Network Working Group S . Herzog, Ed.
Request for Comments: 2749 IPHighway
Category: Standards Track J. Boyle
Level3
R. Cohen
Cisco
D. Durham
Intel
R. Rajan
AT&T
A. Sastry
Cisco
January 2000
COPS usage for RSVP
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2000). All Rights Reserved.
Abstract
This document describes usage directives for supporting COPS policy
services in RSVP environments.
Table of Contents
1 Introduction....................................................2
2 RSVP values for COPS objects....................................2
2.1 Common Header, client-type...................................2
2.2 Context Object (Context).....................................3
2.3 Client Specific Information (ClientSI).......................4
2.4 Decision Object (Decision)...................................4
3 Operation of COPS for RSVP PEPs.................................6
3.1 RSVP flows...................................................6
3.2 Expected Associations for RSVP Requests......................6
3.3 RSVP's Capacity Admission Control: Commit and Delete.........7
3.4 Policy Control Over PathTear and ResvTear....................7
Herzog, et al. Standards Track [Page 1]
RFC 2749 COPS usage for RSVP January 2000
3.5 PEP Caching COPS Decisions...................................7
3.6 Using Multiple Context Flags in a single query...............8
3.7 RSVP Error Reporting.........................................9
4 Security Considerations.........................................9
5 Illustrative Examples, Using COPS for RSVP......................9
5.1 Unicast Flow Example.........................................9
5.2 Shared Multicast Flows......................................11
6 References.....................................................14
7 Author Information and Acknowledgments.........................15
8 Full Copyright Statement.......................................17
1 Introduction
The Common Open Policy Service (COPS) protocol is a query response
protocol used to exchange policy information between a network policy
server and a set of clients [COPS]. COPS is being developed within
the RSVP Admission Policy Working Group (RAP WG) of the IETF,
primarily for use as a mechanism for providing policy-based admission
control over requests for network resources [RAP].
This document is based on and assumes prior knowledge of the RAP
framework [RAP] and the basic COPS [COPS] protocol. It provides
specific usage directives for using COPS in outsourcing policy
control decisions by RSVP clients (PEPs) to policy servers (PDPs).
Given the COPS protocol design, RSVP directives are mainly limited to
RSVP applicability, interoperability and usage guidelines, as well as
client specific examples.
2 RSVP values for COPS objects
The usage of several COPS objects is affected when used with the RSVP
client type. This section describes these objects and their usage.
2.1 Common Header, client-type
RSVP is COPS client-type 1
Herzog, et al. Standards Track [Page 2]
RFC 2749 COPS usage for RSVP January 2000
2.2 Context Object (Context)
The semantics of the Context object for RSVP is as follows:
R-Type (Request Type Flag)
Incoming-Message request
This context is used when the PEP receives an incoming RSVP
message. The PDP may decide to accept or reject the incoming
message and may also apply other decision objects to it. If the
incoming message is rejected, RSVP should treat it as if it
never arrived.
Resource-Allocation request
This context is used when the PEP is about to commit local
resources to an RSVP flow (admission control). This context
applies to Resv messages only. The decision whether to commit
local resources is made for the merge of all reservations
associated with an RSVP flow (which have arrived on a
particular interface, potentially from several RSVP Next-Hops).
Outgoing-Message request (forwarding an outgoing RSVP message)
This context is used when the PEP is about to forward an
outgoing RSVP message. The PDP may decide to allow or deny the
outgoing message, as well as provide an outgoing policy data
object.
M-Type (Message Type)
The M-Type field in the Context Object identifies the applicable RSVP
message type. M-Type values are identical to the values used in the
"msg type" field in the RSVP header [RSVP].
The following RSVP message types are supported in COPS:
Path
Resv
PathErr
ResvErr
Other message types such as PathTear, ResvTear, and Resv Confirm are
not supported. The list of supported message types can only be
extended in later versions of RSVP and/or later version of this
document.
Herzog, et al. Standards Track [Page 3]
RFC 2749 COPS usage for RSVP January 2000
2.3 Client Specific Information (ClientSI)
All objects that were received in an RSVP message are encapsulated
inside the Client Specific Information Object (Signaled ClientSI)
sent from the PEP to the remote PDP (see Section 3.1. on multiple
flows packed in a single RSVP message).
The PEP and PDP share RSVP state, and the PDP is assumed to implement
the same RSVP functional specification as the PEP. In the case where
a PDP detects the absence of objects required by [RSVP] it should
return an <Error> in the Decision message indicating "Mandatory
client-specific info missing". If, on the other hand, the PDP detects
the absence of optional RSVP objects that are needed to approve the
Request against current policies, the PDP should return a negative
<Decision>.
Unlike the Incoming and Outgoing contexts, "Resource Allocation" is
not always directly associated with a specific RSVP message. In a
multicast session, it may represent the merging of multiple incoming
reservations. Therefore, the ClientSI object should specifically
contain the SESSION and STYLE objects along with the merged FLOWSPEC,
FILTERSPEC list, and SCOPE object (whenever relevant).
2.4 Decision Object (Decision)
COPS provides the PDP with flexible controls over the PEP using
RSVP's response to messages. While accepting an RSVP message, PDPs
may provide preemption priority, trigger warnings, replace RSVP
objects, and much more, using Decision Commands, Flags, and Objects.
DECISION COMMANDS
Only two commands apply to RSVP
Install
Positive Response:
Accept/Allow/Admit an RSVP message or local resource allocation.
Remove
Negative Response:
Deny/Reject/Remove an RSVP message or local resource allocation.
Herzog, et al. Standards Track [Page 4]
RFC 2749 COPS usage for RSVP January 2000
DECISION FLAGS
The only decision flag that applies to RSVP:
Trigger Error
If this flag is set, RSVP should schedule a PathErr, in response
to a Path message, or a ResvErr (in response of a Resv message).
STATELESS POLICY DATA
This object may include one or more policy elements (as specified for
the RSVP Policy Data object [RSVP-EXT]) which are assumed to be well
understood by the client's LPDP. The PEP should consider these as an
addition to the decision already received from the PDP (it can only
add, but cannot override it).
For example, given Policy Elements that specify a flow's preemption
priority, these elements may be included in an incoming Resv message
or may be provided by the PDP responding to a query.
Stateless objects must be well understood, but not necessarily
supported by all PEPs. For example, assuming a standard policy
element for preemption priority, it is perfectly legitimate for some
PEPs not to support such preemption and to ignore it. The PDP must be
careful when using such objects. In particular, it must be prepared
for these objects to be ignored by PEPs.
Stateless Policy Data may be returned in decisions and apply
individually to each of the contexts flagged in REQ messages. When
applied to Incoming, it is assumed to have been received as a
POLICY_DATA object in the incoming message. When applied to Resource
Allocation it is assumed to have been received on all merged incoming
messages. Last, when applied to outgoing messages it is assumed to
have been received in all messages contributing to the outgoing
message.
REPLACEMENT DATA
The Replacement object may contain multiple RSVP objects to be
replaced (from the original RSVP request). Typical replacement is
performed on the "Forward Outgoing" request (for instance, replacing
outgoing Policy Data), but is not limited, and can also be performed
on other contexts (such as "Resources-Allocation Request"). In other
cases, replacement of the RSVP FlowSpec object may be useful for
controlling resources across a trusted zone (with policy ignorant
Herzog, et al. Standards Track [Page 5]
RFC 2749 COPS usage for RSVP January 2000
nodes (PINs). Currently, RSVP clients are only required to allow
replacement of three objects: POLICY_DATA, ERROR_SPEC, and FLOWSPEC,
but could optionally support replacement of other objects.
RSVP object replacement is performed in the following manner:
If no Replacement Data decision appears in a decision message, all
signaled objects are processed as if the PDP was not there. When an
object of a certain C-Num appears, it replaces ALL the instances of
C-Num objects in the RSVP message. If it appears empty (with a length
of 4) it simply removes all instances of C-Num objects without adding
anything.
3 Operation of COPS for RSVP PEPs
3.1 RSVP flows
Policy Control is performed per RSVP flow, which is defined by the
atomic unit of an RSVP reservation (TC reservation). Reservation
styles may also impact the definition of flows; a set of senders
which are considered as a single flow for WF reservation are
considered as a set of individual flows when FF style is used.
Multiple FF flows may be packed into a single Resv message. A packed
message must be unpacked where a separate request is issued for each
of the packed flows as if they were individual RSVP messages. Each
COPS Request should include the associated POLICY_DATA objects, which
are, by default, all POLICY_DATA objects in the packed message.
Sophisticated PEPs, capable of looking inside policy objects, may
examine the POLICY_DATA or SCOPE object to narrow down the list of
associated flows (as an optimization).
Please note that the rules governing Packed RSVP message apply
equally to the Incoming as well as the Outgoing REQ context.
3.2 Expected Associations for RSVP Requests
When making a policy decision, the PDP may consider both Resv as well
as its matching Path state (associated state). State association is
straightforward in the common unicast case since the RSVP flow
includes one Path state and one Resv state. In multicast cases this
correspondence may be more complicated, as the match may be many-to-
many. The COPS protocol assumes that the PDP is RSVP knowledgeable
and capable of determining these associations based on the contents
of the Client REQ message and especially the ClientSI object.
Herzog, et al. Standards Track [Page 6]
RFC 2749 COPS usage for RSVP January 2000
For example, the PDP should be able to recognize activation and
deactivation of RSVP blockade state following discrete events like
the arrival of a ResvErr message (activate the blockade state) as
well as the change in the outgoing Resv message.
3.3 RSVP's Capacity Admission Control: Commit and Delete
In RSVP, the admission of a new reservation requires both an
administrative approval (policy control) and capacity admission
control. After being approved by both, and after the reservation was
successfully installed, the PEP notifies the remote PDP by sending a
report message specifying the Commit type. The Commit type report
message signals when billing should effectively begin and performing
heavier delayed operations (e.g., debiting a credit card) is
permissible by the PDP.
If, instead, a PDP approved reservation fails admission due to lack
of resources, the PEP must issue a no-commit report and fold back and
send an updated request to its previous state (previously installed
reservation). If no state was previously installed, the PEP should
issue a delete (DRQ).
3.4 Policy Control Over PathTear and ResvTear
PathTear and ResvTear messages are not controlled by this policy
architecture. This relies on two assumptions: First, that MD-5
authentication verifies that the Tear is received from the same node
that sent the initial reservation, and second, that it is
functionally equivalent to that node holding off refreshes for this
reservation. When a ResvTear or PathTear is received at the PEP, all
affected states installed on the PDP should either be deleted or
updated by the PEP.
3.5 PEP Caching COPS Decisions
Because COPS is a stateful protocol, refreshes for RSVP Path and Resv
messages need not be constantly sent to the remote PDP. Once a
decision has been returned for a request, the PEP can cache that
decision and apply it to future refreshes. When the PEP detects a
change in the corresponding Resv or Path message, it should update
the PDP with the new request-state. PEPs may continue to use the
cached state until receiving the PDP response. This case is very
different from initial admission of a flow; given that valid
credentials and authentication have already been established, the
relatively long RSVP refresh period, and the short PEP-PDP response
time, the tradeoff between expedient updates and attack prevention
leans toward expediency. However, this is really a PEP choice, and is
irrelevant to PDPs.
Herzog, et al. Standards Track [Page 7]
RFC 2749 COPS usage for RSVP January 2000
If the connection is lost between the PEP and the PDP, the cached
RSVP state may be retained for the RSVP timeout period to be used for
previously admitted flows (but cannot be applied to new or updated
state). If the connection can not be reestablished with the PDP or a
backup PDP after the timeout period, the PEP is expected to purge all
its cached decisions. Without applicable cached decision, the PEP
must either reject the flow or resort to its LPDP (if available) for
decisions.
Once a connection is reestablished to a new (or the original) PDP the
PDP may issue a SSQ request. In this case, the PEP must reissue
requests that correspond to the current RSVP state (as if all the
state has been updated recently). It should also include in its
LPDPDecision the current (cached) decision regarding each such state.
3.6 Using Multiple Context Flags in a single query
RSVP is a store-and-forward control protocol where messages are
processed in three distinctive steps (input, resource allocation, and
output). Each step requires a separate policy decision as indicated
by context flags (see Section 2.2). In many cases, setting multiple
context flags for bundling two or three operations together in one
request may significantly optimize protocol operations.
The following rules apply for setting multiple Context flags:
a. Multiple context flags can be set only in two generic cases, which
represent a substantial portion of expected COPS transactions, and
can be guaranteed not to cause ambiguity.
Unicast FF:
[Incoming + Allocation + Outgoing]
Multicast with only one Resv message received on the interface
[Incoming + Allocation]
b. Context events are ordered by time since every message must first
be processed as Incoming, then as Resource allocation and only
then as Outgoing. When multiple context flags are set, all
ClientSI objects included in the request are assumed to be
processed according to the latest flag. This rule applies both to
the request (REQ) context as well as to the decision (DEC)
context.
Herzog, et al. Standards Track [Page 8]
RFC 2749 COPS usage for RSVP January 2000
For example, when combining Incoming + Allocation for an incoming
Resv message, the flowspec included in the ClientSI would be the
one corresponding to the Resource-Allocation context (TC).
c. Each decision is bound to a context object, which determines which
portion of the request context it applies to. When individual
decisions apply to different sub-groups of the context, the PDP
should send each group of decision objects encapsulated by the
context flags object with the context flags applicable to these
objects set (see the examples in Section 5).
3.7 RSVP Error Reporting
RSVP uses the ERROR_SPEC object in PathErr and ResvErr messages to
report policy errors. While the contents of the ERROR_SPEC object are
defined in [RSVP,RSVP-EXT], the PDP is in the best position to
provide its contents (sub-codes). This is performed in the following
manner: First, the PEP (RSVP) queries the PDP before sending a
PathErr or ResvErr, and then the PDP returns the constructed
ERROR_SPEC in the Replacement Data Decision Object.
4 Security Considerations
This document relies on COPS for its signaling and its security.
Please refer to section "Security Considerations" in [COPS].
Security for RSVP messages is provided by inter-router MD5
authentication [MD5], assuming a chain-of-trust model. A likely
deployment scenario calls for PEPs to be deployed only at the network
edge (boundary nodes) while the core of the network (backbone)
consists of PIN nodes. In this scenario MD5 trust (authentication) is
established between boundary (non-neighboring) PEPs. Such trust can
be achieved through internal signing (integrity) of the Policy Data
object itself, which is left unmodified as it passes through PIN
nodes (see [RSVP-EXT]).
5 Illustrative Examples, Using COPS for RSVP
This section details both typical unicast and multicast scenarios.
5.1 Unicast Flow Example
This section details the steps in using COPS for controlling a
Unicast RSVP flow. It details the contents of the COPS messages with
respect to Figure 1.
Herzog, et al. Standards Track [Page 9]
RFC 2749 COPS usage for RSVP January 2000
PEP (router)
+-----------------+
| |
R1 ------------+if1 if2+------------ S1
| |
+-----------------+
Figure 1: Unicast Example: a single PEP view
The PEP router has two interfaces (if1, if2). Sender S1 sends to
receiver R1.
A Path message arrives from S1:
PEP --> PDP REQ := <Handle A> <Context: in & out, Path>
<In-Interface if2> <Out-Interface if1>
<ClientSI: all objects in Path message>
PDP --> PEP DEC := <Handle A> <Context: in & out, Path>
<Decision: Command, Install>
A Resv message arrives from R1:
PEP --> PDP REQ := <Handle B>
<Context: in & allocation & out, Resv>
<In-Interface if1> <Out-Interface if2>
<ClientSI: all objects in Resv message>
PDP --> PEP DEC := <Handle B>
<Context: in, Resv>
<Decision: command, Install>
<Context: allocation, Resv>
<Decision: command, Install>
<Decision: Stateless, Priority=7>
<Context: out, Resv>
<Decision: command, Install>
<Decision: replacement, POLICY-DATA1>
PEP --> PDP RPT := <Handle B>
<Report type: commit>
Notice that the Decision was split because of the need to specify
different decision objects for different context flags.
Herzog, et al. Standards Track [Page 10]
RFC 2749 COPS usage for RSVP January 2000
Time Passes, the PDP changes its decision:
PDP --> PEP DEC := <Handle B>
<Context: allocation, Resv>
<Decision: command, Install>
<Decision: Stateless, Priority=3>
Because the priority is too low, the PEP preempts the flow:
PEP --> PDP DRQ := <Handle B>
<Reason Code: Preempted>
Time Passes, the sender S1 ceases to send Path messages:
PEP --> PDP DRQ := <Handle A>
<Reason: Timeout>
5.2 Shared Multicast Flows
This section details the steps in using COPS for controlling a
multicast RSVP flow. It details the contents of the COPS messages
with respect to Figure 2.
PEP (router)
+-----------------+
| |
R1-------------+ if1 if3 +--------- S1
| |
R2----+ | |
| | |
+--------+ if2 if4 +--------- S2
| | |
R3----+ +-----------------+
Figure 2: Multicast example: a single PEP view
Figure 2 shows an RSVP PEP (router) which has two senders (S1, S2)
and three receivers (R1, R2, R3) for the same multicast session.
Interface if2 is connected to a shared media. In this example, we
assume that the multicast membership is already in place. No previous
RSVP messages were received, and the first to arrive is a Path
message on interface if3 from sender S1:
PEP --> PDP REQ := <Handle A> <Context: in, Path>
<In-interface if3>
<ClientSI: all objects in incoming Path>
Herzog, et al. Standards Track [Page 11]
RFC 2749 COPS usage for RSVP January 2000
PDP --> PEP DEC := <Handle A> <Context: in, Path>
<Decision: command, Install>
The PEP consults its forwarding table, and finds two outgoing
interface for the path (if1, if2). The exchange below is for
interface if1, another exchange would likewise be completed for if2
using the new handle B2.
PEP --> PDP REQ := <Handle B1> <Context: out, Path>
<Out-interface if1>
<clientSI: all objects in outgoing Path>
PDP --> PEP DEC := <Handle B1>
<Context: out, Path>
<Decision: command, Install>
<Decision: Replacement, POLICY-DATA1>
Here, the PDP decided to allow the forwarding of the Path message and
provided the appropriate policy-data object for interface if1.
Next, a WF Resv message from receiver R2 arrives on interface if2.
PEP --> PDP REQ := <Handle C> <Context: in & allocation, Resv>
<In-interface if2>
<ClientSI: all objects in Resv message
including RSpec1 >
PDP --> PEP DEC := <Handle C>
<Context: in, Resv>
<Decision: command, Install>
<Context: allocation, Resv>
<Decision: command, Install>
<Decision: Stateless, priority=5>
PEP --> PDP RPT := <handle C> <Commit>
Here, the PDP approves the reservation and assigned it preemption
priority of 5. The PEP responded with a commit report.
The PEP needs to forward the Resv message upstream toward S1:
PEP --> PDP REQ := <Handle E> <Context: out, Resv>
<out-interface if3>
<Client info: all objects in outgoing Resv>
Herzog, et al. Standards Track [Page 12]
RFC 2749 COPS usage for RSVP January 2000
PDP --> PEP DEC := <Handle E>
<Context: out, Resv>
<Decision: command, Install>
<Decision: replacement, POLICY-DATA2>
Note: The Context object is part of this DEC message even though it
may look redundant since the REQ specified only one context flag.
Next, a new WF Resv message from receiver R3 arrives on interface if2
with a higher RSpec (Rspec2). Given two reservations arrived on if2,
it cannot perform a request with multiple context flags, and must
issue them separately.
The PEP re-issues an updated handle C REQ with a new context object
<Context: in , Resv>, and receives a DEC for handle C.
PEP --> PDP REQ := <Handle F> <Context: in , Resv>
<In-interface if2>
<ClientSI: all objects in Resv message
including RSpec2 >
PDP --> PEP DEC := <Handle F> <Context: in , Resv>
<Decision: command, Install>
PEP --> PDP REQ := <Handle G> <Context: allocation, Resv>
<In-interface if2>
<ClientSI: all objects in merged Resv
including RSpec2 >
PDP --> PEP DEC := <Handle G>
<Context: allocation, Resv>
<Decision: command, Install>
<Decision: Stateless, Priority=5>
PEP --> PDP RPT := <handle G> <Commit>
Given the change in incoming reservations, the PEP needs to forward a
new outgoing Resv message upstream toward S1. This repeats exactly
the previous interaction of Handle E, except that the ClientSI
objects now reflect the merging of two reservations.
If an ResvErr arrives from S1, the PEP maps it to R3 only (because it
has a higher flowspec: Rspec2) the following takes place:
PEP --> PDP REQ := <Handle H> <Context: in, ResvErr>
<In-interface if3>
<ClientSI: all objects in incoming ResvErr>
Herzog, et al. Standards Track [Page 13]
RFC 2749 COPS usage for RSVP January 2000
PDP --> PEP DEC := <Handle H> <Context: in, ResvErr>
<Decision: command, Install>
PEP --> PDP REQ := <Handle I> <Context: out, ResvErr>
<Out-interface if2>
<ClientSI: all objects in outgoing ResvErr>
PDP --> PEP DEC := <Handle I>
<Context: out, ResvErr>
<Decision: command, Install>
<Decision: Replacement, POLICY-DATA3>
When S2 joins the session by sending a Path message, incoming and
outgoing Path requests are issued for the new Path. A new outgoing
Resv request would be sent to S2.
6 References
[RSVP-EXT] Herzog, S., "RSVP Extensions for Policy Control", RFC
2750, January 2000.
[RAP] Yavatkar, R., Pendarakis, D. and R. Guerin, "A Framework
for Policy Based Admission Control", RFC 2753, January
2000.
[COPS] Boyle, J., Cohen, R., Durham, D., Herzog, S., Raja, R. and
A. Sastry, "The COPS (Common Open Policy Service)
Protocol", RFC 2748, January 2000.
[RSVP] Braden, R., Zhang, L., Berson, S., Herzog, S. and S.
Jamin, "Resource ReSerVation Protocol (RSVP) - Functional
Specification", RFC 2205, September 1997.
Herzog, et al. Standards Track [Page 14]
RFC 2749 COPS usage for RSVP January 2000
7 Author Information and Acknowledgments
Special thanks to Andrew Smith and Timothy O'Malley our WG Chairs,
Fred Baker, Laura Cunningham, Russell Fenger, Roch Guerin, Ping Pan,
and Raj Yavatkar, for their valuable contributions.
Jim Boyle
Level 3 Communications
1025 Eldorado Boulevard
Broomfield, CO 80021
Phone: 720.888.1192
EMail: jboyle@Level3.net
Ron Cohen
CISCO Systems
4 Maskit St.
Herzeliya Pituach 46766 Israel
Phone: 972.9.9700064
EMail: ronc@cisco.com
David Durham
Intel
2111 NE 25th Avenue
Hillsboro, OR 97124
Phone: 503.264.6232
EMail: David.Durham@intel.com
Raju Rajan
AT&T Labs Research
180 Park Ave., P.O. Box 971
Florham Park, NJ 07932
Phone: 973.360.7229
EMail: raju@research.att.com
Herzog, et al. Standards Track [Page 15]
RFC 2749 COPS usage for RSVP January 2000
Shai Herzog
IPHighway, Inc.
55 New York Avenue
Framingham, MA 01701
Phone: 508.620.1141
EMail: herzog@iphighway.com
Arun Sastry
Cisco Systems
4 The Square
Stockley Park
Uxbridge, Middlesex UB11 1BN
UK
Phone: +44-208-756-8693
EMail: asastry@cisco.com
Herzog, et al. Standards Track [Page 16]
RFC 2749 COPS usage for RSVP January 2000
8 Full Copyright Statement
Copyright (C) The Internet Society (2000). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Herzog, et al. Standards Track [Page 17]