Network Working Group R. Austein
Request for Comments: 3364 Bourgeois Dilettant
Updates: 2673, 2874 August 2002
Category: Informational
Tradeoffs in Domain Name System (DNS) Support
for Internet Protocol version 6 (IPv6)
Status of this Memo
This memo provides information for the Internet community. It does
not specify an Internet standard of any kind. Distribution of this
memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2002). All Rights Reserved.
Abstract
The IETF has two different proposals on the table for how to do DNS
support for IPv6, and has thus far failed to reach a clear consensus
on which approach is better. This note attempts to examine the pros
and cons of each approach, in the hope of clarifying the debate so
that we can reach closure and move on.
Introduction
RFC 1886 [RFC1886] specified straightforward mechanisms to support
IPv6 addresses in the DNS. These mechanisms closely resemble the
mechanisms used to support IPv4, with a minor improvement to the
reverse mapping mechanism based on experience with CIDR. RFC 1886 is
currently listed as a Proposed Standard.
RFC 2874 [RFC2874] specified enhanced mechanisms to support IPv6
addresses in the DNS. These mechanisms provide new features that
make it possible for an IPv6 address stored in the DNS to be broken
up into multiple DNS resource records in ways that can reflect the
network topology underlying the address, thus making it possible for
the data stored in the DNS to reflect certain kinds of network
topology changes or routing architectures that are either impossible
or more difficult to represent without these mechanisms. RFC 2874 is
also currently listed as a Proposed Standard.
Austein Informational [Page 1]
RFC 3364 Tradeoffs in DNS Support for IPv6 August 2002
Both of these Proposed Standards were the output of the IPNG Working
Group. Both have been implemented, although implementation of
[RFC1886] is more widespread, both because it was specified earlier
and because it's simpler to implement.
There's little question that the mechanisms proposed in [RFC2874] are
more general than the mechanisms proposed in [RFC1886], and that
these enhanced mechanisms might be valuable if IPv6's evolution goes
in certain directions. The questions are whether we really need the
more general mechanism, what new usage problems might come along with
the enhanced mechanisms, and what effect all this will have on IPv6
deployment.
The one thing on which there does seem to be widespread agreement is
that we should make up our minds about all this Real Soon Now.
Main Advantages of Going with A6
While the A6 RR proposed in [RFC2874] is very general and provides a
superset of the functionality provided by the AAAA RR in [RFC1886],
many of the features of A6 can also be implemented with AAAA RRs via
preprocessing during zone file generation.
There is one specific area where A6 RRs provide something that cannot
be provided using AAAA RRs: A6 RRs can represent addresses in which a
prefix portion of the address can change without any action (or
perhaps even knowledge) by the parties controlling the DNS zone
containing the terminal portion (least significant bits) of the
address. This includes both so-called "rapid renumbering" scenarios
(where an entire network's prefix may change very quickly) and
routing architectures such as the former "GSE" proposal [GSE] (where
the "routing goop" portion of an address may be subject to change
without warning). A6 RRs do not completely remove the need to update
leaf zones during all renumbering events (for example, changing ISPs
would usually require a change to the upward delegation pointer), but
careful use of A6 RRs could keep the number of RRs that need to
change during such an event to a minimum.
Note that constructing AAAA RRs via preprocessing during zone file
generation requires exactly the sort of information that A6 RRs store
in the DNS. This begs the question of where the hypothetical
preprocessor obtains that information if it's not getting it from the
DNS.
Note also that the A6 RR, when restricted to its zero-length-prefix
form ("A6 0"), is semantically equivalent to an AAAA RR (with one
"wasted" octet in the wire representation), so anything that can be
done with an AAAA RR can also be done with an A6 RR.
Austein Informational [Page 2]
RFC 3364 Tradeoffs in DNS Support for IPv6 August 2002
Main Advantages of Going with AAAA
The AAAA RR proposed in [RFC1886], while providing only a subset of
the functionality provided by the A6 RR proposed in [RFC2874], has
two main points to recommend it:
- AAAA RRs are essentially identical (other than their length) to
IPv4's A RRs, so we have more than 15 years of experience to help
us predict the usage patterns, failure scenarios and so forth
associated with AAAA RRs.
- The AAAA RR is "optimized for read", in the sense that, by storing
a complete address rather than making the resolver fetch the
address in pieces, it minimizes the effort involved in fetching
addresses from the DNS (at the expense of increasing the effort
involved in injecting new data into the DNS).
Less Compelling Arguments in Favor of A6
Since the A6 RR allows a zone administrator to write zone files whose
description of addresses maps to the underlying network topology, A6
RRs can be construed as a "better" way of representing addresses than
AAAA. This may well be a useful capability, but in and of itself
it's more of an argument for better tools for zone administrators to
use when constructing zone files than a justification for changing
the resolution protocol used on the wire.
Less Compelling Arguments in Favor of AAAA
Some of the pressure to go with AAAA instead of A6 appears to be
based on the wider deployment of AAAA. Since it is possible to
construct transition tools (see discussion of AAAA synthesis, later
in this note), this does not appear to be a compelling argument if A6
provides features that we really need.
Another argument in favor of AAAA RRs over A6 RRs appears to be that
the A6 RR's advanced capabilities increase the number of ways in
which a zone administrator could build a non-working configuration.
While operational issues are certainly important, this is more of
argument that we need better tools for zone administrators than it is
a justification for turning away from A6 if A6 provides features that
we really need.
Austein Informational [Page 3]
RFC 3364 Tradeoffs in DNS Support for IPv6 August 2002
Potential Problems with A6
The enhanced capabilities of the A6 RR, while interesting, are not in
themselves justification for choosing A6 if we don't really need
those capabilities. The A6 RR is "optimized for write", in the sense
that, by making it possible to store fragmented IPv6 addresses in the
DNS, it makes it possible to reduce the effort that it takes to
inject new data into the DNS (at the expense of increasing the effort
involved in fetching data from the DNS). This may be justified if we
expect the effort involved in maintaining AAAA-style DNS entries to
be prohibitive, but in general, we expect the DNS data to be read
more frequently than it is written, so we need to evaluate this
particular tradeoff very carefully.
There are also several potential issues with A6 RRs that stem
directly from the feature that makes them different from AAAA RRs:
the ability to build up address via chaining.
Resolving a chain of A6 RRs involves resolving a series of what are
almost independent queries, but not quite. Each of these sub-queries
takes some non-zero amount of time, unless the answer happens to be
in the resolver's local cache already. Assuming that resolving an
AAAA RR takes time T as a baseline, we can guess that, on the
average, it will take something approaching time N*T to resolve an
N-link chain of A6 RRs, although we would expect to see a fairly good
caching factor for the A6 fragments representing the more significant
bits of an address. This leaves us with two choices, neither of
which is very good: we can decrease the amount of time that the
resolver is willing to wait for each fragment, or we can increase the
amount of time that a resolver is willing to wait before returning
failure to a client. What little data we have on this subject
suggests that users are already impatient with the length of time it
takes to resolve A RRs in the IPv4 Internet, which suggests that they
are not likely to be patient with significantly longer delays in the
IPv6 Internet. At the same time, terminating queries prematurely is
both a waste of resources and another source of user frustration.
Thus, we are forced to conclude that indiscriminate use of long A6
chains is likely to lead to problems.
To make matters worse, the places where A6 RRs are likely to be most
critical for rapid renumbering or GSE-like routing are situations
where the prefix name field in the A6 RR points to a target that is
not only outside the DNS zone containing the A6 RR, but is
administered by a different organization (for example, in the case of
an end user's site, the prefix name will most likely point to a name
belonging to an ISP that provides connectivity for the site). While
pointers out of zone are not a problem per se, pointers to other
organizations are somewhat more difficult to maintain and less
Austein Informational [Page 4]
RFC 3364 Tradeoffs in DNS Support for IPv6 August 2002
susceptible to automation than pointers within a single organization
would be. Experience both with glue RRs and with PTR RRs in the IN-
ADDR.ARPA tree suggests that many zone administrators do not really
understand how to set up and maintain these pointers properly, and we
have no particular reason to believe that these zone administrators
will do a better job with A6 chains than they do today. To be fair,
however, the alternative case of building AAAA RRs via preprocessing
before loading zones has many of the same problems; at best, one can
claim that using AAAA RRs for this purpose would allow DNS clients to
get the wrong answer somewhat more efficiently than with A6 RRs.
Finally, assuming near total ignorance of how likely a query is to
fail, the probability of failure with an N-link A6 chain would appear
to be roughly proportional to N, since each of the queries involved
in resolving an A6 chain would have the same probability of failure
as a single AAAA query. Note again that this comment applies to
failures in the the process of resolving a query, not to the data
obtained via that process. Arguably, in an ideal world, A6 RRs would
increase the probability of the answer a client (finally) gets being
right, assuming that nothing goes wrong in the query process, but we
have no real idea how to quantify that assumption at this point even
to the hand-wavey extent used elsewhere in this note.
One potential problem that has been raised in the past regarding A6
RRs turns out not to be a serious issue. The A6 design includes the
possibility of there being more than one A6 RR matching the prefix
name portion of a leaf A6 RR. That is, an A6 chain may not be a
simple linked list, it may in fact be a tree, where each branch
represents a possible prefix. Some critics of A6 have been concerned
that this will lead to a wild expansion of queries, but this turns
out not to be a problem if a resolver simply follows the "bounded
work per query" rule described in RFC 1034 (page 35). That rule
applies to all work resulting from attempts to process a query,
regardless of whether it's a simple query, a CNAME chain, an A6 tree,
or an infinite loop. The client may not get back a useful answer in
cases where the zone has been configured badly, but a proper
implementation should not produce a query explosion as a result of
processing even the most perverse A6 tree, chain, or loop.
Interactions with DNSSEC
One of the areas where AAAA and A6 RRs differ is in the precise
details of how they interact with DNSSEC. The following comments
apply only to non-zero-prefix A6 RRs (A6 0 RRs, once again, are
semantically equivalent to AAAA RRs).
Austein Informational [Page 5]
RFC 3364 Tradeoffs in DNS Support for IPv6 August 2002
Other things being equal, the time it takes to re-sign all of the
addresses in a zone after a renumbering event is longer with AAAA RRs
than with A6 RRs (because each address record has to be re-signed
rather than just signing a common prefix A6 RR and a few A6 0 RRs
associated with the zone's name servers). Note, however, that in
general this does not present a serious scaling problem, because the
re-signing is performed in the leaf zones.
Other things being equal, there's more work involved in verifying the
signatures received back for A6 RRs, because each address fragment
has a separate associated signature. Similarly, a DNS message
containing a set of A6 address fragments and their associated
signatures will be larger than the equivalent packet with a single
AAAA (or A6 0) and a single associated signature.
Since AAAA RRs cannot really represent rapid renumbering or GSE-style
routing scenarios very well, it should not be surprising that DNSSEC
signatures of AAAA RRs are also somewhat problematic. In cases where
the AAAA RRs would have to be changing very quickly to keep up with
prefix changes, the time required to re-sign the AAAA RRs may be
prohibitive.
Empirical testing by Bill Sommerfeld [Sommerfeld] suggests that
333MHz Celeron laptop with 128KB L2 cache and 64MB RAM running the
BIND-9 dnssec-signzone program under NetBSD can generate roughly 40
1024-bit RSA signatures per second. Extrapolating from this,
assuming one A RR, one AAAA RR, and one NXT RR per host, this
suggests that it would take this laptop a few hours to sign a zone
listing 10**5 hosts, or about a day to sign a zone listing 10**6
hosts using AAAA RRs.
This suggests that the additional effort of re-signing a large zone
full of AAAA RRs during a re-numbering event, while noticeable, is
only likely to be prohibitive in the rapid renumbering case where
AAAA RRs don't work well anyway.
Interactions with Dynamic Update
DNS dynamic update appears to work equally well for AAAA or A6 RRs,
with one minor exception: with A6 RRs, the dynamic update client
needs to know the prefix length and prefix name. At present, no
mechanism exists to inform a dynamic update client of these values,
but presumably such a mechanism could be provided via an extension to
DHCP, or some other equivalent could be devised.
Austein Informational [Page 6]
RFC 3364 Tradeoffs in DNS Support for IPv6 August 2002
Transition from AAAA to A6 Via AAAA Synthesis
While AAAA is at present more widely deployed than A6, it is possible
to transition from AAAA-aware DNS software to A6-aware DNS software.
A rough plan for this was presented at IETF-50 in Minneapolis and has
been discussed on the ipng mailing list. So if the IETF concludes
that A6's enhanced capabilities are necessary, it should be possible
to transition from AAAA to A6.
The details of this transition have been left to a separate document,
but the general idea is that the resolver that is performing
iterative resolution on behalf of a DNS client program could
synthesize AAAA RRs representing the result of performing the
equivalent A6 queries. Note that in this case it is not possible to
generate an equivalent DNSSEC signature for the AAAA RR, so clients
that care about performing DNSSEC validation for themselves would
have to issue A6 queries directly rather than relying on AAAA
synthesis.
Bitlabels
While the differences between AAAA and A6 RRs have generated most of
the discussion to date, there are also two proposed mechanisms for
building the reverse mapping tree (the IPv6 equivalent of IPv4's IN-
ADDR.ARPA tree).
[RFC1886] proposes a mechanism very similar to the IN-ADDR.ARPA
mechanism used for IPv4 addresses: the RR name is the hexadecimal
representation of the IPv6 address, reversed and concatenated with a
well-known suffix, broken up with a dot between each hexadecimal
digit. The resulting DNS names are somewhat tedious for humans to
type, but are very easy for programs to generate. Making each
hexadecimal digit a separate label means that delegation on arbitrary
bit boundaries will result in a maximum of 16 NS RRsets per label
level; again, the mechanism is somewhat tedious for humans, but is
very easy to program. As with IPv4's IN-ADDR.ARPA tree, the one
place where this scheme is weak is in handling delegations in the
least significant label; however, since there appears to be no real
need to delegate the least significant four bits of an IPv6 address,
this does not appear to be a serious restriction.
[RFC2874] proposed a radically different way of naming entries in the
reverse mapping tree: rather than using textual representations of
addresses, it proposes to use a new kind of DNS label (a "bit label")
to represent binary addresses directly in the DNS. This has the
advantage of being significantly more compact than the textual
representation, and arguably might have been a better solution for
DNS to use for this purpose if it had been designed into the protocol
Austein Informational [Page 7]
RFC 3364 Tradeoffs in DNS Support for IPv6 August 2002
from the outset. Unfortunately, experience to date suggests that
deploying a new DNS label type is very hard: all of the DNS name
servers that are authoritative for any portion of the name in
question must be upgraded before the new label type can be used, as
must any resolvers involved in the resolution process. Any name
server that has not been upgraded to understand the new label type
will reject the query as being malformed.
Since the main benefit of the bit label approach appears to be an
ability that we don't really need (delegation in the least
significant four bits of an IPv6 address), and since the upgrade
problem is likely to render bit labels unusable until a significant
portion of the DNS code base has been upgraded, it is difficult to
escape the conclusion that the textual solution is good enough.
DNAME RRs
[RFC2874] also proposes using DNAME RRs as a way of providing the
equivalent of A6's fragmented addresses in the reverse mapping tree.
That is, by using DNAME RRs, one can write zone files for the reverse
mapping tree that have the same ability to cope with rapid
renumbering or GSE-style routing that the A6 RR offers in the main
portion of the DNS tree. Consequently, the need to use DNAME in the
reverse mapping tree appears to be closely tied to the need to use
fragmented A6 in the main tree: if one is necessary, so is the other,
and if one isn't necessary, the other isn't either.
Other uses have also been proposed for the DNAME RR, but since they
are outside the scope of the IPv6 address discussion, they will not
be addressed here.
Recommendation
Distilling the above feature comparisons down to their key elements,
the important questions appear to be:
(a) Is IPv6 going to do rapid renumbering or GSE-like routing?
(b) Is the reverse mapping tree for IPv6 going to require delegation
in the least significant four bits of the address?
Question (a) appears to be the key to the debate. This is really a
decision for the IPv6 community to make, not the DNS community.
Question (b) is also for the IPv6 community to make, but it seems
fairly obvious that the answer is "no".
Austein Informational [Page 8]
RFC 3364 Tradeoffs in DNS Support for IPv6 August 2002
Recommendations based on these questions:
(1) If the IPv6 working groups seriously intend to specify and deploy
rapid renumbering or GSE-like routing, we should transition to
using the A6 RR in the main tree and to using DNAME RRs as
necessary in the reverse tree.
(2) Otherwise, we should keep the simpler AAAA solution in the main
tree and should not use DNAME RRs in the reverse tree.
(3) In either case, the reverse tree should use the textual
representation described in [RFC1886] rather than the bit label
representation described in [RFC2874].
(4) If we do go to using A6 RRs in the main tree and to using DNAME
RRs in the reverse tree, we should write applicability statements
and implementation guidelines designed to discourage excessively
complex uses of these features; in general, any network that can
be described adequately using A6 0 RRs and without using DNAME
RRs should be described that way, and the enhanced features
should be used only when absolutely necessary, at least until we
have much more experience with them and have a better
understanding of their failure modes.
Security Considerations
This note compares two mechanisms with similar security
characteristics, but there are a few security implications to the
choice between these two mechanisms:
(1) The two mechanisms have similar but not identical interactions
with DNSSEC. Please see the section entitled "Interactions with
DNSSEC" (above) for a discussion of these issues.
(2) To the extent that operational complexity is the enemy of
security, the tradeoffs in operational complexity discussed
throughout this note have an impact on security.
(3) To the extent that protocol complexity is the enemy of security,
the additional protocol complexity of [RFC2874] as compared to
[RFC1886] has some impact on security.
IANA Considerations
None, since all of these RR types have already been allocated.
Austein Informational [Page 9]
RFC 3364 Tradeoffs in DNS Support for IPv6 August 2002
Acknowledgments
This note is based on a number of discussions both public and private
over a period of (at least) eight years, but particular thanks go to
Alain Durand, Bill Sommerfeld, Christian Huitema, Jun-ichiro itojun
Hagino, Mark Andrews, Matt Crawford, Olafur Gudmundsson, Randy Bush,
and Sue Thomson, none of whom are responsible for what the author did
with their ideas.
References
[RFC1886] Thomson, S. and C. Huitema, "DNS Extensions to support
IP version 6", RFC 1886, December 1995.
[RFC2874] Crawford, M. and C. Huitema, "DNS Extensions to Support
IPv6 Address Aggregation and Renumbering", RFC 2874,
July 2000.
[Sommerfeld] Private message to the author from Bill Sommerfeld dated
21 March 2001, summarizing the result of experiments he
performed on a copy of the MIT.EDU zone.
[GSE] "GSE" was an evolution of the so-called "8+8" proposal
discussed by the IPng working group in 1996 and 1997.
The GSE proposal itself was written up as an Internet-
Draft, which has long since expired. Readers interested
in the details and history of GSE should review the IPng
working group's mailing list archives and minutes from
that period.
Author's Address
Rob Austein
EMail: sra@hactrn.net
Austein Informational [Page 10]
RFC 3364 Tradeoffs in DNS Support for IPv6 August 2002
Full Copyright Statement
Copyright (C) The Internet Society (2002). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Austein Informational [Page 11]