
aoIpxSapSnap 19 Sap Snap type service
aoIpxSapEnet 20 Sap Enet type service
aoDHCPXID 21 DHCP Transaction ID
aoIpMcastRx 22 IP class D receiver
aoIpMcastTx 23 IP class D sender
aoIpxRip8022 24 Ipx Rip 8022 type service
aoIpxRipSnap 25 Ipx Rip type service
aoIpxRipEnet 26 Ipx Rip Enet service
aoATM 27 ATM
aoATMELAN 28 ATM LAN Emulation Name
Value length
This 1-octet field contains the length of the value of the
address. The value here depends on the address type and actual
value.
Address value
This variable-length field contains the value of the address. The
length of this field is stored in the Value length field.
2.4 Architectural Overview
The SFVLAN software executes in the switch CPU and consists of the
following elements as shown in Figure 1:
Ruffen, et al. Informational [Page 11]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
- The SFVLAN base services that handles traffic intercepted by the
switch hardware. The base services are described in Section 3.
+------------------------------------------------------+
| +-----+ |
| +------------+ | I | |
| | CALL TAP <--(8)--> N | |
| +------------+ | T | |
| | E | |
| +-----------+ +------------+ | R | |
| | PATH | | TOPOLOGY | | S | |
| | | | | | W | |
| | Lnk state <------> Lnk state <--(3)--> I | | Flood path
| | | | | | T <----(5,7,8)-->
| | Span tree <------> Span tree <--(4)--> C | |
| +--^--------+ | | | H | |
| | | Discovery <--(2)--> | |
| | +------------+ | M | |
| | | E | |
| +------^--+ +--------+ | S | |
| | CONNECT >---------+--> FILTER | | S | |
| +--^------+ | +--------+ | A | | specific
| | | | G | | netwrk lnks
| | +--------^-+ +-------+ | E <----(2,3,4)-->
| +-------< POLICY | | FLOOD >--(7)--> | |
| +------^---+ +-^-----+ | P | |
| | | | R | |
| +-----------+ +-^-----------V-+ | O | |
| | DIRECTORY <----> RESOLVE <------(5)--> T | |
| +-----^-----+ +---^-----------+ | O | |
| | | | C | |
| | +---------^-----------+ | O | |
| +----< Base Services | | L | |
| +-----^---------------+ +-----+ |
+------------------|-----------------------------------+
Switch CPU |
| Host control port
+-----O----------------+
| ^ no cnx |
Layer 2 | | |
---------->O-----+--------------->O----------->
SA/DA pr | known cnx |
+----------------------+
Switch hardware
Figure 1: SFVLAN Architectural Overview
Ruffen, et al. Informational [Page 12]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
- Eight call processing service centers that provide the essential
services required to process call connections. The call
processing service centers are described in Section 4.
- A Call Tap module that supports the monitoring of call
connections. The Call Tap module is described in Section 5.
- The InterSwitch Message Protocol (ISMP) that provides a consistent
method of encapsulating and transmitting control messages
exchanged between SFVLAN switches. (Note that ISMP is not a
discrete software module. Instead, its functionality is
distributed among those service centers and software modules that
need to communicate with other switches in the fabric.) The
Interswitch Message Protocol and the formats of the individual
interswitch messages are described in Section 6.
3. Base Services
The SFVLAN base services act as the interface between the switch
hardware and the SFVLAN service centers running on the switch CPU.
This relationship is shown in Figure 2. This figure is a replication
of the bottom portion of Figure 1.
| Directory Resolve |
| ^ ^ |
| | | |
| | +---------^-----------+ |
| +----< Base Services | |
| +-----^---------------+ |
+-------------------|--------------------------+
Switch CPU |
| Host control port
+-----O----------------+
| ^ no cnx |
Layer 2 | | |
---------->O-----+--------------->O----------->
SA/DA pr | known cnx |
+----------------------+
Switch hardware
Figure 2: Base Services
Ruffen, et al. Informational [Page 13]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
During normal operation of the switch, data packets arriving at
any one of the local switch ports are examined in the switch
hardware. If the packet's source and destination address (SA/DA)
pair match a known connection, the hardware simply forwards the
packet out the outport specified by the connection.
If the SA/DA pair do not match any known connection, the hardware
diverts the packet to the host control port where it is picked up
by the SFVLAN base services. The base services generate a
structure known as a state box that tracks the progress of the
call connection request as the request moves through the call
processing service centers.
After creating the call's state box, the base services check to
determine if the call is a duplicate of a call already being
processed. If not, a request is issued to the Directory Service
Center (Section 4.1) to add the call's source address to the local
Node and Alias Tables. The base services then hand the call off to
the Resolve Service Center (Section 4.3) for further processing.
4. Call Processing
Call connection processing is handled by a set of eight service
centers, each with one or more servers. The servers within a
service center are called in a particular sequence. Each server
records the results of its processing in the call connection
request state box and passes the state box to the next server in
the sequence.
In the sections that follow, servers are listed in the order in
which they are called.
4.1 Directory Service Center
The Directory Service Center is responsible for cataloging the MAC
addresses and alias information for both local and remote
endstations. The information is stored in two tables -- the Node
Table and the Alias Table.
- The Node Table contains the MAC addresses of endstations
attached to the local switch. It also contains a cache of
remote endstations detected by the Resolve Service Center
(Section 4.3). Every entry in the Node Table has one or more
corresponding entries in the Alias Table.
Ruffen, et al. Informational [Page 14]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
- The Alias Table contains protocol alias information for each
endstation. An endstation alias can be a network address (such
as an IP or IPX address), a VLAN identifier, or any other
protocol identifier. Since every endstation is a member of at
least one VLAN (the default VLAN for the port), there is always
at least one entry in the Alias Table for each entry in the
Node Table.
Note:
The Node and Alias Tables must remain synchronized.
That is, when an endstation's final alias is removed
from the Alias Table, the endstation entry is removed
from the Node Table.
Note that the total collection of all Node Tables and Alias Tables
across all switches is known as the "virtual" directory of the
switch fabric. The virtual directory contains address mappings of
all known endstations in the fabric.
4.1.1 Local Add Server
The Directory Local Add server adds entries to the local Node or
Alias Tables. It is called by the base services (Section 3) to
add a local endstation and by the Interswitch Resolve (Section
4.3.4) server to add an endstation discovered on a remote switch.
4.1.2 Inverse Resolve Server
The Directory Inverse Resolve server is invoked when a new
endstation has been discovered on the local switch (that is, when
the Local Add server was successful in adding the endstation).
The server provides two functions:
- It populates the Node and Alias Tables with local entries
during switch initialization.
- It processes a new endstation discovered after the fabric
topology has converged to a stable state.
In both instances, the processing is identical.
Ruffen, et al. Informational [Page 15]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
When a new endstation is detected on one of the switch's local
ports, the Inverse Resolve server sends an Interswitch New User
request message (Section 6.5) over the switch flood path to all
other switches in the fabric. The purpose of the Interswitch New
User request is two-fold:
- It informs the other switches of the new endstation address.
Any entries for that endstation in the local databases of other
switches should be dealt with appropriately.
- It requests information about any static VLAN(s) to which the
endstation has been assigned.
When a switch receives an Interswitch New User request message
from one of its upstream neighbors, it first forwards the message
to all its downstream neighbors. No actual processing or VLAN
resolution is attempted until the message reaches the end of the
switch flood path and begins its trip back along the return path.
This ensures that all switches in the fabric receive notification
of the new user and have synchronized their databases.
If a switch receives an Interswitch New User request message but
has no downstream neighbors, it does the following:
- If the endstation was previously connected to one of the
switch's local ports, the switch formulates an Interswitch New
User Response message by loading the VLAN identifier(s) of the
static VLAN(s) to which the endstation was assigned, along with
its own MAC address. (VLAN identifiers are stored in
Tag/Length/Value (TLV) format. See Section 2.3.) The switch
then sets the message status field to NewUserAck, and returns
the message to its upstream (requesting) neighbor.
Otherwise, the switch sets the status field to NewUserUnknown
and returns the message to its upstream neighbor.
- The switch then deletes the endstation from its local database,
as well as any entries associated with the endstation in its
connection table.
When a switch forwards an Interswitch New User request message to
its downstream neighbors, it keeps track of the number of requests
it has sent out and does not respond back to its upstream neighbor
until all requests have been responded to.
Ruffen, et al. Informational [Page 16]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
- As each response is received, the switch checks the status
field of the message. If the status is NewUserAck, the switch
retains the information in that response. When all requests
have been responded to, the switch returns the NewUserAck
response to its upstream neighbor.
- If all the Interswitch New User Request messages have been
responded to with a status of NewUserUnknown, the switch checks
to see if the endstation was previously connected to one of its
local ports. If so, the switch formulates an Interswitch New
User Response message by loading the VLAN identifier(s) of the
static VLAN(s) to which the endstation was assigned, along with
its own MAC address. The switch then sets the message status
field to NewUserAck, and returns the message to its upstream
(requesting) neighbor.
Otherwise, the switch sets the status field to NewUserUnknown
and returns the message to its upstream neighbor.
- The switch then deletes the endstation from its local database,
as well as any entries associated with the endstation in its
connection table.
When the originating switch has received responses to all the
Interswitch New User Request messages it has sent, it does the
following:
- If it has received a response message with a status of
NewUserAck, it loads the new VLAN information into its local
database.
- If all responses have been received with a status of
NewUserUnknown, the originating switch assumes that the
endstation was not previously connected anywhere in the network
and assigns it to a VLAN according to the VLAN membership rules
and order of precedence.
If any Interswitch New User Request message has not been responded
to within a certain predetermined time (currently 5 seconds), the
originating switch recalculates the switch flood path and resends
the Interswitch New User Request message.
Ruffen, et al. Informational [Page 17]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
4.1.3 Local Delete Server
The Directory Local Delete server removes entries (both local and
remote) from the local Node and Alias Tables. It is invoked when
an endstation, previously known to be attached to one switch, has
been moved and discovered on another switch.
Note also that remote entries are cached and are purged from the
tables on a first-in/first-out basis as space is needed in the
cache.
4.2 Topology Service Center
The Topology Service Center is responsible for maintaining three
databases relating to the topology of the switch fabric:
- The topology table of SFVLAN switches that are physical
neighbors to the local switch.
- The spanning tree that defines the loop-free switch flood path
used for transmitting undirected interswitch messages.
- The directed graph that is used to calculate the best path(s)
for call connections.
4.2.1 Neighbor Discovery Server
The Topology Neighbor Discovery server uses Interswitch Keepalive
messages to detect the switch's neighbors and establish the
topology of the switching fabric. Interswitch Keepalive messages
are exchanged in accordance with Cabletron's VlanHello protocol,
described in detail in [IDhello].
4.2.2 Spanning Tree Server
The Topology Spanning Tree server is invoked by the Topology
Neighbor Discovery server when a neighboring SFVLAN switch is
either discovered or lost -- that is, when the operational status
of a network link changes.
The Spanning Tree server exchanges interswitch messages with
neighboring SFVLAN switches to calculate the switch flood path
over which undirected interswitch messages are sent. There are
two parts to this process:
- Creating and maintaining the spanning tree
- Remote blocking
Ruffen, et al. Informational [Page 18]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
4.2.2.1 Creating and Maintaining the Spanning Tree
In a network with redundant network links, a packet traveling between
switches can potentially be caught in an infinite loop -- an
intolerable situation in a networking environment. However, it is
possible to reduce a network topology to a single configuration
(known as a spanning tree) such that there is, at most, one path
between any two switches.
Within the SFVLAN product, the spanning tree is created and
maintained using the Spanning Tree Algorithm defined by the IEEE
802.1d standard.
Note:
A detailed discussion of this algorithm is beyond the scope of
this document. See [IEEE] for more information.
To implement the Spanning Tree Algorithm, SFVLAN switches exchange
Interswitch BPDU messages (Section 6.2) containing encapsulated
IEEE-compliant 802.2 Bridge Protocol Data Units (BPDUs). There are
two types of BPDUs:
- Configuration (CFG) BPDUs are exchanged during the switch
discovery process, following the receipt of an Interswitch
Keepalive message. They are used to create the initial the
spanning tree.
- Topology Change Notification (TCN) BPDUs are exchanged when
changes in the network topology are detected. They are used to
redefine the spanning tree to reflect the current topology.
See [IEEE] for detailed descriptions of these BPDUs.
4.2.2.2 Remote Blocking
After the spanning tree has been computed, each network port on an
SFVLAN switch will be in one of two states:
- Forwarding. A port in the Forwarding state will be used to
transmit all ISMP messages.
Ruffen, et al. Informational [Page 19]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
- Blocking. A port in the Blocking state will not be used to
forward undirected ISMP messages. Blocking the rebroadcast of
these messages on selected ports prevents message duplication
arising from multiple paths that exist in the network topology.
Note that all other types of ISMP message will be transmitted.
Note:
The IEEE 802.1d standard specifies other port states used
during the initial creation of the spanning tree. These states
are not relevant to the discussion here.
Note that although a port in the Blocking state will not forward
undirected ISMP messages, it may still receive them. Any such
message received will ultimately be discarded, but at the cost of CPU
time necessary to process the packet.
To prevent the transmission of undirected messages to a port, the
port's owner switch can set remote blocking on the link by sending an
Interswitch Remote Blocking message (Section 6.3) out over the port.
This notifies the switch on the other end of the link that undirected
messages should not be sent over the link, regardless of the state of
the sending port.
Each SFVLAN switch sends an Interswitch Remote Blocking message out
over all its blocked network ports every 5 seconds. A flag within
the message indicates whether remote blocking should be turned on or
off over the link.
4.2.3 Link State Server
The Topology Link State server is invoked by any process that detects
a change in the state of the network links of the local switch.
These changes include (but are not limited to) changes in operational
or administrative status of the link, path "cost" or bandwidth.
The Link State server runs Cabletron's Virtual LAN Link State (VLS)
protocol which exchanges interswitch messages with neighboring SFVLAN
switches to calculate the set of best paths between the local switch
and all other switches in the fabric. (The VLS protocol is described
in detail in [IDvlsp].)
The Link State server also notifies the Connect Service Center
(Section 4.5) of any remote links that have failed, thereby
necessitating potential tear-down of current connections.
Ruffen, et al. Informational [Page 20]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
4.3 Resolve Service Center
The Resolve Service Center is responsible for resolving the
destination address of broadcast data packets (such as an IP ARP
packet) to a unicast MAC address to be used in mapping the call
connection. To do this, the Resolve Service Center attempts to
resolve such broadcast packets directly at the access port of the
ingress switch.
Address resolution is accomplished as follows:
1) First, an attempt is made to resolve the address from the switch's
local databases by calling the following servers:
- The Table server attempts to resolve the address from the
Resolve Table (Section 4.3.1).
- Next, the Local server attempts to resolve the address from the
Node and Alias Tables (Section 4.3.2).
- If the address is not found in these tables but is an IP
address, the Resolve Subnet server (Section 4.3.3) is also
called.
2) If the address cannot be resolved locally, the Interswitch Resolve
server (Section 4.3.4) is called to access the "virtual directory"
by sending an Interswitch Resolve request message out over the
switch flood path.
3) If the address cannot be resolved either locally or via an
Interswitch Resolve message -- that is, the destination endstation
is unknown to any switch, perhaps because it has never transmitted
a packet to its switch -- the following steps are taken:
- The Unresolvable server (Section 4.3.5) is called to record the
unresolved packet.
- The Block server (Section 4.3.6) is called to determine whether
the address should be added to the Block Table.
- The Flood Service Center (Section 4.8) is called to broadcast
the packet to other SFVLAN switches using a tag-based flooding
mechanism.
Ruffen, et al. Informational [Page 21]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
4.3.1 Table Server
The Resolve Table server maintains the Resolve Table which contains a
collection of addresses that might not be resolvable in the normal
fashion. This table typically contains such things as the addresses
of "quiet" devices that do not send data packets or special mappings
of IP addresses behind a router. Entries can be added to or deleted
from the Resolve Table via an external management application.
4.3.2 Local Server
The Resolve Local server checks the Node and Alias Tables maintained
by the Directory Service Center (Section 4.1) to determine if it can
resolve the address.
4.3.3 Subnet Server
If the address to be resolved is an IP address but cannot be resolved
via the standard processing described above, the Resolve Subnet
server applies the subnet mask to the IP address and then does a
lookup in the Resolve Table.
4.3.4 Interswitch Resolve Server
If the address cannot be resolved locally, the Interswitch Resolve
server accesses the "virtual directory" by sending an Interswitch
Resolve request message (Section 6.4) out over the switch flood path.
The Interswitch Resolve request message contains the destination
address as it was received within the packet, along with a list of
requested addressing information.
When a switch receives an Interswitch Resolve request message from
one of its upstream neighbors, it checks to see if the destination
endstation is connected to one of its local access ports. If so, it
formulates an Interswitch Resolve response message by filling in the
requested address information, along with its own MAC address. It
then sets the message status field to ResolveAck, and returns the
message to its upstream (requesting) neighbor.
If the receiving switch cannot resolve the address, it forwards the
Interswitch Resolve request message to its downstream neighbors. If
the switch has no downstream neighbors, it sets the message status
field to Unknown, and returns the message to its upstream
(requesting) neighbor.
Ruffen, et al. Informational [Page 22]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
When a switch forwards an Interswitch Resolve request message to its
downstream neighbors, it keeps track of the number of requests it has
sent out and received back. It will only respond back to its
upstream (requesting) neighbor when one of the following conditions
occurs:
- It receives any response with a status of ResolveAck
- All downstream neighbors have responded with a status of Unknown
Any Interswitch Resolve request message that is not responded to
within a certain predetermined time (currently 5 seconds) is assumed
to have a response status of Unknown.
When the Interswitch Resolve server receives a successful Interswitch
Resolve response message, it records the resolved address information
in the remote cache of its local directory for use in resolving later
packets for the same endstation. Note that this process results in
each switch building its own unique copy of the virtual directory
containing only the endstation addresses in which it is interested.
4.3.5 Unresolvable Server
The Unresolvable server is called when a packet destination address
cannot be resolved. The server records the packet in a table that
can then be examined to determine which endstations are generating
unresolvable traffic.
Also, if a particular destination is repeatedly seen to be
unresolvable, the server calls the Block server (Section 4.3.6) to
determine whether the address should be blocked.
4.3.6 Block Server
The Resolve Block server is called when a particular destination has
been repeatedly seen to be unresolvable. This typically happens
when, unknown to the packet source, the destination endstation is
either not currently available or no longer exists.
If the Block server determines that the unresolved address has
exceeded a configurable request threshold, the address is added to
the server's Block Table. Interswitch Resolve request messages for
addresses listed in the Block Table are sent less frequently, thereby
reducing the amount of Interswitch Resolve traffic throughout the
fabric.
Ruffen, et al. Informational [Page 23]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
If an address listed in the Block Table is later successfully
resolved by and Interswitch Resolve request message, the address is
removed from the table.
4.4 Policy Service Center
Once the destination address of the call packet has been resolved,
the Policy Service Center is called to determine the validity of the
requested call connection based on the VLAN policy of the source and
destination VLANs.
4.4.1 Unicast Rules Server
The Policy Unicast Rules server recognizes two VLAN policy values:
Open or Secure. The default policy for all VLANs is Open.
The policy value is used as follows when determining the validity of
a requested call connection:
- If the VLAN policy of either the source or destination cannot be
determined, the Filter Service Center is called to establish a
filter (i.e., blocked) for the SA/DA pair.
- If the source and destination endstations belong to the same VLAN,
then the connection is permitted regardless of the VLAN policy.
- If the source and destination endstations belong to different
VLANs, but both VLANs are running with an Open policy, then the
connection is permitted, providing cut-through switching between
different VLAN(s).
- If the source and destination endstations belong to different
VLANs and one or both of the VLANs are running with a Secure
policy, then the Flood Service Center (Section 4.8) is called to
broadcast the packet to other SFVLAN switches having ports or
endstations that belong to the same VLAN as the packet source.
Note that if any of the VLANs to which the source or destination
belong has a Secure policy, then the policy used in the above
algorithm is Secure.
Ruffen, et al. Informational [Page 24]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
4.5 Connect Service Center
Once the Policy Service Center (Section 4.4) has determined that a
requested call connection is valid, the Connect Service Center is
called to set up the connection. Note that connectivity between two
endstations within the fabric is established on a switch-by-switch
basis as the call progresses through the fabric toward its
destination. No synchronization is needed between switches to
establish an end-to-end connection.
The Connect Service Center maintains a Connection Table containing
information for all connections currently active on the switch's
local ports.
Connections are removed from the Connection Table when one of the
endstations is moved to a new switch (Section 4.1.2) or when the
Topology Link State server (Section 4.2.3) notifies the Connect
Service Center that a network link has failed. Otherwise,
connections are not automatically aged out or removed from the
Connection Table until a certain percentage threshold (HiMark) of
table capacity is reached and resources are needed. At that point,
some number of connections (typically 100) are aged out and removed
at one time.
4.5.1 Local Server
If the destination endstation resides on the local switch, the
Connect Local server establishes a connection between the source and
destination ports. Note that if the source and destination both
reside on the same physical port, a filter connection is established
by calling the Filter Service Center (Section 4.6).
4.5.2 Link State Server
The Connect Link State server is called if the destination endstation
of the proposed connection does not reside on the local switch.
The server executes a call to the Path Link State server (Section
4.7.1) which returns up to three "best" paths of equal cost from the
local switch to the destination switch. If more than one path is
returned, the server chooses a path that provides the best load
balancing of user traffic across the fabric.
Ruffen, et al. Informational [Page 25]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
4.5.3 Directory Server
The Connect Directory server is called if the Connect Link State
server is unable to provide a path for some reason.
The server examines the local directory to determine on which switch
the destination endstation resides. If the port of access to the
destination switch is known, then a connection is established using
that port as the outport of the connection.
4.6 Filter Service Center
The Filter Service Center is responsible for establishing filtered
connections. This service center is called by the Connect Local
server (Section 4.5.1) if the source and destination endstations
reside on the same physical port, and by the Policy Service Center
(Section 4.4) if the VLAN of either the source or destination is
indeterminate.
A filter connection is programmed in the switch hardware with no
specified outport. That is, the connection is programmed to discard
any traffic for that SA/DA pair.
4.7 Path Service Center
The Path Service Center is responsible for determining the path from
a source to a destination.
4.7.1 Link State Server
The Path Link State server is called by the Connect Link State server
(Section 4.5.2) to return up to three best paths of equal cost
between a source and destination pair of endstations. These best
paths are calculated by the Topology Link State server (Section
4.2.3).
The Path Link State server is also called by the Connect Service
Center to return a complete source-to-destination path consisting of
a list of individual switch port names. A switch port name consists
of the switch base MAC address and a port instance relative to the
switch.
Ruffen, et al. Informational [Page 26]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
4.7.2 Spanning Tree Server
The Path Spanning Tree server is called by any server needing to
forward an undirected message out over the switch flood path. The
server returns a port mask indicating which local ports are currently
enabled as outports of the switch flood path. The switch flood path
is calculated by the Topology Spanning Tree server (Section 4.2.2).
4.8 Flood Service Center
If the Resolve Service Center (Section 4.3) is unable to resolve the
destination address of a packet, it invokes the Flood Service Center
to broadcast the unresolved packet.
4.8.1 Tag-Based Flood Server
The Tag-Based Flood server encapsulates the unresolved packet into an
Interswitch Tag-Based Flood message (Section 6.6), along with a list
of Virtual LAN identifiers specifying those VLANs to which the source
endstation belongs. The message is then sent out over the switch
flood path to all other switches in the fabric.
When a switch receives an Interswitch Tag-Based Flood message, it
examines the encapsulated header to determine the VLAN(s) to which
the packet should be sent. If any of the switch's local access ports
belong to one or more of the specified VLANs, the switch strips off
the tag-based header and forwards the original packet out the
appropriate access port(s).
The switch also forwards the entire encapsulated packet along the
switch flood path to its downstream neighboring switches, if any.
5. Monitoring Call Connections
The SecureFast VLAN product permits monitoring of user traffic moving
between two endstations by establishing a call tap on the connection
between the two stations. Traffic can be monitored in one or both
directions along the connection path.
5.1 Definitions
In addition to the terms defined in Section 1.2, the following terms
are used in this description of the call tap process.
Ruffen, et al. Informational [Page 27]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
Originating Switch
The originating switch is the switch that requests the call tap.
Any switch along a call connection path may request a tap on that
call connection.
Probe
The tap probe is the device to receive a copy of the call
connection data. The probe is attached to a port on the probe
switch.
Probe Switch
The probe switch (also known as the terminating switch) is the
switch to which the probe is attached. The probe switch can be
anywhere in the topology.
5.2 Tapping a Connection
A request to tap a call connection between two endstations can
originate on any switch along the call connection path -- the ingress
switch, the egress switch, or any of the intermediate switches. The
call connection must have already been established before a call tap
request can be issued. The probe device can be attached to any
switch in the topology.
5.2.1 Types of Tap Connections
A call tap is enabled by setting up an auxiliary tap connection
associated with the call being monitored. Since the tap must
originate on a switch somewhere along the call connection path, the
tap connection path will pass through one or more of the switches
along the call path. However, since the probe switch can be anywhere
in the switch fabric, the tap path and the call path may diverge at
some point.
Therefore, on each switch along the tap path, the tap connection is
established in one of three ways:
- The existing call connection is used with no modification.
When both the call path and tap path pass through the switch,
and the inport and outports of both connections are identical,
the switch uses the existing call connection to route the tap.
- The existing call connection is modified.
Ruffen, et al. Informational [Page 28]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
When both the call path and tap path pass through the switch,
but the call path outport is different from the tap path
outport, the switch enables an extra outport in either one or
both directions of the call connection, depending on the
direction of the tap. This happens under two conditions.
- If the switch is also the probe switch, an extra outport is
enabled to the probe.
- If the switch is the point at which the call path and the tap path
diverge, an extra outport is enabled to the downstream neighbor
on that leg of the switch flood path on which the probe switch
is located.
- A new connection is established.
If the call path does not pass through the switch (because the
tap path has diverged from the call path), a completely new
connection is established for the tap.
5.2.2 Locating the Probe and Establishing the Tap Connection
To establish a call tap, the originating switch formats an
Interswitch Tap request message (Section 6.7) and sends it out over
the switch flood path to all other switches in the topology.
Note:
If the originating switch is also the probe switch, no
Interswitch Tap request message is necessary.
As the Interswitch Tap request message travels out along the switch
flood path, each switch receiving the message checks to see if it is
the probe switch and does the following:
- If the switch is the probe switch, it establishes the tap
connection by either setting up a new connection or modifying the
call connection, as appropriate (see Section 5.2.1). It then
reformats the Tap request message to be a Tap response message
with a status indicating that the probe has been found, and sends
the message back to its upstream neighbor.
- If the switch is not the probe switch, it forwards the Tap request
message to all its downstream neighbors (if any).
- If the switch is not the probe switch and has no downstream
neighbors, it reformats the Tap request message to be a Tap
response message with a status indicating that the probe is not
Ruffen, et al. Informational [Page 29]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
located on that leg of the switch flood path. It then sends the
response message back to its upstream neighbor.
When a switch forwards an Interswitch Tap request message to its
downstream neighbors, it keeps track of the number of requests it
has sent out.
- If a response is received with a status indicating that the probe
switch is located somewhere downstream, the switch establishes the
appropriate type of tap connection (see Section 5.2.1). It then
formats a Tap response message with a status indicating that the
probe has been found and passes the message to its upstream
neighbor.
- If no responses are received with a status indicating that the
probe switch is located downstream, the switch formats a Tap
response message with a status indicating that the probe has not
been found and passes the message to its upstream neighbor.
5.2.3 Status Field
The status field of the Interswitch Tap request/response message
contains information about the state of the tap. Some of these
status values are transient and are merely used to track the progress
of the tap request. Other status values are stored in the tap table
of each switch along the tap path for use when the tap is torn down.
The possible status values are as follows:
- StatusUnassigned. This is the initial status of the Interswitch
Tap request message.
- OutportDecisionUnknown. The tap request is still moving
downstream along the switch flood path. The probe switch had not
yet been found.
- ProbeNotFound. The probe switch is not located on this leg of the
switch flood path.
- DisableOutport. The probe switch is located on this leg of the
switch flood path, and the switch has had to either modify the
call connection or establish a new connection to implement the tap
(see Section 5.2.1). When the tap is torn down, the switch will
have to disable any additional outports that have been enabled for
the tap.
- KeepOutport. The probe switch is located on this leg of the
switch flood path, and the switch was able to route the tap over
the existing call path (see Section 5.2.1). Any ports used for
Ruffen, et al. Informational [Page 30]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
the tap will remain enabled when the tap is torn down.
5.3 Untapping a Connection
A request to untap a call connection must be issued on the tap
originating switch -- that is, the same switch that issued the tap
request.
To untap a call connection, the originating switch sends an
Interswitch Untap request message (Section 6.7) out over the switch
flood path to all other switches in the topology. The message is
sent over the switch flood path, rather than the tap connection path,
to ensure that all switches that know of the tap are properly
notified, even if the switch topology has changed since the tap was
established.
When a switch receives an Interswitch Untap request message, it
checks to see if it is handling a tap for the specified call
connection. If so, the switch disables the tap connection, as
follows:
- If a new connection was added for the tap, the connection is
deleted from the connection table.
- If additional outports were enabled on the call connection, they
are disabled.
The switch then forwards the Interswitch Untap request message to its
downstream neighbor (if any). If the switch has no downstream
neighbors, it formats an untap response and sends the message back to
its upstream neighbor.
When a switch forwards an Interswitch Untap request message to its
downstream neighbors, it keeps track of the number of requests it has
sent out and does not respond back to its upstream neighbor until all
untap requests have been responded to. Once all responses have been
received, the switch handles any final cleanup for the tap and then
sends a single Interswitch Untap response message to its upstream
neighbor.
Ruffen, et al. Informational [Page 31]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
6. Interswitch Message Protocol (ISMP)
The InterSwitch Message protocol (ISMP) provides a consistent method
of encapsulating and transmitting messages exchanged between switches
to create and maintain the databases and provide other control
services and functionality required by the SFVLAN product.
6.1 General Packet Structure
ISMP packets are of variable length and have the following general
structure:
- Frame header
- ISMP packet header
- ISMP message body
Each of these packet segments is discussed separately in the
following subsections.
6.1.1 Frame Header
ISMP packets are encapsulated within an IEEE 802-compliant frame
using a standard header as shown below:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
00 | |
+ Destination address +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
04 | | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Source address +
08 | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
12 | Type | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
16 | |
+ +
: :
Destination address
This 6-octet field contains the Media Access Control (MAC) address
of the multicast channel over which all switches in the fabric
receive ISMP packets. Except where otherwise noted, this field
Ruffen, et al. Informational [Page 32]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
contains the multicast address of the control channel over which
all switches in the fabric receive ISMP packets -- a value of 01-
00-1D-00-00-00.
Source address
Except where otherwise noted, this 6-octet field contains the
physical (MAC) address of the switch originating the ISMP packet.
Type
This 2-octet field identifies the type of data carried within the
frame. Except where otherwise noted, the type field of ISMP
packets contains the value 0x81FD.
6.1.2 ISMP Packet Header
There are two versions of the ISMP packet header in use by the
SecureFast VLAN product.
6.1.2.1 Version 2
The version 2 ISMP packet header consists of 6 octets, as shown
below:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
00 |///////////////////////////////////////////////////////////////|
://////// Frame header /////////////////////////////////////////:
+//////// (14 octets) /////////+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
12 |///////////////////////////////| Version |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
16 | ISMP message type | Sequence number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
20 | |
+ +
: :
Frame header
This 14-octet field contains the frame header (Section 6.1.1).
Ruffen, et al. Informational [Page 33]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
Version
This 2-octet field contains the version number of the InterSwitch
Message Protocol to which this ISMP packet adheres. This document
describes ISMP Version 2.0.
ISMP message type
This 2-octet field contains a value indicating which type of ISMP
message is contained within the message body. The following table
lists each ISMP message, along with its message type and the
section within this document that describes the message in detail:
Message Name Type Description
Interswitch Link State message 3 See note below
Interswitch BPDU message 4 Section 6.2
Interswitch Remote Blocking message 4 Section 6.3
Interswitch Resolve message 5 Section 6.4
Interswitch New User message 5 Section 6.5
Interswitch Tag-Based Flood message 7 Section 6.6
Interswitch Tap/Untap message 8 Section 6.7
Note:
The Link State messages used by the VLS Protocol are not
described in this document. For a detailed description of
these messages, see [IDvlsp].
Sequence number
This 2-octet field contains an internally generated sequence
number used by the various protocol handlers for internal
synchronization of messages.
6.1.2.2 Version 3
The version 3 ISMP packet header is used only by the Interswitch
Keepalive message. That message is not described in this document.
For a detailed description of the version 3 ISMP packet header, see
[IDhello].
Ruffen, et al. Informational [Page 34]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
6.1.3 ISMP Message Body
The ISMP message body is a variable-length field containing the
actual data of the ISMP message. The length and content of this
field are determined by the value found in the message type field.
See the following sections for the exact format of each message type.
6.2 Interswitch BPDU Message
The Interswitch BPDU message consists of a variable number of octets,
as shown below:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
00 | |
+ Frame header / +
: ISMP packet header (type 4) :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
20 | Version | Opcode |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
24 | Message flags | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
28 | |
: BPDU packet :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Frame header/ISMP packet header
This 20-octet field contains the frame header and the ISMP packet
header.
Version
This 2-octet field contains the version number of the message
type. This document describes ISMP message type 4, version 1.
Ruffen, et al. Informational [Page 35]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
Opcode
This 2-octet field contains the operation type of the message. For
an Interswitch BPDU message, the value should be 1.
Message flags
This 2-octet field is currently unused. It is reserved for future
use.
BPDU packet
This variable-length field contains an IEEE-compliant 802.2 Bridge
Protocol Data Unit. See [IEEE] for a detailed description of the
contents of this field.
6.3 Interswitch Remote Blocking Message
The Interswitch Remote Blocking message consists of 30 octets, as
shown below:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
00 | |
+ Frame header / +
: ISMP packet header (type 4) :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
20 | Version | Opcode |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
24 | Message flags | Blocking flag ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
28 | ... Blocking flag |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Frame header/ISMP packet header
This 20-octet field contains the frame header and the ISMP packet
header.
Version
This 2-octet field contains the version number of the message
type. This document describes ISMP message type 4, version 1.
Ruffen, et al. Informational [Page 36]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
Opcode
This 2-octet field contains the operation type of the message.
Valid values are as follows:
2 Enable/disable remote blocking
3 Acknowledge previously received Remote Blocking message
Message flags
This 2-octet field is currently unused. It is reserved for
future use.
Blocking flag
This 4-octet field contains a flag indicating the state of
remote blocking on the link over which the message was
received. A value of 1 indicates remote blocking is on and no
undirected ISMP messages should be sent over the link. A value
of 0 indicates remote blocking is off. This flag is irrelevant
if the operation type (Opcode) of the message has a value of 3.
6.4 Interswitch Resolve Message
There are two versions of the Interswitch Resolve message used by the
SecureFast VLAN product.
6.4.1 Prior to Version 1.8
The Interswitch Resolve message used by SFVLAN prior to version 1.8
consists of a variable number of octets, as shown below:
Ruffen, et al. Informational [Page 37]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
00 | |
+ Frame header / +
: ISMP packet header (type 5) :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
20 | Version | Opcode |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
24 | Status | Call Tag |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
28 | |
+ Source MAC of packet +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
32 | | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Originating switch MAC +
36 | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
40 | |
+ Owner switch MAC +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
44 | | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
48 | |
: Known destination address :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
n | Count | |
+-+-+-+-+-+-+-+-+ +
n+4 | Resolve list |
: :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
n = 46 + length of known address TLV
In the following description of the message fields, the term
"originating" switch refers to the switch that issued the original
Interswitch Resolve request. The term "owner" switch refers to that
switch to which the destination endstation is attached. And the term
"responding" switch refers to either the "owner" switch or to a
switch at the end of the switch flood path that does not own the
endstation but issues an Interswitch Resolve response because it has
no downstream neighbors.
Ruffen, et al. Informational [Page 38]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
With the exception of the resolve list (which has a different size
and format in a Resolve response message), all fields of an
Interswitch Resolve message are allocated by the originating switch,
and unless otherwise noted below, are written by the originating
switch.
Frame header/ISMP packet header
This 20-octet field contains the frame header and the ISMP packet
header.
Version
This 2-octet field contains the version number of the message
type. This document describes ISMP message type 5, version 1.
Opcode
This 2-octet field contains the operation code of the message.
Valid values are as follows:
1 The message is a Resolve request.
2 The message is a Resolve response.
3 (unused in Resolve messages)
4 (unused in Resolve messages)
The originating switch writes a value of 1 to this field, while
the responding switch writes a value of 2.
Status
This 2-octet field contains the status of a Resolve response
message. Valid values are as follows:
0 The Resolve request succeeded (ResolveAck).
1 (unused)
2 The Resolve request failed (Unknown).
This field is written by the responding switch.
Call tag
This 2-octet field contains the call tag of the endstation packet
for which this Resolve request is issued. The call tag is a 16-
bit value (generated by the originating switch) that uniquely
identifies the packet.
Ruffen, et al. Informational [Page 39]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
Source MAC of packet
This 6-octet field contains the physical (MAC) address of the
endstation that originated the packet identified by the call tag.
Originating switch MAC
This 6-octet field contains the physical (MAC) address of the
switch that issued the original Resolve request.
Owner switch MAC
This 6-octet field contains the physical (MAC) address of the
switch to which the destination endstation is attached -- that is,
the switch that was able to resolve the requested addressing
information. This field is written by the owner switch.
If the status of the response is Unknown, this field is
irrelevant.
Known destination address
This variable-length field contains the known attribute of the
destination endstation address. This address is stored in
Tag/Length/Value format. (See Section 2.3.)
Count
This 1-octet field contains the number of address attributes
requested or returned. This is the number of items in the resolve
list.
Resolve list
This variable-length field contains a list of the address
attributes either requested by the originating switch or returned
by the owner switch. Note that in a Resolve request message, this
list contains only the tags of the requested address attributes
(see Section 2.3). On the other hand, a Resolve response message
with a status of ResolveAck contains the full TLV of each resolved
address attribute. The number of entries in the list is specified
in the count field.
In an Interswitch Resolve response message, this field is
irrelevant if the status of the response is Unknown.
Ruffen, et al. Informational [Page 40]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
6.4.2 Version 1.8
The Interswitch Resolve message used by SFVLAN version 1.8 consists
of a variable number of octets, as shown below:
Ruffen, et al. Informational [Page 41]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
00 | |
+ Frame header / +
: ISMP packet header (type 5) :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
20 | Version | Opcode |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
24 | Status | Call Tag |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
28 | |
+ Source MAC of packet +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
32 | | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Originating switch MAC +
36 | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
40 | |
+ Owner switch MAC +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
44 | | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
48 | |
: Known destination address :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
n | Count | |
+-+-+-+-+-+-+-+-+ +
n+4 | Resolve list |
: :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
n1 | |
+ Actual dest switch MAC +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Downlink chassis MAC +
n1+8 | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
n1+12 | |
+ Actual chassis MAC +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
n1+20 | |
+ Domain name +
: :
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
n = 46 + length of known address TLV
n1 = n + length of Resolve list
Ruffen, et al. Informational [Page 42]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
In the following description of the message fields, the term
"originating" switch refers to the switch that issued the original
Interswitch Resolve request. The term "owner" switch refers to that
switch to which the destination endstation is attached. And the term
"responding" switch refers to either the "owner" switch or to a
switch at the end of the switch flood path that does not own the
endstation but issues an Interswitch Resolve response because it has
no downstream neighbors.
With the exception of the resolve list (which has a different size
and format in a Resolve response message) and the four fields
following the resolve list, all fields of an Interswitch Resolve
message are allocated by the originating switch, and unless otherwise
noted below, are written by the originating switch.
Frame header/ISMP packet header
This 20-octet field contains the frame header and the ISMP packet
header.
Version
This 2-octet field contains the version number of the message
type. This section describes version 3 of the Interswitch Resolve
message.
Opcode
This 2-octet field contains the operation code of the message.
Valid values are as follows:
1 The message is a Resolve request.
2 The message is a Resolve response.
3 (unused in Resolve messages)
4 (unused in Resolve messages)
The originating switch writes a value of 1 to this field, while
the responding switch writes a value of 2.
Ruffen, et al. Informational [Page 43]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
Status
This 2-octet field contains the status of a Resolve response
message. Valid values are as follows:
0 The Resolve request succeeded (ResolveAck).
1 (unused)
2 The Resolve request failed (Unknown).
This field is written by the responding switch.
Call tag
This 2-octet field contains the call tag of the endstation packet
for which this Resolve request is issued. The call tag is a 16-
bit value (generated by the originating switch) that uniquely
identifies the packet.
Source MAC of packet
This 6-octet field contains the physical (MAC) address of the
endstation that originated the packet identified by the call tag.
Originating switch MAC
This 6-octet field contains the physical (MAC) address of the
switch that issued the original Resolve request.
Owner switch MAC
This 6-octet field contains the physical (MAC) address of the
switch to which the destination endstation is attached -- that is,
the switch that was able to resolve the requested addressing
information. This field is written by the owner switch.
If the status of the response is Unknown, this field is
irrelevant.
Known destination address
This variable-length field contains the known attribute of the
destination endstation address. This address is stored in
Tag/Length/Value format.
Ruffen, et al. Informational [Page 44]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
Count
This 1-octet field contains the number of address attributes
requested or returned. This is the number of items in the resolve
list.
Resolve list
This variable-length field contains a list of the address
attributes either requested by the originating switch or returned
by the owner switch. Note that in a Resolve request message, this
list contains only the tags of the requested address attributes.
On the other hand, a Resolve response message with a status of
ResolveAck contains the full TLV of each resolved address
attribute. The number of entries in the list is specified in the
count field.
In an Interswitch Resolve response message, this field is
irrelevant if the status of the response is Unknown.
Actual destination switch MAC
This 6-octet field contains the physical (MAC) address of the
actual switch within the chassis to which the endstation is
attached. If the status of the response is Unknown, this field is
irrelevant.
Downlink chassis MAC
This 6-octet field contains the physical (MAC) address of the
downlink chassis. If the status of the response is Unknown, this
field is irrelevant.
Actual chassis MAC
This 6-octet field contains the physical (MAC) address of the
uplink chassis. If the status of the response is Unknown, this
field is irrelevant.
Domain name
This 16-octet field contains the ASCII name of the domain. If the
status of the response is Unknown, this field is irrelevant.
Ruffen, et al. Informational [Page 45]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
6.5 Interswitch New User Message
The Interswitch New User message consists of a variable number of
octets, as shown below:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
00 | |
+ Frame header / +
: ISMP packet header (type 5) :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
20 | Version | Opcode |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
24 | Status | Call Tag |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
28 | |
+ Source MAC of packet +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
32 | | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Originating switch MAC +
36 | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
40 | |
+ Previous owner switch MAC +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
44 | | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
48 | :
: MAC address of new user +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
70 | Count | |
+-+-+-+-+-+-+-+-+ +
74 | Resolve list |
: :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
In the following description of the message fields, the term
"originating" switch refers to the switch that issued the original
Interswitch New User request. The term "previous owner" switch
refers to that switch to which the endstation was previously
attached. And the term "responding" switch refers to either the
"previous owner" switch or to a switch at the end of the switch flood
path that did not own the endstation but issues an Interswitch New
User response because it has no downstream neighbors.
Ruffen, et al. Informational [Page 46]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
With the exception of the resolve list, all fields of an Interswitch
New User message are allocated by the originating switch, and unless
otherwise noted below, are written by the originating switch.
Frame header/ISMP packet header
This 20-octet field contains the frame header and the ISMP packet
header.
Version
This 2-octet field contains the version number of the message
type. This document describes ISMP message type 5, version 1.
Opcode
This 2-octet field contains the operation code of the message.
Valid values are as follows:
1 (unused in a New User message)
2 (unused in a New User message)
3 The message is a New User request.
4 The message is a New User response.
The originating switch writes a value of 3 to this field, while
the responding switch writes a value of 4.
Status
This 2-octet field contains the status of a New User response
message. Valid values are as follows:
0 VLAN resolution successful (NewUserAck)
1 (unused)
2 VLAN resolution unsuccessful (NewUserUnknown)
This field is written by the responding switch.
Call tag
This 2-octet field contains the call tag of the endstation packet
for which this New User request is issued. The call tag is a 16-
bit value (generated by the originating switch) that uniquely
identifies the packet that caused the switch to identify the
endstation as a new user.
Ruffen, et al. Informational [Page 47]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
Source MAC of packet
This 6-octet field contains the physical (MAC) address of the
endstation that originated the packet identified by the call tag.
Originating switch MAC
This 6-octet field contains the physical (MAC) address of the
switch that issued the original New User request.
Previous owner switch MAC
This 6-octet field contains the physical (MAC) address of the
switch to which the endstation was previously attached -- that is,
the switch that was able to resolve the VLAN information. This
field is written by the previous owner switch.
If the status of the response is Unknown, this field is
irrelevant.
MAC address of new user
This 24-octet field contains the physical (MAC) address of the new
user endstation, stored in Tag/Length/Value format.
Count
This 1-octet field contains the number of VLAN identifiers
returned. This is the number of items in the resolve list. This
field is written by the previous owner switch.
If the status of the response is Unknown, this field and the
resolve list are irrelevant.
Resolve list
This variable-length field contains a list of the VLAN identifiers
of all static VLANs to which the endstation belongs, stored in
Tag/Length/Value format (see Section 2.3). The number of entries
in the list is specified in the count field. This list is written
by the previous owner switch.
If the status of the response is Unknown, this field is
irrelevant.
Ruffen, et al. Informational [Page 48]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
6.6 Interswitch Tag-Based Flood Message
There are two versions of the Interswitch Tag-Based Flood message
used by the SecureFast VLAN product.
6.6.1 Prior to Version 1.8
The Interswitch Tag-Based Flood message used by SFVLAN prior to
version 1.8 consists of a variable number of octets, as shown below:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
00 | |
+ Frame header / +
: ISMP packet header (type 7) :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
20 | Version | Opcode |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
24 | Status | Call Tag |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
28 | |
+ Source MAC of packet +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
32 | | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Originating switch MAC +
36 | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
40 | Count | |
+-+-+-+-+-+-+-+-+ +
44 | VLAN list |
: :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
n | |
+ +
: Original packet :
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
n = 41 + length of VLAN list
Ruffen, et al. Informational [Page 49]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
Frame header/ISMP packet header
This 20-octet field contains the frame header and the ISMP packet
header.
Version
This 2-octet field contains the version number of the message
type. This document describes ISMP message type 7, version 1.
Opcode
This 2-octet field contains the operation code of the message. The
value here should be 1, indicating the message is a flood request.
Status
This 2-octet field is currently unused. It is reserved for future
use.
Call tag
This 2-octet field contains the call tag of the endstation packet
encapsulated within this tag-based flood message. The call tag is
a 16-bit value (generated by the originating switch) that uniquely
identifies the packet.
Source MAC of packet
This 6-octet field contains the physical (MAC) address of the
endstation that originated the packet identified by the call tag.
Originating switch MAC
This 6-octet field contains the physical (MAC) address of the
switch that issued the original tag-based flooded message.
Count
This 1-octet field contains the number of VLAN identifiers
included in the VLAN list.
VLAN list
This variable-length field contains a list of the VLAN identifiers
of all VLANs to which the source endstation belongs. Each entry
in this list has the following format:
Ruffen, et al. Informational [Page 50]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value length | |
+-+-+-+-+-+-+-+-+ +
| VLAN identifier value |
: :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The 1-octet value length field contains the length of the VLAN
identifier. VLAN identifiers can be from 1 to 16 characters long.
Original packet
This variable-length field contains the original packet as sent by
the source endstation.
Ruffen, et al. Informational [Page 51]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
6.6.2 Version 1.8
The Interswitch Tag-Based Flood message used by SFVLAN version 1.8
consists of a variable number of octets, as shown below:
Note:
SFVLAN version 1.8 also recognizes the Interswitch Tag-Based
Flood message as described in Section 6.6.1.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
00 | |
+ Frame header / +
: ISMP packet header (type 7) :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
20 | VLAN identifier | Version |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
24 | Opcode | Status |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
28 | Call tag | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Source MAC of packet +
32 | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
36 | |
+ Originating switch MAC +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
40 | | Count | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
44 | |
: VLAN list :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
n | |
+ +
: Original packet :
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
n = 41 + length of VLAN list
Frame header/ISMP packet header
This 20-octet field contains the frame header and the ISMP packet
header.
Ruffen, et al. Informational [Page 52]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
- The frame header source address contains a value of 02-00-1D-
00-xx-yy, where xx-yy is a value set by the VLAN Manager
application to tag the frame header with the VLAN identifier.
This value ranges from 2 to 4095. For example, a value of 100
would be set as 00-64.
- The frame header type field contains a value of 0x81FF. Note
that this differs from all other ISMP messages.
VLAN identifier
This 2-octet field contains the VLAN identifier of the packet
source.
Version
This 2-octet field contains the version number of the message
type. This section describes version 2 of the Interswitch Tag-
Based Flood message.
Opcode
This 2-octet field contains the operation code of the message.
Valid values here are as follows:
1 The message is a flood request. The original packet is
complete within this message.
2 The message is a fragmented flood request. The first portion
of the original packet is contained in this message.
3 The message is a fragmented flood request. The second portion
of the original packet is contained in this message.
Status
This 2-octet field is currently unused. It is reserved for future
use.
Call tag
This 2-octet field contains the call tag of the endstation packet
encapsulated within this tag-based flood message. The call tag is
a 16-bit value (generated by the originating switch) that uniquely
identifies the packet.
Ruffen, et al. Informational [Page 53]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
Source MAC of packet
This 6-octet field contains the physical (MAC) address of the
endstation that originated the packet identified by the call tag.
Originating switch MAC
This 6-octet field contains the physical (MAC) address of the
switch that issued the original tag-based flooded message.
Count
This 1-octet field contains the number of VLAN identifiers
included in the VLAN list.
VLAN list
This variable-length field contains a list of the VLAN identifiers
of all VLANs to which the source endstation belongs. Each entry
in this list has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value length | |
+-+-+-+-+-+-+-+-+ +
| VLAN identifier value |
: :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The 1-octet value length field contains the length of the VLAN
identifier. VLAN identifiers can be from 1 to 16 characters long.
Original packet
This variable-length field contains the original packet as sent by
the source endstation.
Ruffen, et al. Informational [Page 54]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
6.7 Interswitch Tap/Untap Message
The Interswitch Tap/Untap message consists of a variable number of
octets, as shown below:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
00 | |
+ Frame header / +
: ISMP packet header (type 8) :
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
20 | Version | Opcode |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
24 | Status | Error code |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
28 | Header type | Header length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
32 | Direction | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Probe switch MAC +
36 | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
40 | Probe port |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
44 | |
+ +
48 | (Reserved) |
+ +
52 | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
56 | |
+ +
| Header |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Frame header/ISMP packet header
This 20-octet field contains the frame header and the ISMP packet
header.
Version
This 2-octet field contains the version number of the message
type. This document describes ISMP message type 8, version 1.
Ruffen, et al. Informational [Page 55]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
Opcode
tet field contains the operation type of the message. ues are as
follows:
1 The message is a Tap request.
2 The message is a Tap response.
3 The message is an Untap request.
4 The message is an Untap response.
Status
This 2-octet field contains the current status of the tap request.
Valid values are as follows:
1 Switch must disable outport on untap. (DisableOutport)
2 Switch must keep outports on untap. (KeepOutport)
3 Probe not found this leg of spanning tree. (ProbeNotFound)
4 Still searching for probe switch. (OutportDecisionUnknown)
5 Unassigned. (StatusUnassigned)
6 (reserved)
7 (reserved)
8 (reserved)
9 (reserved)
See Section 5.2.3 for details on the use of this field.
Error code
This 2-octet field contains the response message error code of the
requested operation. Valid values are as follows:
1 Operation successful. (NoError)
2 No response heard from downstream neighbor. (Timeout)
3 Port does not exist on probe switch. (BadPort)
4 Message invalid. (InvalidMessage)
5 Version number invalid. (IncompatibleVersions)
Header type
This 2-octet field contains the type of information contained in
the header field. Currently, valid values are as follows:
1 (reserved) 2 Header contains destination and source endstation
MAC addresses.
Ruffen, et al. Informational [Page 56]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
Header length
This 2-octet field contains the length of the header field.
Currently, this field always contains a value of 12.
Direction
This 2-octet field contains a value indicating the type of tap.
Valid values are as follows:
1 (reserved)
2 Tap is bi-directional and data should be captured flowing in
either direction over the connection.
3 Tap is uni-directional and data should be captured only when it
flows from the source to the destination.
Probe switch MAC
This 6-octet field contains the physical (MAC) address of the
switch to which the probe is attached.
Probe port
This 4-octet field contains the logical port number (on the probe
switch) to which the probe is attached.
Reserved
These 12 octets are reserved.
Header
This variable-length field contains the header that identifies the
connection being tapped. The length of the header is stored in
the length field.
Currently, this field is 12 octets long and contains the 6-octet
physical address of the connection's destination endstation,
followed by the 6-octet physical address of the connection's
source endstation, as shown below:
Ruffen, et al. Informational [Page 57]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ Destination MAC address +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Source MAC address +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
7. Security Considerations
Requested call connections are established or denied based on the
VLAN policy of the source and destination addresses specified within
the packet. Section 4.4.1 discusses this process in detail.
8. References
[RFC1700] Reynolds, J. and J. Postel, "Assigned Numbers", STD 2,
RFC 1700, October 1994.
[IEEE] "IEEE Standard 802.1d -- 1990"
[IDvlsp] Kane, L., "Cabletron's VLS Protocol Specification", RFC
2642, August 1999.
[IDhello] Hamilton, D. and D. Ruffen, "Cabletron's VlanHello
Protocol Specification", RFC 2641, August 1999.
Ruffen, et al. Informational [Page 58]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
9. Authors' Addresses
Dave Ruffen
Cabletron Systems, Inc.
Post Office Box 5005
Rochester, NH 03866-5005
Phone: (603) 332-9400
EMail: ruffen@ctron.com
Ted Len
Cabletron Systems, Inc.
Post Office Box 5005
Rochester, NH 03866-5005
Phone: (603) 332-9400
EMail: len@ctron.com
Judy Yanacek
Cabletron Systems, Inc.
Post Office Box 5005
Rochester, NH 03866-5005
Phone: (603) 332-9400
EMail: jyanacek@ctron.com
Ruffen, et al. Informational [Page 59]
RFC 2643 Cabletron's SecureFast VLAN Operational Model August 1999
10. Full Copyright Statement
Copyright (C) The Internet Society (1999). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Ruffen, et al. Informational [Page 60]