Network Working Group A. Siddiqui
Request for Comments: 4711 D. Romascanu
Category: Standards Track Avaya
E. Golovinsky
Alert Logic
October 2006
Real-time Application Quality-of-Service Monitoring (RAQMON) MIB
Status of This Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2006).
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
The document proposes an extension to the Remote Monitoring MIB, RFC
2819. In particular, it describes managed objects used for real-time
application Quality of Service (QoS) monitoring.
Table of Contents
1. Introduction ....................................................2
2. The Internet-Standard Management Framework ......................2
3. RAQMON Framework ................................................2
4. Structure of the RAQMON MIB .....................................2
5. RAQMON MIB Definitions ..........................................3
6. Security Considerations ........................................33
7. IANA Considerations ............................................35
8. Acknowledgements ...............................................35
9. Normative References ...........................................36
10. Informative References ........................................36
Siddiqui, et al. Standards Track [Page 1]
RFC 4711 RAQMON MIB October 2006
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it extends [RFC2819] with managed objects used for
real-time application QoS monitoring.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
2. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
3. RAQMON Framework
As outlined in [RFC4710], the RAQMON framework is based on three
entities:
- RAQMON Data Source (RDS)
- RAQMON Report Collector (RRC)
- RAQMON MIB Structure
The RAQMON MIB describes information passed between RRCs and a RAQMON
Application ("RAQMON manager").
4. Structure of the RAQMON MIB
The RAQMON MIB module is composed of three MIB groups:
raqmonSession, raqmonException, and raqmonConfig.
The raqmonSession MIB group incorporates the following tables:
Siddiqui, et al. Standards Track [Page 2]
RFC 4711 RAQMON MIB October 2006
- The raqmonParticpantTable contains information about
participants in open and closed (terminated) sessions, including
parameters of the sessions they are involved in, aggregated
since the beginning of the session.
- The raqmonQosTable contains historical information about QoS
during sessions. The set of parameters represented in this
table is more restricted, but it includes historical per-
RAQMON-report information.
- The raqmonParticpantAddrTable maps participant addresses into
the indices of the raqmonParticpantTable. This table allows
management applications to find entries sorted by
raqmonParticipantAddr rather than raqmonParticipantStartDate.
The raqmonException MIB group includes a table of filters that
trigger notifications for sessions with poor QoS.
The raqmonConfig MIB group includes objects that define the
configuration of the RAQMON Report Collector.
This MIB module MUST be implemented by RAQMON Report Collectors.
A separate MIB module is defined in [RFC4712] for mapping the RAQMON
PDUs onto an SNMP transport. The MIB module defined in [RFC4712] is
normally implemented by RAQMON Data Sources (RDS).
5. RAQMON MIB Definitions
The MIB module herein IMPORTS definitions from the following:
SNMPv2-SMI [RFC2578]
SNMPv2-TC [RFC2579]
SNMPv2-CONF [RFC2580]
RMON-MIB [RFC2819]
SNMP-FRAMEWORK-MIB [RFC3411]
INET-ADDRESS-MIB [RFC4001]
It also uses REFERENCE clauses to refer to [RFC4710].
It also mentions [RFC3737] with respect to the MODULE-IDENTITY OID
allocation.
Siddiqui, et al. Standards Track [Page 3]
RFC 4711 RAQMON MIB October 2006
RAQMON-MIB DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-GROUP, NOTIFICATION-GROUP, MODULE-COMPLIANCE
FROM SNMPv2-CONF
Integer32, Unsigned32,
Gauge32, Counter32, OBJECT-TYPE,
MODULE-IDENTITY, NOTIFICATION-TYPE
FROM SNMPv2-SMI
InetAddressType, InetAddress, InetPortNumber
FROM INET-ADDRESS-MIB
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
rmon
FROM RMON-MIB
RowStatus, TruthValue, DateAndTime, RowPointer
FROM SNMPv2-TC;
raqmonMIB MODULE-IDENTITY
LAST-UPDATED "200610100000Z" -- October 10, 2006
ORGANIZATION
"IETF RMON MIB Working Group"
CONTACT-INFO
"WG Charter:
http://www.ietf.org/html.charters/rmonmib-charter.html
Mailing lists:
General Discussion: rmonmib@ietf.org
To Subscribe: rmonmib-requests@ietf.org
In Body: subscribe your_email_address
Chair: Andy Bierman
Email: ietf@andybierman.com
Editor: Dan Romascanu
Avaya
Email: dromasca@avaya.com"
DESCRIPTION
"Real-Time Application QoS Monitoring MIB.
Copyright (c) The Internet Society (2006).
This version of this MIB module is part of
RFC 4711; See the RFC itself for full legal notices."
REVISION "200610100000Z"
DESCRIPTION
"Initial version, published as RFC 4711."
::= { rmon 31 }
-- This OID allocation conforms to [RFC3737]
Siddiqui, et al. Standards Track [Page 4]
RFC 4711 RAQMON MIB October 2006
--
-- Node definitions
--
raqmonNotifications OBJECT IDENTIFIER ::= { raqmonMIB 0 }
raqmonSessionAlarm NOTIFICATION-TYPE
OBJECTS { raqmonParticipantAddr,
raqmonParticipantName,
raqmonParticipantPeerAddrType,
raqmonParticipantPeerAddr,
raqmonQoSEnd2EndNetDelay,
raqmonQoSInterArrivalJitter,
raqmonQosLostPackets,
raqmonQosRcvdPackets }
STATUS current
DESCRIPTION
"A notification generated by an entry in the
raqmonSessionExceptionTable."
::= { raqmonNotifications 1 }
raqmonMIBObjects OBJECT IDENTIFIER ::= { raqmonMIB 1 }
raqmonSession OBJECT IDENTIFIER ::= { raqmonMIBObjects 1 }
raqmonParticipantTable OBJECT-TYPE
SYNTAX SEQUENCE OF RaqmonParticipantEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about participants in
both active and closed (terminated) sessions."
::= { raqmonSession 1 }
raqmonParticipantEntry OBJECT-TYPE
SYNTAX RaqmonParticipantEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row contains information for a single session
(application) run by one participant.
Indexation by the start time of the session aims
to ease sorting by management applications. Agents MUST
NOT report identical start times for any two sessions
on the same host.
Rows are removed for inactive sessions
when implementation-specific age or space limits are
reached."
Siddiqui, et al. Standards Track [Page 5]
RFC 4711 RAQMON MIB October 2006
INDEX { raqmonParticipantStartDate, raqmonParticipantIndex }
::= { raqmonParticipantTable 1 }
RaqmonParticipantEntry ::=
SEQUENCE {
raqmonParticipantStartDate DateAndTime,
raqmonParticipantIndex Unsigned32,
raqmonParticipantReportCaps BITS,
raqmonParticipantAddrType InetAddressType,
raqmonParticipantAddr InetAddress,
raqmonParticipantSendPort InetPortNumber,
raqmonParticipantRecvPort InetPortNumber,
raqmonParticipantSetupDelay Integer32,
raqmonParticipantName SnmpAdminString,
raqmonParticipantAppName SnmpAdminString,
raqmonParticipantQosCount Gauge32,
raqmonParticipantEndDate DateAndTime,
raqmonParticipantDestPayloadType Integer32,
raqmonParticipantSrcPayloadType Integer32,
raqmonParticipantActive TruthValue,
raqmonParticipantPeer RowPointer,
raqmonParticipantPeerAddrType InetAddressType,
raqmonParticipantPeerAddr InetAddress,
raqmonParticipantSrcL2Priority Integer32,
raqmonParticipantDestL2Priority Integer32,
raqmonParticipantSrcDSCP Integer32,
raqmonParticipantDestDSCP Integer32,
raqmonParticipantCpuMean Integer32,
raqmonParticipantCpuMin Integer32,
raqmonParticipantCpuMax Integer32,
raqmonParticipantMemoryMean Integer32,
raqmonParticipantMemoryMin Integer32,
raqmonParticipantMemoryMax Integer32,
raqmonParticipantNetRTTMean Integer32,
raqmonParticipantNetRTTMin Integer32,
raqmonParticipantNetRTTMax Integer32,
raqmonParticipantIAJitterMean Integer32,
raqmonParticipantIAJitterMin Integer32,
raqmonParticipantIAJitterMax Integer32,
raqmonParticipantIPDVMean Integer32,
raqmonParticipantIPDVMin Integer32,
raqmonParticipantIPDVMax Integer32,
raqmonParticipantNetOwdMean Integer32,
raqmonParticipantNetOwdMin Integer32,
raqmonParticipantNetOwdMax Integer32,
raqmonParticipantAppDelayMean Integer32,
raqmonParticipantAppDelayMin Integer32,
raqmonParticipantAppDelayMax Integer32,
Siddiqui, et al. Standards Track [Page 6]
RFC 4711 RAQMON MIB October 2006
raqmonParticipantPacketsRcvd Integer32,
raqmonParticipantPacketsSent Integer32,
raqmonParticipantOctetsRcvd Integer32,
raqmonParticipantOctetsSent Integer32,
raqmonParticipantLostPackets Integer32,
raqmonParticipantLostPacketsFrct Integer32,
raqmonParticipantDiscards Integer32,
raqmonParticipantDiscardsFrct Integer32
}
raqmonParticipantStartDate OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The date and time of this entry.
It will be the date and time
of the first report received."
::= { raqmonParticipantEntry 1 }
raqmonParticipantIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index of the conceptual row, which is for SNMP
purposes only and has no relation to any protocol value.
There is no requirement that these rows be created or
maintained sequentially. The index will be unique for a
particular date and time."
::= { raqmonParticipantEntry 2 }
raqmonParticipantReportCaps OBJECT-TYPE
SYNTAX BITS {
raqmonPartRepDsrcName(0),
raqmonPartRepRecvName(1),
raqmonPartRepDsrcPort(2),
raqmonPartRepRecvPort(3),
raqmonPartRepSetupTime(4),
raqmonPartRepSetupDelay(5),
raqmonPartRepSessionDuration(6),
raqmonPartRepSetupStatus(7),
raqmonPartRepRTEnd2EndNetDelay(8),
raqmonPartRepOWEnd2EndNetDelay(9),
raqmonPartApplicationDelay(10),
raqmonPartRepIAJitter(11),
raqmonPartRepIPDV(12),
Siddiqui, et al. Standards Track [Page 7]
RFC 4711 RAQMON MIB October 2006
raqmonPartRepRcvdPackets(13),
raqmonPartRepRcvdOctets(14),
raqmonPartRepSentPackets(15),
raqmonPartRepSentOctets(16),
raqmonPartRepCumPacketsLoss(17),
raqmonPartRepFractionPacketsLoss(18),
raqmonPartRepCumDiscards(19),
raqmonPartRepFractionDiscards(20),
raqmonPartRepSrcPayloadType(21),
raqmonPartRepDestPayloadType(22),
raqmonPartRepSrcLayer2Priority(23),
raqmonPartRepSrcTosDscp(24),
raqmonPartRepDestLayer2Priority(25),
raqmonPartRepDestTosDscp(26),
raqmonPartRepCPU(27),
raqmonPartRepMemory(28),
raqmonPartRepAppName(29)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Report capabilities of the participant, as perceived
by the Collector.
If the participant can report the Data Source Name as
defined in [RFC4710], Section 5.3, then the
raqmonPartRepDsrcName bit will be set.
If the participant can report the Receiver Name as
defined in [RFC4710], Section 5.4, then the
raqmonPartRepRecvName bit will be set.
If the participant can report the Data Source Port as
defined in [RFC4710], Section 5.5, then the
raqmonPartRepDsrcPort bit will be set.
If the participant can report the Receiver Port as
defined in [RFC4710], Section 5.6, then the
raqmonPartRepRecvPort bit will be set.
If the participant can report the Session Setup Time as
defined in [RFC4710], Section 5.7, then the
raqmonPartRepSetupTime bit will be set.
If the participant can report the Session Setup Delay as
defined in [RFC4710], Section 5.8, then the
raqmonPartRepSetupDelay bit will be set.
Siddiqui, et al. Standards Track [Page 8]
RFC 4711 RAQMON MIB October 2006
If the participant can report the Session Duration as
defined in [RFC4710], Section 5.9, then the
raqmonPartRepSessionDuration bit will be set.
If the participant can report the Setup Status as
defined in [RFC4710], Section 5.10, then the
raqmonPartRepSetupStatus bit will be set.
If the participant can report the Round-Trip End-to-end
Network Delay as defined in [RFC4710], Section 5.11,
then the raqmonPartRepRTEnd2EndNetDelay bit will be set.
If the participant can report the One-way End-to-end
Network Delay as defined in [RFC4710], Section 5.12,
then the raqmonPartRepOWEnd2EndNetDelay bit will be set.
If the participant can report the Application Delay as
defined in [RFC4710], Section 5.13, then the
raqmonPartApplicationDelay bit will be set.
If the participant can report the Inter-Arrival Jitter
as defined in [RFC4710], Section 5.14, then the
raqmonPartRepIAJitter bit will be set.
If the participant can report the IP Packet Delay
Variation as defined in [RFC4710], Section 5.15, then
the raqmonPartRepIPDV bit will be set.
If the participant can report the number of application
packets received as defined in [RFC4710], Section 5.16,
then the raqmonPartRepRcvdPackets bit will be set.
If the participant can report the number of application
octets received as defined in [RFC4710], Section 5.17,
then the raqmonPartRepRcvdOctets bit will be set.
If the participant can report the number of application
packets sent as defined in [RFC4710], Section 5.18, then
the raqmonPartRepSentPackets bit will be set.
If the participant can report the number of application
octets sent as defined in [RFC4710], Section 5.19, then
the raqmonPartRepSentOctets bit will be set.
If the participant can report the number of cumulative
packets lost as defined in [RFC4710], Section 5.20, then
the raqmonPartRepCumPacketsLoss bit will be set.
Siddiqui, et al. Standards Track [Page 9]
RFC 4711 RAQMON MIB October 2006
If the participant can report the fraction of packet
loss as defined in [RFC4710], Section 5.21, then the
raqmonPartRepFractionPacketsLoss bit will be set.
If the participant can report the number of cumulative
discards as defined in [RFC4710], Section 5.22, then the
raqmonPartRepCumDiscards bit will be set.
If the participant can report the fraction of discards
as defined in [RFC4710], Section 5.23, then the
raqmonPartRepFractionDiscards bit will be set.
If the participant can report the Source Payload Type as
defined in [RFC4710], Section 5.24, then the
raqmonPartRepSrcPayloadType bit will be set.
If the participant can report the Destination Payload
Type as defined in [RFC4710], Section 5.25, then the
raqmonPartRepDestPayloadType bit will be set.
If the participant can report the Source Layer 2
Priority as defined in [RFC4710], Section 5.26, then the
raqmonPartRepSrcLayer2Priority bit will be set.
If the participant can report the Source DSCP/ToS value
as defined in [RFC4710], Section 5.27, then the
raqmonPartRepSrcToSDscp bit will be set.
If the participant can report the Destination Layer 2
Priority as defined in [RFC4710], Section 5.28, then the
raqmonPartRepDestLayer2Priority bit will be set.
If the participant can report the Destination DSCP/ToS
Value as defined in [RFC4710], Section 5.29, then the
raqmonPartRepDestToSDscp bit will be set.
If the participant can report the CPU utilization as
defined in [RFC4710], Section 5.30, then the
raqmonPartRepCPU bit will be set.
If the participant can report the memory utilization as
defined in [RFC4710], Section 5.31, then the
raqmonPartRepMemory bit will be set.
If the participant can report the Application Name as
defined in [RFC4710], Section 5.32, then the
raqmonPartRepAppName bit will be set.
Siddiqui, et al. Standards Track [Page 10]
RFC 4711 RAQMON MIB October 2006
The capability of reporting of a specific metric does
not mandate that the metric must be reported permanently
by the data source to the respective collector. Some
data sources MAY be configured not to send a metric, or
some metrics may not be relevant to the specific
application."
::= { raqmonParticipantEntry 3 }
raqmonParticipantAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the Internet address of the participant for
this session."
::= { raqmonParticipantEntry 4 }
raqmonParticipantAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Internet Address of the participant for this
session. Formatting of this object is determined
by the value of raqmonParticipantAddrType."
::= { raqmonParticipantEntry 5 }
raqmonParticipantSendPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Port from which session data is sent.
If the value was not reported to the collector,
this object will have the value 0."
REFERENCE
"Section 5.5 of the [RFC4710]"
::= { raqmonParticipantEntry 6 }
raqmonParticipantRecvPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Port on which session data is received.
If the value was not reported to the collector,
this object will have the value 0."
REFERENCE
Siddiqui, et al. Standards Track [Page 11]
RFC 4711 RAQMON MIB October 2006
"Section 5.6 of the [RFC4710]"
::= { raqmonParticipantEntry 7 }
raqmonParticipantSetupDelay OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Session setup time.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.8 of the [RFC4710]"
::= { raqmonParticipantEntry 8 }
raqmonParticipantName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The data source name for the participant."
REFERENCE
"Section 5.3 of the [RFC4710]"
::= { raqmonParticipantEntry 9 }
raqmonParticipantAppName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A string giving the name and possibly the version
of the application generating the stream, e.g.,
'videotool 1.2.'
This information may be useful for debugging purposes
and is similar to the Mailer or Mail-System-Version SMTP
headers. The tool value is expected to remain constant
for the duration of the session."
REFERENCE
"Section 5.32 of the [RFC4710]"
::= { raqmonParticipantEntry 10 }
raqmonParticipantQosCount OBJECT-TYPE
SYNTAX Gauge32
UNITS "entries"
MAX-ACCESS read-only
STATUS current
Siddiqui, et al. Standards Track [Page 12]
RFC 4711 RAQMON MIB October 2006
DESCRIPTION
"The current number of entries in the raqmonQosTable
for this participant and session."
::= { raqmonParticipantEntry 11 }
raqmonParticipantEndDate OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The date and time of the most recent report received."
::= { raqmonParticipantEntry 12 }
raqmonParticipantDestPayloadType OBJECT-TYPE
SYNTAX Integer32 (-1|0..127)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Destination Payload Type.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"RFC 3551 and Section 5.25 of the [RFC4710]"
::= { raqmonParticipantEntry 13 }
raqmonParticipantSrcPayloadType OBJECT-TYPE
SYNTAX Integer32 (-1|0..127)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Source Payload Type.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"RFC 3551 and Section 5.24 of the [RFC4710]"
::= { raqmonParticipantEntry 14 }
raqmonParticipantActive OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Value 'true' indicates that the session
for this participant is active (open).
Value 'false' indicates that the session
is closed (terminated)."
::= { raqmonParticipantEntry 15 }
Siddiqui, et al. Standards Track [Page 13]
RFC 4711 RAQMON MIB October 2006
raqmonParticipantPeer OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The pointer to the corresponding entry in this table for
the other peer participant. If there is no such entry
in the participant table of the collector represented by
this SNMP agent, then the value will be { 0 0 }.
"
::= { raqmonParticipantEntry 16 }
raqmonParticipantPeerAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the Internet address of the peer participant
for this session."
::= { raqmonParticipantEntry 17 }
raqmonParticipantPeerAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Internet Address of the peer participant for this
session. Formatting of this object is determined by
the value of raqmonParticipantPeerAddrType."
::= { raqmonParticipantEntry 18 }
raqmonParticipantSrcL2Priority OBJECT-TYPE
SYNTAX Integer32 (-1|0..7)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Source Layer 2 Priority.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.26 of the [RFC4710]"
::= { raqmonParticipantEntry 19 }
raqmonParticipantDestL2Priority OBJECT-TYPE
SYNTAX Integer32 (-1|0..7)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Siddiqui, et al. Standards Track [Page 14]
RFC 4711 RAQMON MIB October 2006
"Destination Layer 2 Priority.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.28 of the [RFC4710]"
::= { raqmonParticipantEntry 20 }
raqmonParticipantSrcDSCP OBJECT-TYPE
SYNTAX Integer32 (-1|0..63)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Source Layer 3 DSCP value.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.27 of the [RFC4710]"
::= { raqmonParticipantEntry 21 }
raqmonParticipantDestDSCP OBJECT-TYPE
SYNTAX Integer32 (-1|0..63)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Destination Layer 3 DSCP value."
REFERENCE
"Section 5.29 of the [RFC4710]"
::= { raqmonParticipantEntry 22 }
raqmonParticipantCpuMean OBJECT-TYPE
SYNTAX Integer32 (-1|0..100)
UNITS "percents"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Mean CPU utilization.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.30 of the [RFC4710]"
::= { raqmonParticipantEntry 23 }
raqmonParticipantCpuMin OBJECT-TYPE
SYNTAX Integer32 (-1|0..100)
UNITS "percents"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Siddiqui, et al. Standards Track [Page 15]
RFC 4711 RAQMON MIB October 2006
"Minimum CPU utilization.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.30 of the [RFC4710]"
::= { raqmonParticipantEntry 24 }
raqmonParticipantCpuMax OBJECT-TYPE
SYNTAX Integer32 (-1|0..100)
UNITS "percents"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum CPU utilization.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.30 of the [RFC4710]"
::= { raqmonParticipantEntry 25 }
raqmonParticipantMemoryMean OBJECT-TYPE
SYNTAX Integer32 (-1|0..100)
UNITS "percents"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Mean memory utilization.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.31 of the [RFC4710]"
::= { raqmonParticipantEntry 26 }
raqmonParticipantMemoryMin OBJECT-TYPE
SYNTAX Integer32 (-1|0..100)
UNITS "percents"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Minimum memory utilization.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.31 of the [RFC4710]"
::= { raqmonParticipantEntry 27 }
raqmonParticipantMemoryMax OBJECT-TYPE
SYNTAX Integer32 (-1|0..100)
Siddiqui, et al. Standards Track [Page 16]
RFC 4711 RAQMON MIB October 2006
UNITS "percents"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum memory utilization.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.31 of the [RFC4710]"
::= { raqmonParticipantEntry 28 }
raqmonParticipantNetRTTMean OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Mean round-trip end-to-end network
delay over the entire session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.11 of the [RFC4710]"
::= { raqmonParticipantEntry 29 }
raqmonParticipantNetRTTMin OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Minimum round-trip end-to-end network delay
over the entire session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.11 of the [RFC4710]"
::= { raqmonParticipantEntry 30 }
raqmonParticipantNetRTTMax OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum round-trip end-to-end network delay
over the entire session.
If the value was not reported to the collector,
Siddiqui, et al. Standards Track [Page 17]
RFC 4711 RAQMON MIB October 2006
this object will have the value -1."
REFERENCE
"Section 5.11 of the [RFC4710]"
::= { raqmonParticipantEntry 31 }
raqmonParticipantIAJitterMean OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Mean inter-arrival jitter over the entire session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.14 of the [RFC4710]"
::= { raqmonParticipantEntry 32 }
raqmonParticipantIAJitterMin OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Minimum inter-arrival jitter over the entire session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.14 of the [RFC4710]"
::= { raqmonParticipantEntry 33 }
raqmonParticipantIAJitterMax OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum inter-arrival jitter over the entire session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.14 of the [RFC4710]"
::= { raqmonParticipantEntry 34 }
raqmonParticipantIPDVMean OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
Siddiqui, et al. Standards Track [Page 18]
RFC 4711 RAQMON MIB October 2006
STATUS current
DESCRIPTION
"Mean IP packet delay variation over the entire session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.15 of the [RFC4710]"
::= { raqmonParticipantEntry 35 }
raqmonParticipantIPDVMin OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Minimum IP packet delay variation over the entire
session. If the value was not reported to the
collector, this object will have the value -1."
REFERENCE
"Section 5.15 of the [RFC4710]"
::= { raqmonParticipantEntry 36 }
raqmonParticipantIPDVMax OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum IP packet delay variation over the entire
session. If the value was not reported to the
collector, this object will have the value -1."
REFERENCE
"Section 5.15 of the [RFC4710]"
::= { raqmonParticipantEntry 37 }
raqmonParticipantNetOwdMean OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Mean Network one-way delay over the entire session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.12 of the [RFC4710]"
::= { raqmonParticipantEntry 38 }
Siddiqui, et al. Standards Track [Page 19]
RFC 4711 RAQMON MIB October 2006
raqmonParticipantNetOwdMin OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Minimum Network one-way delay over the entire session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.12 of the [RFC4710]"
::= { raqmonParticipantEntry 39 }
raqmonParticipantNetOwdMax OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum Network one-way delay over the entire session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.1 of the [RFC4710]"
::= { raqmonParticipantEntry 40 }
raqmonParticipantAppDelayMean OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Mean application delay over the entire session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.13 of the [RFC4710]"
::= { raqmonParticipantEntry 41 }
raqmonParticipantAppDelayMin OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Minimum application delay over the entire session.
If the value was not reported to the collector,
this object will have the value -1."
Siddiqui, et al. Standards Track [Page 20]
RFC 4711 RAQMON MIB October 2006
REFERENCE
"Section 5.13 of the [RFC4710]"
::= { raqmonParticipantEntry 42 }
raqmonParticipantAppDelayMax OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum application delay over the entire session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.13 of the [RFC4710]"
::= { raqmonParticipantEntry 43 }
raqmonParticipantPacketsRcvd OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of packets received for the entire session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.16 of the [RFC4710]"
::= { raqmonParticipantEntry 44 }
raqmonParticipantPacketsSent OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of packets sent for the entire session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.17 of the [RFC4710]"
::= { raqmonParticipantEntry 45 }
raqmonParticipantOctetsRcvd OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "Octets"
MAX-ACCESS read-only
STATUS current
Siddiqui, et al. Standards Track [Page 21]
RFC 4711 RAQMON MIB October 2006
DESCRIPTION
"Count of octets received for the entire session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.18 of the [RFC4710]"
::= { raqmonParticipantEntry 46 }
raqmonParticipantOctetsSent OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "Octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of octets sent for the entire session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.19 of the [RFC4710]"
::= { raqmonParticipantEntry 47 }
raqmonParticipantLostPackets OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of packets lost by this receiver for the entire
session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.20 of the [RFC4710]"
::= { raqmonParticipantEntry 48 }
raqmonParticipantLostPacketsFrct OBJECT-TYPE
SYNTAX Integer32 (-1|0..100)
UNITS "percents"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Fraction of lost packets out of total packets received.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.21 of the [RFC4710]"
::= { raqmonParticipantEntry 49 }
Siddiqui, et al. Standards Track [Page 22]
RFC 4711 RAQMON MIB October 2006
raqmonParticipantDiscards OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of packets discarded by this receiver for the
entire session.
If the value was not reported to the collector,
this object will have the value -1."
REFERENCE
"Section 5.22 of the [RFC4710]"
::= { raqmonParticipantEntry 50 }
raqmonParticipantDiscardsFrct OBJECT-TYPE
SYNTAX Integer32 (-1|0..100)
UNITS "percents"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Fraction of discarded packets out of total packets
received. If the value was not reported to the
collector, this object will have the value -1."
REFERENCE
"Section 5.23 of the [RFC4710]"
::= { raqmonParticipantEntry 51 }
raqmonQosTable OBJECT-TYPE
SYNTAX SEQUENCE OF RaqmonQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of historical information about quality-of-service
data during sessions."
::= { raqmonSession 2 }
raqmonQosEntry OBJECT-TYPE
SYNTAX RaqmonQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains information from a single RAQMON
packet, related to a single session
(application) run by one participant.
Indexation by the start time of the session aims
to ease sorting by management applications. Agents MUST
NOT report identical start times for any two sessions
Siddiqui, et al. Standards Track [Page 23]
RFC 4711 RAQMON MIB October 2006
on the same host.
Rows are removed for inactive sessions when
implementation-specific time or space limits are
reached."
INDEX { raqmonParticipantStartDate,
raqmonParticipantIndex,
raqmonQosTime }
::= { raqmonQosTable 1 }
RaqmonQosEntry ::=
SEQUENCE {
raqmonQosTime Unsigned32,
raqmonQoSEnd2EndNetDelay Integer32,
raqmonQoSInterArrivalJitter Integer32,
raqmonQosRcvdPackets Integer32,
raqmonQosRcvdOctets Integer32,
raqmonQosSentPackets Integer32,
raqmonQosSentOctets Integer32,
raqmonQosLostPackets Integer32,
raqmonQosSessionStatus SnmpAdminString
}
raqmonQosTime OBJECT-TYPE
SYNTAX Unsigned32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Time of this entry measured from the start of the
corresponding participant session."
::= { raqmonQosEntry 1 }
raqmonQoSEnd2EndNetDelay OBJECT-TYPE
SYNTAX Integer32 (-1 | 0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The round-trip time.
Will contain the previous value if there was no report
for this time, or -1 if the value has never
been reported."
REFERENCE
"Section 5.11 of the [RFC4710]"
::= { raqmonQosEntry 2 }
raqmonQoSInterArrivalJitter OBJECT-TYPE
SYNTAX Integer32 (-1 | 0..2147483647)
Siddiqui, et al. Standards Track [Page 24]
RFC 4711 RAQMON MIB October 2006
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An estimate of delay variation as observed by this
receiver. Will contain the previous value if there
was no report for this time, or -1 if the value
has never been reported."
REFERENCE
"Section 5.14 of the [RFC4710]"
::= { raqmonQosEntry 3 }
raqmonQosRcvdPackets OBJECT-TYPE
SYNTAX Integer32 (-1 | 0..2147483647)
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of packets received by this receiver since the
previous entry. Will contain the previous value if
there was no report for this time, or -1 if the value
has never been reported."
REFERENCE
"Section 5.16 of the [RFC4710]"
::= { raqmonQosEntry 4 }
raqmonQosRcvdOctets OBJECT-TYPE
SYNTAX Integer32 (-1 | 0..2147483647)
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of octets received by this receiver since the
previous report. Will contain the previous value if
there was no report for this time, or -1 if the value
has never been reported."
REFERENCE
"Section 5.18 of the [RFC4710]"
::= { raqmonQosEntry 5 }
raqmonQosSentPackets OBJECT-TYPE
SYNTAX Integer32 (-1 | 0..2147483647)
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of packets sent since the previous report.
Will contain the previous value if there
Siddiqui, et al. Standards Track [Page 25]
RFC 4711 RAQMON MIB October 2006
was no report for this time, or -1 if the value
has never been reported."
REFERENCE
"Section 5.17 of the [RFC4710]"
::= { raqmonQosEntry 6 }
raqmonQosSentOctets OBJECT-TYPE
SYNTAX Integer32 (-1 | 0..2147483647)
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of octets sent since the previous report.
Will contain the previous value if there
was no report for this time, or -1 if the value
has never been reported."
REFERENCE
"Section 5.19 of the [RFC4710]"
::= { raqmonQosEntry 7 }
raqmonQosLostPackets OBJECT-TYPE
SYNTAX Integer32 (-1 | 0..2147483647)
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of packets lost as observed by this receiver
since the previous report. Will contain the previous
value if there was no report for this time, or -1 if
the value has never been reported."
REFERENCE
"Section 5.20 of the [RFC4710]"
::= { raqmonQosEntry 8 }
raqmonQosSessionStatus OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The session status. Will contain the previous value
if there was no report for this time or the zero-length
string if no value was ever reported."
REFERENCE
"Section 5.10 of the [RFC4710]"
::= { raqmonQosEntry 9 }
raqmonParticipantAddrTable OBJECT-TYPE
Siddiqui, et al. Standards Track [Page 26]
RFC 4711 RAQMON MIB October 2006
SYNTAX SEQUENCE OF RaqmonParticipantAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Maps raqmonParticipantAddr to the index of the
raqmonParticipantTable. This table allows
management applications to find entries
sorted by raqmonParticipantAddr rather than
raqmonParticipantStartDate."
::= { raqmonSession 3 }
raqmonParticipantAddrEntry OBJECT-TYPE
SYNTAX RaqmonParticipantAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to exactly one entry in the
raqmonParticipantEntry: the entry containing the
index pair raqmonParticipantStartDate,
raqmonParticipantIndex.
Note that there is no concern about the indexation of
this table exceeding the limits defined by RFC 2578,
Section 3.5. According to [RFC4710], Section
5.1, only IPv4 and IPv6 addresses can be reported as
participant addresses."
INDEX { raqmonParticipantAddrType,
raqmonParticipantAddr,
raqmonParticipantStartDate,
raqmonParticipantIndex }
::= { raqmonParticipantAddrTable 1 }
RaqmonParticipantAddrEntry ::=
SEQUENCE { raqmonParticipantAddrEndDate DateAndTime }
raqmonParticipantAddrEndDate OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of raqmonParticipantEndDate for the
corresponding raqmonParticipantEntry."
::= { raqmonParticipantAddrEntry 1 }
raqmonException OBJECT IDENTIFIER ::= { raqmonMIBObjects 2 }
raqmonSessionExceptionTable OBJECT-TYPE
Siddiqui, et al. Standards Track [Page 27]
RFC 4711 RAQMON MIB October 2006
SYNTAX SEQUENCE OF RaqmonSessionExceptionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table defines thresholds for the management
station to get notifications about sessions that
encountered poor quality of service.
The information in this table MUST be persistent
across agent reboots."
::= { raqmonException 2 }
raqmonSessionExceptionEntry OBJECT-TYPE
SYNTAX RaqmonSessionExceptionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the raqmonSessionExceptionTable."
INDEX { raqmonSessionExceptionIndex }
::= { raqmonSessionExceptionTable 1 }
RaqmonSessionExceptionEntry ::=
SEQUENCE {
raqmonSessionExceptionIndex Unsigned32,
raqmonSessionExceptionIAJitterThreshold Unsigned32,
raqmonSessionExceptionNetRTTThreshold Unsigned32,
raqmonSessionExceptionLostPacketsThreshold Unsigned32,
raqmonSessionExceptionRowStatus RowStatus
}
raqmonSessionExceptionIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an
entry in the raqmonSessionExceptionTable.
Management applications can determine unused indices
by performing GetNext or GetBulk operations on the
Table."
::= { raqmonSessionExceptionEntry 2 }
raqmonSessionExceptionIAJitterThreshold OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Siddiqui, et al. Standards Track [Page 28]
RFC 4711 RAQMON MIB October 2006
"Threshold for jitter.
The value during a session must be greater than or
equal to this value for an exception to be created."
::= { raqmonSessionExceptionEntry 3 }
raqmonSessionExceptionNetRTTThreshold OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Threshold for round-trip time.
The value during a session must be greater than or
equal to this value for an exception to be created."
::= { raqmonSessionExceptionEntry 4 }
raqmonSessionExceptionLostPacketsThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..1000)
UNITS "tenth of a percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Threshold for lost packets in units of tenths
of a percent. The value during a session must
be greater than or equal to this value for an
exception to be created."
::= { raqmonSessionExceptionEntry 5 }
raqmonSessionExceptionRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object has a value of 'active' when
exceptions are being monitored by the system.
A newly-created conceptual row must have all
the read-create objects initialized before
becoming 'active'. A conceptual row that is in
the 'notReady' or 'notInService' state MAY be
removed after 5 minutes. No writeable objects
can be changed while the row is active."
::= { raqmonSessionExceptionEntry 7 }
raqmonConfig OBJECT IDENTIFIER ::= { raqmonMIBObjects 3 }
raqmonConfigPort OBJECT-TYPE
SYNTAX InetPortNumber
Siddiqui, et al. Standards Track [Page 29]
RFC 4711 RAQMON MIB October 2006
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The UDP port to listen on for RAQMON reports,
running on transport protocols other than SNMP.
If the RAQMON PDU transport protocol is SNMP,
a write operation on this object has no effect, as
the standard port 162 is always used.
The value of this object MUST be persistent across
agent reboots."
::= { raqmonConfig 1 }
raqmonConfigPduTransport OBJECT-TYPE
SYNTAX BITS
{
other(0),
tcp(1),
snmp(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The PDU transport(s) used by this collector.
If other(0) is set, the collector supports a
transport other than SNMP or TCP.
If tcp(1) is set, the collector supports TCP as a
transport protocol.
If snmp(2) is set, the collector supports SNMP as a
transport protocol."
::= { raqmonConfig 2 }
raqmonConfigRaqmonPdus OBJECT-TYPE
SYNTAX Counter32
UNITS "PDUs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of RAQMON PDUs received by the Collector."
::= { raqmonConfig 3 }
raqmonConfigRDSTimeout OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of seconds since the reception of the
last RAQMON PDU from a RDS after which a session
Siddiqui, et al. Standards Track [Page 30]
RFC 4711 RAQMON MIB October 2006
between the respective RDS and the collector will be
considered terminated.
The value of this object MUST be persistent across
agent reboots."
::= { raqmonConfig 4 }
raqmonConformance OBJECT IDENTIFIER ::= { raqmonMIB 2 }
raqmonCompliances OBJECT IDENTIFIER ::= { raqmonConformance 1 }
raqmonGroups OBJECT IDENTIFIER ::= { raqmonConformance 2 }
raqmonCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Describes the requirements for conformance to the
RAQMON MIB."
MODULE -- this module
MANDATORY-GROUPS { raqmonCollectorGroup,
raqmonCollectorNotificationsGroup
}
OBJECT raqmonParticipantAddrType
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
DESCRIPTION
"Only IPv4 and IPv6 addresses need to be supported."
OBJECT raqmonParticipantAddr
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"Only IPv4 and IPv6 addresses need to be supported."
OBJECT raqmonParticipantPeerAddrType
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
DESCRIPTION
"Only IPv4 and IPv6 addresses need to be supported."
OBJECT raqmonParticipantPeerAddr
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"Only IPv4 and IPv6 addresses need to be supported."
::= { raqmonCompliances 1 }
Siddiqui, et al. Standards Track [Page 31]
RFC 4711 RAQMON MIB October 2006
raqmonCollectorGroup OBJECT-GROUP
OBJECTS {
raqmonParticipantReportCaps,
raqmonParticipantAddrType,
raqmonParticipantAddr,
raqmonParticipantSendPort,
raqmonParticipantRecvPort,
raqmonParticipantSetupDelay,
raqmonParticipantName,
raqmonParticipantAppName,
raqmonParticipantQosCount,
raqmonParticipantEndDate,
raqmonParticipantDestPayloadType,
raqmonParticipantSrcPayloadType,
raqmonParticipantActive,
raqmonParticipantPeer,
raqmonParticipantPeerAddrType,
raqmonParticipantPeerAddr,
raqmonParticipantSrcL2Priority,
raqmonParticipantDestL2Priority,
raqmonParticipantSrcDSCP,
raqmonParticipantDestDSCP,
raqmonParticipantCpuMean,
raqmonParticipantCpuMin,
raqmonParticipantCpuMax,
raqmonParticipantMemoryMean,
raqmonParticipantMemoryMin,
raqmonParticipantMemoryMax,
raqmonParticipantNetRTTMean,
raqmonParticipantNetRTTMin,
raqmonParticipantNetRTTMax,
raqmonParticipantIAJitterMean,
raqmonParticipantIAJitterMin,
raqmonParticipantIAJitterMax,
raqmonParticipantIPDVMean,
raqmonParticipantIPDVMin,
raqmonParticipantIPDVMax,
raqmonParticipantNetOwdMean,
raqmonParticipantNetOwdMin,
raqmonParticipantNetOwdMax,
raqmonParticipantAppDelayMean,
raqmonParticipantAppDelayMin,
raqmonParticipantAppDelayMax,
raqmonParticipantPacketsRcvd,
raqmonParticipantPacketsSent,
raqmonParticipantOctetsRcvd,
raqmonParticipantOctetsSent,
raqmonParticipantLostPackets,
Siddiqui, et al. Standards Track [Page 32]
RFC 4711 RAQMON MIB October 2006
raqmonParticipantLostPacketsFrct,
raqmonParticipantDiscards,
raqmonParticipantDiscardsFrct,
raqmonQoSEnd2EndNetDelay,
raqmonQoSInterArrivalJitter,
raqmonQosRcvdPackets,
raqmonQosRcvdOctets,
raqmonQosSentPackets,
raqmonQosSentOctets,
raqmonQosLostPackets,
raqmonQosSessionStatus,
raqmonParticipantAddrEndDate,
raqmonConfigPort,
raqmonSessionExceptionIAJitterThreshold,
raqmonSessionExceptionNetRTTThreshold,
raqmonSessionExceptionLostPacketsThreshold,
raqmonSessionExceptionRowStatus,
raqmonConfigPduTransport,
raqmonConfigRaqmonPdus,
raqmonConfigRDSTimeout}
STATUS current
DESCRIPTION
"Objects used in RAQMON by a collector."
::= { raqmonGroups 1 }
raqmonCollectorNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS { raqmonSessionAlarm }
STATUS current
DESCRIPTION
"Notifications emitted by a RAQMON collector."
::= { raqmonGroups 2 }
END
6. Security Considerations
There are a number of management objects defined in this MIB module
with a MAX-ACCESS clause of read-write. Such objects may be
considered sensitive or vulnerable in some network environments. The
support for SET operations in a non-secure environment without proper
protection can have a negative effect on network operations.
Setting the value of the object raqmonRDSTimeout to too low a value
would result in RDS sessions being terminated sooner than necessary,
while setting at too high a value may result in terminated sessions
continuing to be managed, with unnecessary memory allocations.
Siddiqui, et al. Standards Track [Page 33]
RFC 4711 RAQMON MIB October 2006
Setting the following object to incorrect values can result in the
collectors either flooding the management applications with
unnecessary notifications, or not sending notifications when the QoS
in the network may be degraded.
raqmonSessionExceptionIAJitterThreshold
raqmonSessionExceptionRTTThreshold
raqmonSessionExceptionLostPacketsThreshold
Setting the raqmonConfigPort object to incorrect values can result in
the collector not being able to receive RAQMON PDUs from the data
sources.
Some of the readable objects in this MIB module (i.e., objects with a
MAX-ACCESS other than not-accessible) may be considered sensitive or
vulnerable in some network environments. These are:
raqmonParticipantTable
raqmonQoSTable
raqmonParticpantAddrTable
Unauthorized exposure of these objects may lead to disclosure of the
addresses of the participants in applications, or information about
the traffic patents of the applications, which may be considered
sensitive in certain environments.
It is thus important to control even GET and/or NOTIFY access to
these objects and possibly to even encrypt their values when sending
them over the network via SNMP.
The structure of the RAQMON tables limits what can be usefully done
for access control configuration using View-based Access Control
Model (VACM). For example, with these structures it would not be
possible to provide a group, with access to performance data for a
specific group of devices, since the index values for
raqmonParticpantEntry cannot be known in advance. Likewise,
raqmonSessionExceptionEntries apply to all entries in the
raqmonQoSTable.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPsec),
even then, there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete) the objects
in this MIB module.
Siddiqui, et al. Standards Track [Page 34]
RFC 4711 RAQMON MIB October 2006
It is RECOMMENDED that implementers consider the security features as
provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
7. IANA Considerations
No requirements from IANA are defined in this document. The root OID
of the MIB module defined in this document belongs to the RMON
subtree, as reserved in [RFC3737].
8. Acknowledgements
Richard Smith created the first proprietary version of this MIB.
The authors would also like to thank all the participants in the
Remote Monitoring MIB Working Group, and especially Andy Bierman,
Steven Waldbusser, Alan Clark, Itai Zilbershtein, and Robert Cole for
interesting discussions, ideas, comments, and direct contributions to
this work.
The authors would also like to thank Randy Presuhn for the precious
technical comments, as well as for the laborious activity of
reviewing the syntax and spelling of the document.
The authors would like to thank Bert Wijnen for the review of the
final versions of the document, as well as for the guidance provided
during the whole period of editing.
Siddiqui, et al. Standards Track [Page 35]
RFC 4711 RAQMON MIB October 2006
9. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578, April
1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Textual Conventions for
SMIv2", STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Conformance Statements for
SMIv2", STD 58, RFC 2580, April 1999.
[RFC2819] Waldbusser, S., "Remote Network Monitoring Management
Information Base", STD 59, RFC 2819, May 2000.
[RFC3411] Harrington, D., Preshun, R., and B. Wijnen, "An
Architecture for Describing Simple Network Management
Protocol (SNMP) Management Frameworks", STD 62, RFC 3411,
December 2002.
[RFC4001] Daniele, M., Haberman, B., Routhier, S., and J.
Schoenwalder, "Textual Conventions for Internet Network
Addresses", RFC 4001, February 2005.
[RFC4710] Siddiqui, A., Romascanu, D., and E. Golovinsky, "Real-
time Application Quality-of-Service Monitoring (RAQMON)
Framework", RFC 4710, October 2006.
10. Informative References
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410, December 2002.
[RFC4712] Siddiqui, A., Romascanu, D., Golovinsky, E., Ramhman, M.,
and Y. Kim, "Transport Mappings for Real-time Application
Quality-of-Service Monitoring (RAQMON) Protocol Data Unit
(PDU)", RFC 4712, October 2006.
[RFC3737] Wijnen, B. and A. Bierman, "IANA Guidelines for the
Registry of Remote Monitoring (RMON) MIB modules", RFC
3737, April 2004.
Siddiqui, et al. Standards Track [Page 36]
RFC 4711 RAQMON MIB October 2006
Authors' Addresses
Anwar A. Siddiqui
Avaya Labs
307 Middletown Lincroft Road
Lincroft, New Jersey 07738
USA
Phone: +1 732 852-3200
Fax: +1 732 817-5922
EMail: anwars@avaya.com
Dan Romascanu
Avaya
Atidim Technology Park, Bldg. #3
Tel Aviv, 61131
Israel
Phone: +972 3-645-8414
EMail: dromasca@avaya.com
Eugene Golovinsky
EMail: gene@alertlogic.net
Siddiqui, et al. Standards Track [Page 37]
RFC 4711 RAQMON MIB October 2006
Full Copyright Statement
Copyright (C) The Internet Society (2006).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgement
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
Siddiqui, et al. Standards Track [Page 38]