RFC5833: Control and Provisioning of Wireless Access Points (CAPWAP) Protocol Base MIB
Download in PDF format Download in text format
Related keywords:
(CAPWAP-BASE-MIB)
(MIB)
Internet Engineering Task Force (IETF) Y. Shi, Ed.
Request for Comments: 5833 Hangzhou H3C Tech. Co., Ltd.
Category: Informational D. Perkins, Ed.
ISSN: 2070-1721 C. Elliott, Ed.
Y. Zhang, Ed.
Fortinet, Inc.
May 2010
Control and Provisioning of Wireless Access Points (CAPWAP) Protocol
Base MIB
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols. In particular, it
describes the managed objects for modeling the Control And
Provisioning of Wireless Access Points (CAPWAP) Protocol. This MIB
module is presented as a basis for future work on the SNMP management
of the CAPWAP protocol.
Status of This Memo
This document is not an Internet Standards Track specification; it is
published for informational purposes.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Not all documents
approved by the IESG are a candidate for any level of Internet
Standard; see Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc5833.
Shi, et al. Informational [Page 1]
RFC 5833 CAPWAP Protocol Base MIB May 2010
Copyright Notice
Copyright (c) 2010 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. The Internet-Standard Management Framework . . . . . . . . . . 3
3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
4. Conventions . . . . . . . . . . . . . . . . . . . . . . . . . 4
5. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5.1. Requirements and Constraints . . . . . . . . . . . . . . . 5
5.2. Wireless Binding MIB Modules . . . . . . . . . . . . . . . 5
5.3. Design Objectives . . . . . . . . . . . . . . . . . . . . 5
5.4. Design Idea . . . . . . . . . . . . . . . . . . . . . . . 6
5.5. Mechanism of Reusing Wireless Binding MIB Modules . . . . 6
5.6. CAPWAP Protocol Wireless Binding MIB Module . . . . . . . 7
5.7. WTP Profile . . . . . . . . . . . . . . . . . . . . . . . 7
6. Structure of the MIB Module . . . . . . . . . . . . . . . . . 8
7. Relationship to Other MIB Modules . . . . . . . . . . . . . . 9
7.1. Relationship to SNMPv2-MIB Module . . . . . . . . . . . . 9
7.2. Relationship to IF-MIB Module . . . . . . . . . . . . . . 9
7.3. Relationship to ENTITY-MIB Module . . . . . . . . . . . . 10
7.4. Relationship to Wireless Binding MIB Modules . . . . . . . 10
7.5. MIB Modules Required for IMPORTS . . . . . . . . . . . . . 10
8. Example of CAPWAP-BASE-MIB Module Usage . . . . . . . . . . . 10
9. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 14
10. Security Considerations . . . . . . . . . . . . . . . . . . . 69
11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 70
11.1. IANA Considerations for CAPWAP-BASE-MIB Module . . . . . . 70
11.2. IANA Considerations for ifType . . . . . . . . . . . . . . 70
12. Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 70
13. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 71
14. References . . . . . . . . . . . . . . . . . . . . . . . . . . 71
14.1. Normative References . . . . . . . . . . . . . . . . . . . 71
14.2. Informative References . . . . . . . . . . . . . . . . . . 72
Shi, et al. Informational [Page 2]
RFC 5833 CAPWAP Protocol Base MIB May 2010
1. Introduction
The CAPWAP Protocol [RFC5415] defines a standard, interoperable
protocol, which enables an Access Controller (AC) to manage a
collection of Wireless Termination Points (WTPs).
This document defines a MIB module that can be used to manage the
CAPWAP implementations. This MIB module covers both configuration
and WTP status-monitoring aspects of CAPWAP, and provides a way to
reuse MIB modules for any wireless technology. It presented as a
basis for future work on a SNMP management of the CAPWAP protocol.
2. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579], and STD 58, RFC 2580
[RFC2580].
3. Terminology
This document uses terminology from the CAPWAP Protocol specification
[RFC5415] and the Architecture Taxonomy for CAPWAP [RFC4118].
Access Controller (AC): The network entity that provides WTP access
to the network infrastructure in the data plane, control plane,
management plane, or a combination therein.
Wireless Termination Point (WTP): The physical or network entity that
contains an radio frequency (RF) antenna and wireless physical layer
(PHY) to transmit and receive station traffic for wireless access
networks.
Control And Provisioning of Wireless Access Points (CAPWAP): It is a
generic protocol defining AC and WTP control and data plane
communication via a CAPWAP protocol transport mechanism. CAPWAP
control messages, and optionally CAPWAP data messages, are secured
using Datagram Transport Layer Security (DTLS) [RFC4347].
Shi, et al. Informational [Page 3]
RFC 5833 CAPWAP Protocol Base MIB May 2010
CAPWAP Control Channel: A bi-directional flow defined by the AC IP
Address, WTP IP Address, AC control port, WTP control port, and the
transport-layer protocol (UDP or UDP-Lite) over which CAPWAP control
packets are sent and received.
CAPWAP Data Channel: A bi-directional flow defined by the AC IP
Address, WTP IP Address, AC data port, WTP data port, and the
transport-layer protocol (UDP or UDP-Lite) over which CAPWAP data
packets are sent and received.
Station (STA): A device that contains an interface to a wireless
medium (WM).
Split and Local MAC: The CAPWAP protocol supports two modes of
operation: Split and Local MAC (medium access control). In Split MAC
mode, all Layer 2 wireless data and management frames are
encapsulated via the CAPWAP protocol and exchanged between the AC and
the WTPs. The Local MAC mode allows the data frames to be either
locally bridged or tunneled as 802.3 frames.
Wireless Binding: The CAPWAP protocol is independent of a specific
WTP radio technology, as well its associated wireless link-layer
protocol. Elements of the CAPWAP protocol are designed to
accommodate the specific needs of each wireless technology in a
standard way. Implementation of the CAPWAP protocol for a particular
wireless technology MUST define a binding protocol for it, e.g., the
binding for IEEE 802.11, provided in [RFC5416].
Autonomous Wireless Local Area Network (WLAN) Architecture: It is the
traditional autonomous WLAN architecture, in which each WTP is a
single physical device that implements all the wireless services.
Centralized WLAN Architecture: It is an emerging hierarchical
architecture utilizing one or more centralized controllers for
managing a large number of WTP devices. It can be said that the full
wireless functions are implemented across multiple physical network
devices, namely, the WTPs and ACs.
4. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Shi, et al. Informational [Page 4]
RFC 5833 CAPWAP Protocol Base MIB May 2010
5. Overview
5.1. Requirements and Constraints
The CAPWAP Protocol MIB module (CAPWAP-BASE-MIB) is designed to:
- Support centralized management and monitoring of WTPs from the AC
in combination with the CAPWAP protocol;
- Allow operators to make configurations for WTPs before and after
they connect to the AC;
- Support querying of CAPWAP protocol parameters;
- Support displaying of WTPs' current states and configurations;
- Provide basic property information about the AC, WTPs, radios, and
stations, and their relationships;
- Provide counters for events on WTPs and radios such as reboot and
hardware failure;
- Provide various notifications such as channel up and join failure.
5.2. Wireless Binding MIB Modules
Other Standards Development Organizations (SDOs), such as IEEE, have
already defined MIB modules for a specific wireless technology, e.g.,
IEEE 802.11 MIB module [IEEE.802-11.2007]. Such MIB modules are
called wireless binding MIB modules.
5.3. Design Objectives
This document introduces a mechanism to avoid redefining MIB objects
in the existing MIB modules for a specific wireless technology, in
other words, a mechanism to reuse wireless binding MIB modules
defined by other SDOs.
In summary, the CAPWAP-BASE-MIB module has the following design
objectives:
- To implement an architecture that uses SNMP for the management and
control of wireless networks, and answering the operator's
requirements for centralized management, whatever the wireless
devices are configured and deployed (centralized, autonomous, or
some mix);
- To be consistent with the CAPWAP protocol;
Shi, et al. Informational [Page 5]
RFC 5833 CAPWAP Protocol Base MIB May 2010
- To be independent of any wireless technologies and be able to
reuse wireless binding MIB modules defined by other SDOs;
- To enable interoperability between vendors;
- To meet the management requirements for the centralized WLAN
architecture.
5.4. Design Idea
The basic design idea of the CAPWAP-BASE-MIB module is:
- The SNMP agent MUST be run on the AC devices and is not REQUIRED
on the WTP devices. It follows the same model as the CAPWAP
protocol: Centralized Control.
- It is designed to accommodate the specific needs of each wireless
technology in a standard way. It is independent of any wireless
technologies.
- The ifIndex [RFC2863] is used as a common index for corresponding
interfaces in the CAPWAP-BASE-MIB and the MIB modules of specific
wireless technologies.
- The operator could manage and control the centralized WLAN
architectures using multiple MIB modules defined by multiple SDOs,
while keeping them loosely coupled.
5.5. Mechanism of Reusing Wireless Binding MIB Modules
For any wireless technology, the configuration and management of
radios are very important. As usual, wireless binding MIB modules
support radio management on their own. For example, the MIB tables
such as the dot11OperationTable [IEEE.802-11.2007] are able to
support WTP radio configuration. These tables use the ifIndex as the
index, and work well under autonomous WLAN architecture.
To reuse such wireless binding MIB modules is very important to
centralized WLAN architectures. According to [RFC5415], a specific
PHY radio could be identified by the combination of the identifiers
of the WTP and radio (WTP ID + Radio ID), so the key point is to make
use of the ifIndex idea and find a way to maintain the mappings
between 'WTP ID + radio ID' and the ifIndex. As a generic mechanism,
an ifIndex can identify an interface in an abstract way, and it does
NOT care for the interface's PHY location (either on the WTP or AC).
The AC can have WTP Virtual Radio Interfaces to logically represent
PHY radios on the WTP. From the operator's perspective, it appears
that PHY radios are located on the AC, and the PHY location of the
Shi, et al. Informational [Page 6]
RFC 5833 CAPWAP Protocol Base MIB May 2010
WTP (radio) is hidden. The operator can operate radios through MIB
tables with the ifIndex of a WTP Virtual Radio Interface. As a type
of abstract interface, the WTP Virtual Radio Interface could be used
by any wireless technology such as IEEE 802.11 and 802.16. The
capwapBaseWirelessBindingTable in the CAPWAP-BASE-MIB module is used
to store the mappings between the 'WTP ID + Radio ID' and the
ifIndex.
5.6. CAPWAP Protocol Wireless Binding MIB Module
According to the CAPWAP Protocol specification [RFC5415], when
defining a binding for wireless technologies, the authors MUST
include any necessary definitions for technology-specific messages
and all technology-specific message elements for those messages. A
CAPWAP binding protocol is required for a specific wireless binding
technology, e.g., the protocol of [RFC5416] for IEEE 802.11 binding.
Sometimes, not all the technology-specific message elements in a
CAPWAP binding protocol have MIB objects defined by other SDOs. For
example, the protocol of [RFC5416] defines WLAN management. The WLAN
refers to a logical component instantiated on a WTP device. A single
physical WTP MAY operate a number of WLANs. Also, Local or Split MAC
modes could be specified for a WLAN. The MAC mode for a WLAN is not
in the scope of IEEE 802.11 [IEEE.802-11.2007]. In such cases, in
addition to the existing wireless binding MIB modules defined by
other SDOs, a CAPWAP protocol wireless binding MIB module is required
to be defined for a wireless binding, e.g, the CAPWAP Protocol
Binding MIB for IEEE 802.11 [RFC5834].
5.7. WTP Profile
In a centralized WLAN architecture, a WTP profile is used to make
configurations such as a static IP address for a WTP before and after
it connects to the AC. It MUST contain the Base MAC address
[RFC5415] of the WTP because the CAPWAP message received from the WTP
contains the Base MAC address and the AC uses this Base MAC address
to find the corresponding WTP profile.
Section 4.6.40 of [RFC5415] omits indicating that the WTP's Base MAC
address MUST be included in the WTP Board Data message element. This
is a known errata item [Err1832] and should be fixed in any future
revision of RFC 5415.
Another important function of WTP profile is to trigger the creation
of WTP Virtual Radio Interfaces on the AC. To implement this
function, a WTP profile MUST include the WTP's model number
[RFC5415], which reflects the number of PHY radios on the WTP. In
this way, the creation of a WTP profile triggers the AC to
Shi, et al. Informational [Page 7]
RFC 5833 CAPWAP Protocol Base MIB May 2010
automatically create the same number of WTP Virtual Radio Interfaces
corresponding to the WTP's PHY radios without manual intervention.
With the ifIndexes of WTP Virtual Radio Interfaces, the operator
could configure and manage the WTP's PHY radios through the wireless
binding MIB modules.
6. Structure of the MIB Module
The MIB objects are derived from the CAPWAP protocol document
[RFC5415].
1) capwapBaseAcNameListTable
The AC name list table is used to configure the AC name list.
2) capwapBaseMacAclTable
The ACL table is used to configure stations' Access Control Lists
(ACLs).
3) capwapBaseWtpProfileTable
The WTP profile table is used to configure WTP profiles for WTPs
to be managed before they connect to the AC. An operator could
change a WTP's current configuration by changing the values of
parameters in the corresponding WTP profile, then the WTP could
get the new configuration through the CAPWAP control channel.
4) capwapBaseWtpStateTable
The state table of WTPs is used to indicate the AC's CAPWAP FSM
state for each WTP, and helps the operator to query a WTP's
current configuration.
5) capwapBaseWtpTable
The WTP table is used to display properties of the WTPs in running
state.
6) capwapBaseWirelessBindingTable
The wireless binding table is used to display the mappings between
WTP Virtual Radio Interfaces and PHY radios, and the wireless
binding type for each PHY radio.
Shi, et al. Informational [Page 8]
RFC 5833 CAPWAP Protocol Base MIB May 2010
7) capwapBaseStationTable
The station table is used for providing stations' basic property
information.
8) capwapBaseWtpEventsStatsTable
The WTP events statistic table is used for collecting WTP reboot
count, link failure count, hardware failure count and so on.
9) capwapBaseRadioEventsStatsTable
The radio events statistic table is used for collecting radio
reset count, channel change count, hardware failure count, and so
on.
7. Relationship to Other MIB Modules
7.1. Relationship to SNMPv2-MIB Module
The CAPWAP-BASE-MIB module does not duplicate the objects of the
'system' group in the SNMPv2-MIB [RFC3418] that is defined as being
mandatory for all systems, and the objects apply to the entity as a
whole. The 'system' group provides identification of the management
entity and certain other system-wide data.
7.2. Relationship to IF-MIB Module
The Interfaces Group [RFC2863] defines generic managed objects for
managing interfaces. This memo contains the media-specific
extensions to the Interfaces Group for managing WTP PHY radios that
are modeled as interfaces.
The IF-MIB module is required to be supported on the AC. Each PHY
radio on the WTP corresponds to a WTP Virtual Radio Interface on the
AC. The WTP Virtual Radio Interface provides a way to configure the
radio's parameters and query radio's traffic statistics, and reuse
wireless binding modules defined by other SDOs. The interface MUST
be modeled as an ifEntry, and ifEntry objects such as ifIndex,
ifDescr, ifName, and ifAlias are to be used as per [RFC2863].
Also, as an ifIndex [RFC2863] is used as a common index for
corresponding interfaces in the CAPWAP-BASE-MIB and specific wireless
technologies MIB modules, the AC MUST have a mechanism that preserves
the values of the ifIndexes in the ifTable at AC reboot.
Shi, et al. Informational [Page 9]
RFC 5833 CAPWAP Protocol Base MIB May 2010
7.3. Relationship to ENTITY-MIB Module
The ENTITY-MIB module [RFC4133] meets the need for a standardized way
of representing a single agent that supports multiple instances of
one MIB. It could express a certain relationship between multiple
entities and provide entity properties for each entity.
In a centralized WLAN architecture, the SNMP agent runs on the AC and
is not required on the WTP. With the ENTITY-MIB module on the AC, it
could keep entity information such as firmware revision and software
revision of the AC and WTPs. From the ENTITY-MIB module's
perspective, the overall physical entity (AC) is a 'compound' of
multiple physical entities (that is, the WTPs connected to AC), and
all entities are each identified by a physical index. The
capwapBaseWtpTable of the CAPWAP-BASE-MIB module uses the
capwapBaseWtpPhyIndex object to store the mappings of WTP object
between CAPWAP-BASE-MIB and ENTITY-MIB modules.
By querying both the CAPWAP-BASE-MIB and ENTITY-MIB modules,
operators could query the status and properties of the AC and WTPs.
For example, they could get a WTP's current status through the
CAPWAP-BASE-MIB module, and a WTP's software revision information
through the ENTITY-MIB module. The CAPWAP-BASE-MIB module does not
duplicate those objects defined in the ENTITY-MIB module.
7.4. Relationship to Wireless Binding MIB Modules
The wireless binding MIB module of a wireless technology (such as
[IEEE.802-11.2007]) is required to be supported on the AC. The
CAPWAP-BASE-MIB module is able to support any wireless binding.
Through the ifIndexes of WTP Virtual Radio Interfaces, it provides a
consistent and abstract way of reusing MIB objects in the wireless
binding MIB modules. The CAPWAP-BASE-MIB module does not duplicate
those objects defined in the wireless binding MIB modules.
7.5. MIB Modules Required for IMPORTS
The following MIB module IMPORTS objects from SYSAPPL-MIB [RFC2287],
SNMPv2-SMI [RFC2578], SNMPv2-TC [RFC2579], SNMPv2-CONF [RFC2580],
IF-MIB [RFC2863], SNMP-FRAMEWORK-MIB [RFC3411], INET-ADDRESS-MIB
[RFC4001], and ENTITY-MIB [RFC4133].
8. Example of CAPWAP-BASE-MIB Module Usage
Below, the IEEE 802.11 binding is used as an example of how the MIB
modules operate.
1) Create a WTP profile.
Shi, et al. Informational [Page 10]
RFC 5833 CAPWAP Protocol Base MIB May 2010
Suppose the WTP's Base MAC address is '00:01:01:01:01:00'. Create
the WTP profile as follows:
In capwapBaseWtpProfileTable
{
capwapBaseWtpProfileId = 1,
capwapBaseWtpProfileName = 'WTP Profile 123456',
capwapBaseWtpProfileWtpMacAddress = '00:01:01:01:01:00',
capwapBaseWtpProfileWtpModelNumber = 'WTP123',
capwapBaseWtpProfileWtpName = 'WTP 123456',
capwapBaseWtpProfileWtpLocation = 'office',
capwapBaseWtpProfileWtpStaticIpEnable = true(1),
capwapBaseWtpProfileWtpStaticIpType = ipv4(1),
capwapBaseWtpProfileWtpStaticIpAddress = '192.0.2.10',
capwapBaseWtpProfileWtpNetmask = '255.255.255.0',
capwapBaseWtpProfileWtpGateway = '192.0.2.1',
capwapBaseWtpProfileWtpFallbackEnable = true(1),
capwapBaseWtpProfileWtpEchoInterval = 30,
capwapBaseWtpProfileWtpIdleTimeout = 300,
capwapBaseWtpProfileWtpMaxDiscoveryInterval = 20,
capwapBaseWtpProfileWtpReportInterval = 120,
capwapBaseWtpProfileWtpStatisticsTimer = 120,
capwapBaseWtpProfileWtpEcnSupport = limited(0)
}
Suppose the WTP with model number 'WTP123' has one PHY radio,
which is identified by ID 1. The creation of this WTP profile
triggers the AC to automatically create a WTP Virtual Radio
Interface and add a new row object to the
capwapBaseWirelessBindingTable without manual intervention.
Suppose the ifIndex of the WTP Virtual Radio Interface is 10. The
following information is stored in the
capwapBaseWirelessBindingTable.
In capwapBaseWirelessBindingTable
{
capwapBaseWtpProfileId = 1,
capwapBaseWirelessBindingRadioId = 1,
capwapBaseWirelessBindingVirtualRadioIfIndex = 10,
capwapBaseWirelessBindingType = dot11(2)
}
The WTP Virtual Radio Interfaces on the AC correspond to the PHY
radios on the WTP. The WTP Virtual Radio Interface is modeled by
ifTable [RFC2863].
Shi, et al. Informational [Page 11]
RFC 5833 CAPWAP Protocol Base MIB May 2010
In ifTable
{
ifIndex = 10,
ifDescr = 'WTP Virtual Radio Interface',
ifType = 254,
ifMtu = 0,
ifSpeed = 0,
ifPhysAddress = '00:00:00:00:00:00',
ifAdminStatus = true(1),
ifOperStatus = false(0),
ifLastChange = 0,
ifInOctets = 0,
ifInUcastPkts = 0,
ifInDiscards = 0,
ifInErrors = 0,
ifInUnknownProtos = 0,
ifOutOctets = 0,
ifOutUcastPkts = 0,
ifOutDiscards = 0,
ifOutErrors = 0
}
2) Query the ifIndexes of WTP Virtual Radio Interfaces.
Before configuring PHY radios, the operator needs to get the
ifIndexes of WTP Virtual Radio Interfaces corresponding to the PHY
radios.
As capwapBaseWirelessBindingTable already stores the mappings
between PHY radios (Radio IDs) and the ifIndexes of WTP Virtual
Radio Interfaces, the operator can get the ifIndex information by
querying this table. Such a query operation SHOULD run from radio
ID 1 to radio ID 31 according to [RFC5415]), and stop when an
invalid ifIndex value (0) is returned.
This example uses capwapBaseWtpProfileId = 1 and
capwapBaseWirelessBindingRadioId = 1 as inputs to query the
capwapBaseWirelessBindingTable, and gets
capwapBaseWirelessBindingVirtualRadioIfIndex = 10. Then it uses
capwapBaseWtpProfileId = 1 and capwapBaseWirelessBindingRadioId =
2, and gets an invalid ifIndex value (0), so the query operation
ends. This method gets not only the ifIndexes of WTP Virtual
Radio Interfaces, but also the numbers of PHY radios. Besides
checking whether the ifIndex value is valid, the operator SHOULD
check whether the capwapBaseWirelessBindingType is the desired
binding type.
Shi, et al. Informational [Page 12]
RFC 5833 CAPWAP Protocol Base MIB May 2010
3) Configure specific wireless binding parameters for a WTP Virtual
Radio Interface.
This configuration is made on the AC through a specific wireless
binding MIB module such as the IEEE 802.11 MIB module.
The following shows an example of configuring parameters for a WTP
Virtual Radio Interface with ifIndex 10 through the IEEE 802.11
dot11OperationTable [IEEE.802-11.2007].
In dot11OperationTable
{
ifIndex = 10,
dot11MACAddress = '00:00:00:00:00:00',
dot11RTSThreshold = 2347,
dot11ShortRetryLimit = 7,
dot11LongRetryLimit = 4,
dot11FragmentationThreshold = 256,
dot11MaxTransmitMSDULifetime = 512,
dot11MaxReceiveLifetime = 512,
dot11ManufacturerID = 'capwap',
dot11ProductID = 'capwap',
dot11CAPLimit = 2,
dot11HCCWmin = 0,
dot11HCCWmax = 0,
dot11HCCAIFSN = 1,
dot11ADDBAResponseTimeout = 1,
dot11ADDTSResponseTimeout = 1,
dot11ChannelUtilizationBeaconInterval = 50,
dot11ScheduleTimeout = 10,
dot11DLSResponseTimeout = 10,
dot11QAPMissingAckRetryLimit = 1,
dot11EDCAAveragingPeriod = 5
}
4) Get the current configuration status report from the WTP to the
AC.
According to [RFC5415], before a WTP that has joined the AC gets
configuration from the AC, it needs to report its current
configuration status by sending a configuration status request
message to the AC, which uses the message to update MIB objects on
the AC. For example, for IEEE 802.11 binding, the AC updates data
in the ifTable [RFC2863] and IEEE 802.11 MIB module, and so on,
according to the message. For ifIndex 10, its ifOperStatus in
ifTable is updated according to the current radio operational
status in the CAPWAP message.
Shi, et al. Informational [Page 13]
RFC 5833 CAPWAP Protocol Base MIB May 2010
5) Query WTP and radio statistical data.
After WTPs start to run, the operator could query WTP and radio
statistical data through CAPWAP-BASE-MIB and the specific binding
MIB module on the AC. For example, through dot11CountersTable in
the IEEE 802.11 MIB module, the operator could query the counter
data of a radio using the ifIndex of the corresponding WTP Virtual
Radio Interface. With the capwapBaseWtpTable table in the CAPWAP-
BASE-MIB module, the operator could query the properties of
running WTPs.
6) Run MIB operations through a CAPWAP protocol wireless binding MIB
module.
For example, for the CAPWAP IEEE 802.11 binding protocol
[RFC5416], some MIB operations such as MAC mode configuration for
a WLAN depend on the CAPWAP Protocol Binding MIB for IEEE 802.11
[RFC5834]. For more information, refer to [RFC5834].
7) Query other properties of a WTP.
The Operator could query MIB objects in the ENTITY-MIB [RFC4133]
module by using the capwapBaseWtpPhyIndex in the
capwapBaseWtpTable of CAPWAP-BASE-MIB module. The properties of a
WTP such as software version, hardware version are available in
the ENTITY-MIB module.
9. Definitions
CAPWAP-BASE-MIB DEFINITIONS ::= BEGIN
IMPORTS
PhysAddress, TEXTUAL-CONVENTION, TruthValue,
DateAndTime, RowStatus
FROM SNMPv2-TC
LongUtf8String
FROM SYSAPPL-MIB
InterfaceIndex, ifGeneralInformationGroup
FROM IF-MIB
PhysicalIndex
FROM ENTITY-MIB
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
NOTIFICATION-GROUP, OBJECT-GROUP, MODULE-COMPLIANCE
FROM SNMPv2-CONF
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, mib-2,
Integer32, Unsigned32, Counter32, Gauge32, TimeTicks
Shi, et al. Informational [Page 14]
RFC 5833 CAPWAP Protocol Base MIB May 2010
FROM SNMPv2-SMI
InetAddressType, InetAddress
FROM INET-ADDRESS-MIB;
capwapBaseMIB MODULE-IDENTITY
LAST-UPDATED "201004300000Z" -- 30 April 2010
ORGANIZATION "IETF Control And Provisioning of Wireless Access
Points (CAPWAP) Working Group
http://www.ietf.org/html.charters/capwap-charter.html"
CONTACT-INFO
"General Discussion: capwap@frascone.com
To Subscribe: http://lists.frascone.com/mailman/listinfo/capwap
Yang Shi (editor)
Hangzhou H3C Tech. Co., Ltd.
Beijing R&D Center of H3C, Digital Technology Plaza
NO. 9 Shangdi 9th Street, Haidian District
Beijing 100085
China
Phone: +86 010 82775276
Email: rishyang@gmail.com
David T. Perkins (editor)
228 Bayview Dr.
San Carlos, CA 94070
USA
Phone: +1 408 394-8702
Email: dperkins@dsperkins.com
Chris Elliott (editor)
1516 Kent St.
Durham, NC 27707
USA
Phone: +1 919-308-1216
Email: chelliot@pobox.com
Yong Zhang (editor)
Fortinet, Inc.
1090 Kifer Road
Sunnyvale, CA 94086
USA
Email: yzhang@fortinet.com"
DESCRIPTION
"Copyright (c) 2010 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Shi, et al. Informational [Page 15]
RFC 5833 CAPWAP Protocol Base MIB May 2010
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
This version of this MIB module is part of RFC 5833;
see the RFC itself for full legal notices.
This MIB module contains managed object definitions for
the CAPWAP Protocol."
REVISION "201004300000Z"
DESCRIPTION
"Initial version published as RFC 5833"
::= { mib-2 196 }
-- Textual Conventions
CapwapBaseWtpProfileIdTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"Represents the unique identifier of a WTP profile."
SYNTAX Unsigned32 (0..4096)
CapwapBaseWtpIdTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "1x:"
STATUS current
DESCRIPTION
"Represents the unique identifier of a WTP instance.
As usual, the Base MAC address of the WTP is used."
SYNTAX OCTET STRING (SIZE(6|8))
CapwapBaseStationIdTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "1x:"
STATUS current
DESCRIPTION
"Represents the unique identifier of a station instance.
As usual, the MAC address of the station is used."
SYNTAX OCTET STRING (SIZE(6|8))
CapwapBaseRadioIdTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"Represents the unique identifier of a radio on a WTP."
SYNTAX Unsigned32 (1..31)
Shi, et al. Informational [Page 16]
RFC 5833 CAPWAP Protocol Base MIB May 2010
CapwapBaseTunnelModeTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Represents the tunneling modes of operation that are
supported by a WTP.
The WTP MAY support more than one option, represented by
the bit field below:
localBridging(0) - Local bridging mode
dot3Tunnel(1) - 802.3 frame tunnel mode
nativeTunnel(2) - Native frame tunnel mode"
REFERENCE
"Section 4.6.43 of CAPWAP Protocol Specification, RFC 5415."
SYNTAX BITS {
localBridging(0),
dot3Tunnel(1),
nativeTunnel(2)
}
CapwapBaseMacTypeTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Represents the MAC mode of operation supported by a WTP.
The following enumerated values are supported:
localMAC(0) - Local-MAC mode
splitMAC(1) - Split-MAC mode
both(2) - Both Local-MAC and Split-MAC
Note that the CAPWAP field [RFC5415] modeled by this
object takes zero as starting value; this MIB object
follows that rule."
REFERENCE
"Section 4.6.44 of CAPWAP Protocol Specification, RFC 5415."
SYNTAX INTEGER {
localMAC(0),
splitMAC(1),
both(2)
}
CapwapBaseChannelTypeTC::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Represents the channel type for CAPWAP protocol.
The following enumerated values are supported:
data(1) - Data channel
control(2) - Control channel"
SYNTAX INTEGER {
data(1),
control(2)
}
Shi, et al. Informational [Page 17]
RFC 5833 CAPWAP Protocol Base MIB May 2010
CapwapBaseAuthenMethodTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Represents the authentication credential type for a WTP.
The following enumerated values are supported:
other(1) - Other method, for example, vendor specific
clear(2) - Clear text and no authentication
x509(3) - X.509 certificate authentication
psk(4) - Pre-Shared secret authentication
As a mandatory requirement, CAPWAP control channel
authentication SHOULD use DTLS, either by certificate or
PSK. For data channel authentication, DTLS is optional."
SYNTAX INTEGER {
other(1),
clear(2),
x509(3),
psk(4)
}
-- Top-level components of this MIB module
-- Notifications
capwapBaseNotifications OBJECT IDENTIFIER
::= { capwapBaseMIB 0 }
-- Tables, Scalars
capwapBaseObjects OBJECT IDENTIFIER
::= { capwapBaseMIB 1 }
-- Conformance
capwapBaseConformance OBJECT IDENTIFIER
::= { capwapBaseMIB 2 }
-- AC Objects Group
capwapBaseAc OBJECT IDENTIFIER
::= { capwapBaseObjects 1 }
capwapBaseWtpSessions OBJECT-TYPE
SYNTAX Gauge32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the total number of WTPs that are connecting to
the AC."
REFERENCE
"Section 4.6.1 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseAc 1 }
Shi, et al. Informational [Page 18]
RFC 5833 CAPWAP Protocol Base MIB May 2010
capwapBaseWtpSessionsLimit OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents the maximum number of WTP sessions configured on
the AC.
The value of the object is persistent at restart/reboot."
REFERENCE
"Section 4.6.1 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseAc 2 }
capwapBaseStationSessions OBJECT-TYPE
SYNTAX Gauge32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the total number of stations that are accessing
the wireless service provided by the AC."
REFERENCE
"Section 4.6.1 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseAc 3 }
capwapBaseStationSessionsLimit OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents the maximum number of station sessions configured
on the AC.
The value of the object is persistent at restart/reboot."
REFERENCE
"Section 4.6.1 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseAc 4 }
capwapBaseDataChannelDTLSPolicyOptions OBJECT-TYPE
SYNTAX BITS {
other(0),
clear(1),
dtls(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The AC communicates its policy on the use of DTLS for
the CAPWAP data channel.
The AC MAY support more than one option, represented by the bit
field below:
Shi, et al. Informational [Page 19]
RFC 5833 CAPWAP Protocol Base MIB May 2010
other(0) - Other method, for example, vendor specific
clear(1) - Clear text
dtls(2) - DTLS"
REFERENCE
"Section 4.6.1 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseAc 5 }
capwapBaseControlChannelAuthenOptions OBJECT-TYPE
SYNTAX BITS {
x509(0),
psk(1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the authentication credential type supported by the
AC for CAPWAP control channel.
The AC MAY support more than one option, represented by the bit
field below:
x509(0) - X.509 certificate based
psk(1) - Pre-Shared secret"
REFERENCE
"Section 4.6.1 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseAc 6 }
-- capwapBaseAcNameListTable table
capwapBaseAcNameListTable OBJECT-TYPE
SYNTAX SEQUENCE OF CapwapBaseAcNameListEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of objects that configure the AC name list.
Values of all read-create objects in this table are
persistent at restart/reboot."
REFERENCE
"Section 4.6.5 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseAc 9 }
capwapBaseAcNameListEntry OBJECT-TYPE
SYNTAX CapwapBaseAcNameListEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of objects that configures the AC name list."
INDEX { capwapBaseAcNameListId }
::= { capwapBaseAcNameListTable 1 }
Shi, et al. Informational [Page 20]
RFC 5833 CAPWAP Protocol Base MIB May 2010
CapwapBaseAcNameListEntry ::= SEQUENCE {
capwapBaseAcNameListId Unsigned32,
capwapBaseAcNameListName LongUtf8String,
capwapBaseAcNameListPriority Unsigned32,
capwapBaseAcNameListRowStatus RowStatus
}
capwapBaseAcNameListId OBJECT-TYPE
SYNTAX Unsigned32 (1..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Represents the unique identifier of an AC Name list."
::= { capwapBaseAcNameListEntry 1 }
capwapBaseAcNameListName OBJECT-TYPE
SYNTAX LongUtf8String (SIZE(1..512))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Represents the name of an AC, and it is expected to be
an UTF-8 encoded string."
REFERENCE
"Section 4.6.5 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseAcNameListEntry 2 }
capwapBaseAcNameListPriority OBJECT-TYPE
SYNTAX Unsigned32 (1..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Represents the priority order of the preferred AC.
For instance, the value of one (1) is used to set the primary
AC, the value of two (2) is used to set the secondary AC, etc."
REFERENCE
"Section 4.6.5 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseAcNameListEntry 3 }
capwapBaseAcNameListRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create, modify, and/or delete a row
in this table.
The value of capwapBaseAcNameListName and
capwapBaseAcNameListPriority can be changed when this
object is in state 'active' or in 'notInService'.
Shi, et al. Informational [Page 21]
RFC 5833 CAPWAP Protocol Base MIB May 2010
The capwapBaseAcNameListRowStatus may be changed to 'active'
if all the managed objects in the conceptual row with
MAX-ACCESS read-create have been assigned valid values."
::= { capwapBaseAcNameListEntry 4 }
-- End of capwapBaseAcNameListTable table
-- capwapBaseMacAclTable table
capwapBaseMacAclTable OBJECT-TYPE
SYNTAX SEQUENCE OF CapwapBaseMacAclEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of objects that configure station Access Control
Lists (ACLs).
The WTP will not provide service to the MAC addresses
configured in this table.
Values of all read-create objects in this table are persistent
at AC restart/reboot."
REFERENCE
"Section 4.6.7 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseAc 10 }
capwapBaseMacAclEntry OBJECT-TYPE
SYNTAX CapwapBaseMacAclEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of objects that configures station Access Control
Lists (ACLs)."
INDEX { capwapBaseMacAclId }
::= { capwapBaseMacAclTable 1 }
CapwapBaseMacAclEntry ::= SEQUENCE {
capwapBaseMacAclId Unsigned32,
capwapBaseMacAclStationId CapwapBaseStationIdTC,
capwapBaseMacAclRowStatus RowStatus
}
capwapBaseMacAclId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Represents the unique identifier of an ACL."
::= { capwapBaseMacAclEntry 1 }
Shi, et al. Informational [Page 22]
RFC 5833 CAPWAP Protocol Base MIB May 2010
capwapBaseMacAclStationId OBJECT-TYPE
SYNTAX CapwapBaseStationIdTC
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Represents the MAC address of a station to which WTPs will
no longer provides service."
REFERENCE
"Section 4.6.7 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseMacAclEntry 2 }
capwapBaseMacAclRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create, modify, and/or delete a row
in this table.
The value of capwapBaseMacAclStationId can be changed when
this object is in state 'active' or in 'notInService'.
The capwapBaseMacAclRowStatus may be changed to 'active'
if all the managed objects in the conceptual row with
MAX-ACCESS read-create have been assigned valid values."
::= { capwapBaseMacAclEntry 3 }
-- End of capwapBaseMacAclTable table
-- End of AC Objects Group
-- WTP Objects Group
capwapBaseWtps OBJECT IDENTIFIER
::= { capwapBaseObjects 2 }
-- capwapBaseWtpProfileTable Table
capwapBaseWtpProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF CapwapBaseWtpProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of objects that configure WTP profiles for WTPs to
be managed before they connect to the AC.
An operator could change a WTP's configuration by changing
the values of parameters in the corresponding WTP profile,
then the WTP could get the new configuration through the
CAPWAP control channel.
Shi, et al. Informational [Page 23]
RFC 5833 CAPWAP Protocol Base MIB May 2010
Values of all read-create objects in this table are
persistent at restart/reboot."
::= { capwapBaseWtps 1 }
capwapBaseWtpProfileEntry OBJECT-TYPE
SYNTAX CapwapBaseWtpProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of objects that configures and displays a WTP profile."
INDEX { capwapBaseWtpProfileId }
::= { capwapBaseWtpProfileTable 1 }
CapwapBaseWtpProfileEntry ::= SEQUENCE {
capwapBaseWtpProfileId CapwapBaseWtpProfileIdTC,
capwapBaseWtpProfileName SnmpAdminString,
capwapBaseWtpProfileWtpMacAddress CapwapBaseWtpIdTC,
capwapBaseWtpProfileWtpModelNumber SnmpAdminString,
capwapBaseWtpProfileWtpName LongUtf8String,
capwapBaseWtpProfileWtpLocation LongUtf8String,
capwapBaseWtpProfileWtpStaticIpEnable TruthValue,
capwapBaseWtpProfileWtpStaticIpType InetAddressType,
capwapBaseWtpProfileWtpStaticIpAddress InetAddress,
capwapBaseWtpProfileWtpNetmask InetAddress,
capwapBaseWtpProfileWtpGateway InetAddress,
capwapBaseWtpProfileWtpFallbackEnable INTEGER,
capwapBaseWtpProfileWtpEchoInterval Unsigned32,
capwapBaseWtpProfileWtpIdleTimeout Unsigned32,
capwapBaseWtpProfileWtpMaxDiscoveryInterval Unsigned32,
capwapBaseWtpProfileWtpReportInterval Unsigned32,
capwapBaseWtpProfileWtpStatisticsTimer Unsigned32,
capwapBaseWtpProfileWtpEcnSupport INTEGER,
capwapBaseWtpProfileRowStatus RowStatus
}
capwapBaseWtpProfileId OBJECT-TYPE
SYNTAX CapwapBaseWtpProfileIdTC
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Represents the unique identifier of a WTP profile."
::= { capwapBaseWtpProfileEntry 1 }
capwapBaseWtpProfileName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Shi, et al. Informational [Page 24]
RFC 5833 CAPWAP Protocol Base MIB May 2010
"Represents the name of a WTP profile."
::= { capwapBaseWtpProfileEntry 2 }
capwapBaseWtpProfileWtpMacAddress OBJECT-TYPE
SYNTAX CapwapBaseWtpIdTC
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Represents the Base MAC address of a WTP.
A WTP profile MUST contain the Base MAC address of the WTP
because the CAPWAP message received from the WTP contains
its Base MAC address and the AC uses the Base MAC address to
find the corresponding WTP profile.
Section 4.6.40 of [RFC5415] omits indicating that the WTP's
Base MAC address must be included in the WTP Board Data
message element. This is a known errata item and should be
fixed in any future revision of the RFC 5415."
REFERENCE
"Section 4.6.40 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpProfileEntry 3 }
capwapBaseWtpProfileWtpModelNumber OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Represents the model number of a WTP.
A WTP profile MUST include the WTP's model number, which
reflects the number of Physical Layer (PHY) radios on the WTP.
In this way, the creation of a WTP profile triggers the AC
to automatically create the same number of WTP Virtual Radio
Interfaces corresponding to the WTP's PHY radios without
manual intervention. With the ifIndexes of WTP Virtual
Radio Interfaces, the operator could configure and manage
the WTP's PHY radios through the wireless binding MIB
modules."
REFERENCE
"Section 4.6.40 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpProfileEntry 4 }
capwapBaseWtpProfileWtpName OBJECT-TYPE
SYNTAX LongUtf8String (SIZE(1..512))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Represents the name of the WTP."
REFERENCE
"Section 4.6.45 of CAPWAP Protocol Specification, RFC 5415."
Shi, et al. Informational [Page 25]
RFC 5833 CAPWAP Protocol Base MIB May 2010
::= { capwapBaseWtpProfileEntry 5 }
capwapBaseWtpProfileWtpLocation OBJECT-TYPE
SYNTAX LongUtf8String (SIZE(1..1024))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Represents the location of the WTP."
REFERENCE
"Section 4.6.30 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpProfileEntry 6 }
capwapBaseWtpProfileWtpStaticIpEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Represents whether the WTP SHOULD use a static IP address
or not. A value of false disables the static IP address,
while a value of true enables it."
REFERENCE
"Section 4.6.48 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpProfileEntry 7 }
capwapBaseWtpProfileWtpStaticIpType OBJECT-TYPE
SYNTAX InetAddressType {ipv4(1)}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Represents the static IP address type used by the WTP.
Only ipv4(1) is supported by the object.
Although the CAPWAP protocol [RFC5415] supports both IPv4
and IPv6, note that the CAPWAP field modeled by this
object does not support IPv6, so the object does not
support ipv6(2)."
REFERENCE
"Section 4.6.48 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpProfileEntry 8 }
capwapBaseWtpProfileWtpStaticIpAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE(4))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"When capwapBaseWtpProfileWtpStaticIpEnable is true,
it represents the static IP address to be assigned to the WTP.
The format of this IP address is determined by the
corresponding instance of object
Shi, et al. Informational [Page 26]
RFC 5833 CAPWAP Protocol Base MIB May 2010
capwapBaseWtpProfileWtpStaticIpType."
REFERENCE
"Section 4.6.48 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpProfileEntry 9 }
capwapBaseWtpProfileWtpNetmask OBJECT-TYPE
SYNTAX InetAddress (SIZE(4))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"When capwapBaseWtpProfileWtpStaticIpEnable is true,
it represents the netmask to be assigned to the WTP.
The format of this netmask is determined by the
corresponding instance of object
capwapBaseWtpProfileWtpStaticIpType."
REFERENCE
"Section 4.6.48 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpProfileEntry 10 }
capwapBaseWtpProfileWtpGateway OBJECT-TYPE
SYNTAX InetAddress (SIZE(4))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"When capwapBaseWtpProfileWtpStaticIpEnable is true,
it represents the gateway to be assigned to the WTP.
The format of this IP address is determined by the
corresponding instance of object
capwapBaseWtpProfileWtpStaticIpType."
REFERENCE
"Section 4.6.48 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpProfileEntry 11 }
capwapBaseWtpProfileWtpFallbackEnable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Represents whether to enable or disable automatic CAPWAP
fallback in the event that a WTP detects its preferred AC
and is not currently connected to it.
The following enumerated values are supported:
enabled(1) - The fallback mode is enabled
disabled(2) - The fallback mode is disabled"
REFERENCE
Shi, et al. Informational [Page 27]
RFC 5833 CAPWAP Protocol Base MIB May 2010
"Section 4.6.42 of CAPWAP Protocol Specification, RFC 5415."
DEFVAL { enabled }
::= { capwapBaseWtpProfileEntry 12 }
capwapBaseWtpProfileWtpEchoInterval OBJECT-TYPE
SYNTAX Unsigned32
UNITS "second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Represents the minimum time, in seconds, between sending Echo
Request messages to the AC that the WTP has joined."
REFERENCE
"Section 4.7.7 of CAPWAP Protocol Specification, RFC 5415."
DEFVAL { 30 }
::= { capwapBaseWtpProfileEntry 13 }
capwapBaseWtpProfileWtpIdleTimeout OBJECT-TYPE
SYNTAX Unsigned32
UNITS "second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Represents the idle timeout value that the WTP SHOULD enforce
for its active stations."
REFERENCE
"Section 4.7.8 of CAPWAP Protocol Specification, RFC 5415."
DEFVAL { 300 }
::= { capwapBaseWtpProfileEntry 14 }
capwapBaseWtpProfileWtpMaxDiscoveryInterval OBJECT-TYPE
SYNTAX Unsigned32 (2..180)
UNITS "second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Represents the maximum time allowed between sending Discovery
Request messages, in seconds."
REFERENCE
"Section 4.7.10 of CAPWAP Protocol Specification, RFC 5415."
DEFVAL { 20 }
::= { capwapBaseWtpProfileEntry 15 }
capwapBaseWtpProfileWtpReportInterval OBJECT-TYPE
SYNTAX Unsigned32
UNITS "second"
MAX-ACCESS read-create
STATUS current
Shi, et al. Informational [Page 28]
RFC 5833 CAPWAP Protocol Base MIB May 2010
DESCRIPTION
"Represents the interval for WTP to send the Decryption Error
report."
REFERENCE
"Section 4.7.11 of CAPWAP Protocol Specification, RFC 5415."
DEFVAL { 120 }
::= { capwapBaseWtpProfileEntry 16 }
capwapBaseWtpProfileWtpStatisticsTimer OBJECT-TYPE
SYNTAX Unsigned32
UNITS "second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Represents the interval the WTP uses between the WTP Event
Requests it transmits to the AC to communicate its statistics,
in seconds."
REFERENCE
"Section 4.7.14 of CAPWAP Protocol Specification, RFC 5415."
DEFVAL { 120 }
::= { capwapBaseWtpProfileEntry 17 }
capwapBaseWtpProfileWtpEcnSupport OBJECT-TYPE
SYNTAX INTEGER {
limited(0),
fullAndLimited(1)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Represents the support for the Explicit Congestion Notification
(ECN) bits, as defined in [RFC3168].
The following enumerated values are supported:
limited(0) - Limited ECN support
fullAndLimited(1) - Full and limited ECN support
Note that the CAPWAP field [RFC5415] modeled by this
object takes zero as starting value; this MIB object follows
that rule."
REFERENCE
"Section 4.6.25 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpProfileEntry 18 }
capwapBaseWtpProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create, modify, and/or delete a row
Shi, et al. Informational [Page 29]
RFC 5833 CAPWAP Protocol Base MIB May 2010
in this table.
The value of capwapBaseWtpProfileName,
capwapBaseWtpProfileWtpName and capwapBaseWtpProfileWtpLocation
can be changed when this object is in state 'active' or in
'notInService'.
The other objects in a row can be modified only when the value
of this object in the corresponding conceptual row is not
'active'. Thus, to modify one or more of the objects in
this conceptual row:
a. change the row status to 'notInService'
b. change the values of the row
c. change the row status to 'active'
The capwapBaseWtpProfileRowStatus may be changed to 'active'
if the managed objects capwapBaseWtpProfileName,
capwapBaseWtpProfileWtpMacAddress,
capwapBaseWtpProfileWtpModelNumber,
capwapBaseWtpProfileWtpName, and
capwapBaseWtpProfileWtpLocation in the conceptual row
have been assigned valid values.
Deleting a WTP profile in use will disconnect the WTP from
the AC. So the network management system SHOULD
ask the operator to confirm such an operation.
When a WTP profile entry is removed from the table,
the corresponding WTP Virtual Radio Interfaces are also
removed from the capwapBaseWirelessBindingTable and
ifTable [RFC2863].
Also, the related object instances SHOULD be removed from
the wireless binding MIB modules such as the IEEE 802.11
MIB module [IEEE.802-11.2007]."
::= { capwapBaseWtpProfileEntry 19 }
-- End of capwapBaseWtpProfileTable table
-- capwapBaseWtpStateTable table
capwapBaseWtpStateTable OBJECT-TYPE
SYNTAX SEQUENCE OF CapwapBaseWtpStateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of objects that indicate the AC's CAPWAP FSM state
for each WTP, and helps the operator to query a WTP's
current configuration."
::= { capwapBaseWtps 2 }
capwapBaseWtpStateEntry OBJECT-TYPE
Shi, et al. Informational [Page 30]
RFC 5833 CAPWAP Protocol Base MIB May 2010
SYNTAX CapwapBaseWtpStateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of objects that displays the AC's CAPWAP FSM state
for each WTP.
Also, the operator could query the current configuration
of a WTP by using the identifier of the corresponding
WTP profile."
INDEX { capwapBaseWtpStateWtpId }
::= { capwapBaseWtpStateTable 1 }
CapwapBaseWtpStateEntry ::= SEQUENCE {
capwapBaseWtpStateWtpId CapwapBaseWtpIdTC,
capwapBaseWtpStateWtpIpAddressType InetAddressType,
capwapBaseWtpStateWtpIpAddress InetAddress,
capwapBaseWtpStateWtpLocalIpAddressType InetAddressType,
capwapBaseWtpStateWtpLocalIpAddress InetAddress,
capwapBaseWtpStateWtpBaseMacAddress PhysAddress,
capwapBaseWtpState INTEGER,
capwapBaseWtpStateWtpUpTime TimeTicks,
capwapBaseWtpStateWtpCurrWtpProfileId CapwapBaseWtpProfileIdTC
}
capwapBaseWtpStateWtpId OBJECT-TYPE
SYNTAX CapwapBaseWtpIdTC
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Represents the unique identifier of a WTP."
::= { capwapBaseWtpStateEntry 1 }
capwapBaseWtpStateWtpIpAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the IP address type of a WTP.
Only ipv4(1) and ipv6(2) are supported by the object."
::= { capwapBaseWtpStateEntry 2 }
capwapBaseWtpStateWtpIpAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the IP address of a WTP that corresponds to
the IP address in the IP packet header.
Shi, et al. Informational [Page 31]
RFC 5833 CAPWAP Protocol Base MIB May 2010
The format of this IP address is determined by
the corresponding instance of object
capwapBaseWtpStateWtpIpAddressType."
REFERENCE
"Section 4 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpStateEntry 3 }
capwapBaseWtpStateWtpLocalIpAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the local IP address type of a WTP.
Only ipv4(1) and ipv6(2) are supported by the object."
::= { capwapBaseWtpStateEntry 4 }
capwapBaseWtpStateWtpLocalIpAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the local IP address of a WTP and models the
CAPWAP Local IPv4 Address or CAPWAP Local IPv6 Address fields
[RFC5415].
If a Network Address Translation (NAT) device is present
between WTP and AC, the value of
capwapBaseWtpStateWtpLocalIpAddress will be different from the
value of capwapBaseWtpStateWtpIpAddress.
The format of this IP address is determined by
the corresponding instance of object
capwapBaseWtpStateWtpLocalIpAddressType."
REFERENCE
"Sections 4.6.11 and 4.6.12 of CAPWAP Protocol Specification,
RFC 5415."
::= { capwapBaseWtpStateEntry 5 }
capwapBaseWtpStateWtpBaseMacAddress OBJECT-TYPE
SYNTAX PhysAddress (SIZE(6|8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the WTP's Base MAC Address, which MAY be
assigned to the primary Ethernet interface.
The instance of the object corresponds to the Base MAC Address
sub-element in the CAPWAP protocol [RFC5415]."
REFERENCE
"Section 4.6.40 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpStateEntry 6 }
Shi, et al. Informational [Page 32]
RFC 5833 CAPWAP Protocol Base MIB May 2010
capwapBaseWtpState OBJECT-TYPE
SYNTAX INTEGER {
dtls(1),
join(2),
image(3),
configure(4),
dataCheck(5),
run(6),
reset(7),
dtlsTeardown(8),
unknown(9)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the various possibilities of the AC's CAPWAP FSM
state for each WTP.
The following enumerated values are supported:
dtls(1) - DTLS negotiation states, which include
DTLS setup, authorize, DTLS connect
join(2) - The WTP is joining with the AC
image(3) - The WTP is downloading software
configure(4) - The WTP is getting configuration from
the AC
dataCheck(5) - The AC is waiting for the Data Channel Keep
Alive Packet
run(6) - The WTP enters the running state
reset(7) - The AC transmits a reset request message
to the WTP
dtlsTeardown(8) - DTLS session is torn down
unknown(9) - Operator already prepared configuration
for the WTP, while the WTP has not
contacted the AC until now"
REFERENCE
"Section 2.3.1 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpStateEntry 7 }
capwapBaseWtpStateWtpUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the time (in hundredths of a second) since the
WTP has been in the running state (corresponding to the
value run(6) of capwapBaseWtpState)."
::= { capwapBaseWtpStateEntry 8 }
capwapBaseWtpStateWtpCurrWtpProfileId OBJECT-TYPE
Shi, et al. Informational [Page 33]
RFC 5833 CAPWAP Protocol Base MIB May 2010
SYNTAX CapwapBaseWtpProfileIdTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the current identifier of a WTP profile.
The operator could query a WTP's current configuration
with the identifier of a WTP profile."
::= { capwapBaseWtpStateEntry 9 }
-- End of capwapBaseWtpStateTable Table
-- capwapBaseWtpTable Table
capwapBaseWtpTable OBJECT-TYPE
SYNTAX SEQUENCE OF CapwapBaseWtpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of objects that display properties of the WTPs
in running state."
::= { capwapBaseWtps 3 }
capwapBaseWtpEntry OBJECT-TYPE
SYNTAX CapwapBaseWtpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of objects that displays properties of the WTPs
in running state."
INDEX { capwapBaseWtpCurrId }
::= { capwapBaseWtpTable 1 }
CapwapBaseWtpEntry ::= SEQUENCE {
capwapBaseWtpCurrId CapwapBaseWtpIdTC,
capwapBaseWtpPhyIndex PhysicalIndex,
capwapBaseWtpBaseMacAddress PhysAddress,
capwapBaseWtpTunnelModeOptions CapwapBaseTunnelModeTC,
capwapBaseWtpMacTypeOptions CapwapBaseMacTypeTC,
capwapBaseWtpDiscoveryType INTEGER,
capwapBaseWtpRadiosInUseNum Gauge32,
capwapBaseWtpRadioNumLimit Unsigned32,
capwapBaseWtpRetransmitCount Counter32
}
capwapBaseWtpCurrId OBJECT-TYPE
SYNTAX CapwapBaseWtpIdTC
MAX-ACCESS not-accessible
Shi, et al. Informational [Page 34]
RFC 5833 CAPWAP Protocol Base MIB May 2010
STATUS current
DESCRIPTION
"Represents the unique identifier of a WTP in running state."
::= { capwapBaseWtpEntry 1 }
capwapBaseWtpPhyIndex OBJECT-TYPE
SYNTAX PhysicalIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the unique physical index of a physical entity
in the ENTITY-MIB module [RFC4133].
Information about a specific WTP such as its software version
could be accessed through this index."
::= { capwapBaseWtpEntry 2 }
capwapBaseWtpBaseMacAddress OBJECT-TYPE
SYNTAX PhysAddress (SIZE(6|8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the WTP's Base MAC Address, which MAY be assigned
to the primary Ethernet interface.
The instance of the object corresponds to the Base MAC Address
sub-element in the CAPWAP protocol [RFC5415]."
REFERENCE
"Section 4.6.40 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpEntry 3 }
capwapBaseWtpTunnelModeOptions OBJECT-TYPE
SYNTAX CapwapBaseTunnelModeTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the tunneling modes of operation supported by
the WTP."
REFERENCE
"Section 4.6.43 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpEntry 4 }
capwapBaseWtpMacTypeOptions OBJECT-TYPE
SYNTAX CapwapBaseMacTypeTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the MAC mode of operation supported by the WTP."
REFERENCE
"Section 4.6.44 of CAPWAP Protocol Specification, RFC 5415."
Shi, et al. Informational [Page 35]
RFC 5833 CAPWAP Protocol Base MIB May 2010
::= { capwapBaseWtpEntry 5 }
capwapBaseWtpDiscoveryType OBJECT-TYPE
SYNTAX INTEGER {
unknown(0),
staticConfig(1),
dhcp(2),
dns(3),
acRef(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents how the WTP discovers the AC.
The following enumerated values are supported:
unknown(0) - Unknown
staticConfig(1) - Static configuration
dhcp(2) - DHCP
dns(3) - DNS
acRef(4) - AC referral
Note that the CAPWAP field [RFC5415] modeled by this
object takes zero as starting value; this MIB object
follows that rule."
REFERENCE
"Section 4.6.21 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpEntry 6 }
capwapBaseWtpRadiosInUseNum OBJECT-TYPE
SYNTAX Gauge32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of radios in use on the WTP."
REFERENCE
"Section 4.6.41 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpEntry 7 }
capwapBaseWtpRadioNumLimit OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the maximum radio number supported by the WTP."
REFERENCE
"Section 4.6.41 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpEntry 8 }
capwapBaseWtpRetransmitCount OBJECT-TYPE
Shi, et al. Informational [Page 36]
RFC 5833 CAPWAP Protocol Base MIB May 2010
SYNTAX Counter32
UNITS "retransmissions"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of retransmissions for a given
CAPWAP packet."
REFERENCE
"Section 4.8.8 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpEntry 9 }
-- End of capwapBaseWtpTable table
-- capwapBaseWirelessBindingTable Table
capwapBaseWirelessBindingTable OBJECT-TYPE
SYNTAX SEQUENCE OF CapwapBaseWirelessBindingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of objects that display the mappings between
WTP Virtual Radio Interfaces and PHY radios, and the
wireless binding type for each PHY radio.
As capwapBaseWirelessBindingTable stores the mappings between
PHY radios (Radio IDs) and the ifIndexes of WTP Virtual Radio
Interfaces, the operator can get the ifIndex information by
querying this table. Such a query operation SHOULD run from
radio ID 1 to radio ID 31 according to [RFC5415],
and stop when an invalid ifIndex value (0) is returned.
Values of all objects in this table are persistent at
restart/reboot."
::= { capwapBaseWtps 4 }
capwapBaseWirelessBindingEntry OBJECT-TYPE
SYNTAX CapwapBaseWirelessBindingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of objects that displays the mapping between
a specific WTP Virtual Radio Interface and a PHY
radio, and the wireless binding type for the PHY radio."
INDEX {
capwapBaseWtpProfileId,
capwapBaseWirelessBindingRadioId
}
::= { capwapBaseWirelessBindingTable 1 }
Shi, et al. Informational [Page 37]
RFC 5833 CAPWAP Protocol Base MIB May 2010
CapwapBaseWirelessBindingEntry ::= SEQUENCE {
capwapBaseWirelessBindingRadioId CapwapBaseRadioIdTC,
capwapBaseWirelessBindingVirtualRadioIfIndex InterfaceIndex,
capwapBaseWirelessBindingType INTEGER
}
capwapBaseWirelessBindingRadioId OBJECT-TYPE
SYNTAX CapwapBaseRadioIdTC
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Represents the identifier of a PHY radio on a WTP, which
is required to be unique on a WTP.
For example, WTP A and WTP B use a same value of
capwapBaseWirelessBindingRadioId for their first radio."
REFERENCE
"Section 4.3 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWirelessBindingEntry 1 }
capwapBaseWirelessBindingVirtualRadioIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the index value that uniquely identifies a
WLAN Virtual Radio Interface. The interface identified by
a particular value of this index is the same interface as
identified by the same value of the ifIndex.
Before WTPs contact the AC to get configuration,
the operator configures WTP profiles for them.
The creation of a WTP profile triggers the system to
automatically create a specific number of WTP Virtual Radio
Interfaces and add a new row object in the
capwapBaseWirelessBindingTable without manual intervention.
As most MIB modules use the ifIndex to identify an interface
for configuration and statistical data (for example, the IEEE
802.11 MIB module [IEEE.802-11.2007]), it will be easy to
reuse other wireless binding MIB modules through the WTP
Virtual Radio Interface in the Centralized WLAN
Architecture."
::= { capwapBaseWirelessBindingEntry 2 }
capwapBaseWirelessBindingType OBJECT-TYPE
SYNTAX INTEGER {
dot11(1),
epc(3)
}
MAX-ACCESS read-only
Shi, et al. Informational [Page 38]
RFC 5833 CAPWAP Protocol Base MIB May 2010
STATUS current
DESCRIPTION
"Represents the wireless binding type for the radio.
The following enumerated values are supported:
dot11(1) - IEEE 802.11
epc(3) - EPCGlobal"
REFERENCE
"Section 4.3 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWirelessBindingEntry 3 }
-- End of capwapBaseWirelessBindingTable Table
-- capwapBaseStationTable Table
capwapBaseStationTable OBJECT-TYPE
SYNTAX SEQUENCE OF CapwapBaseStationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of objects that display stations that are accessing
the wireless service provided by the AC."
REFERENCE
"Section 4.6.8 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtps 5 }
capwapBaseStationEntry OBJECT-TYPE
SYNTAX CapwapBaseStationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of objects that displays a station that is
associated with the specific radio on the WTP.
Note that in some cases such as roaming that a station may
simultaneously associate with two WTPs for some (short) time.
The MIB implementation MUST ensure there is only one valid
and meaningful entry for a specific station."
INDEX { capwapBaseStationId }
::= { capwapBaseStationTable 1 }
CapwapBaseStationEntry ::= SEQUENCE {
capwapBaseStationId CapwapBaseStationIdTC,
capwapBaseStationWtpId CapwapBaseWtpIdTC,
capwapBaseStationWtpRadioId CapwapBaseRadioIdTC,
capwapBaseStationAddedTime DateAndTime,
capwapBaseStationVlanName SnmpAdminString
}
Shi, et al. Informational [Page 39]
RFC 5833 CAPWAP Protocol Base MIB May 2010
capwapBaseStationId OBJECT-TYPE
SYNTAX CapwapBaseStationIdTC
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Represents the unique identifier of the station."
REFERENCE
"Section 4.6.8 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseStationEntry 1 }
capwapBaseStationWtpId OBJECT-TYPE
SYNTAX CapwapBaseWtpIdTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the unique identifier of a WTP in running state."
::= { capwapBaseStationEntry 2 }
capwapBaseStationWtpRadioId OBJECT-TYPE
SYNTAX CapwapBaseRadioIdTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the identifier of a PHY radio on a WTP, which
is required to be unique on a WTP.
For example, WTP A and WTP B use a same value of
capwapBaseStationWtpRadioId for their first radio."
REFERENCE
"Section 4.3 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseStationEntry 3 }
capwapBaseStationAddedTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the time when the station is added."
REFERENCE
"Section 4.6.8 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseStationEntry 4 }
capwapBaseStationVlanName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents VLAN name to which the station is associated."
REFERENCE
Shi, et al. Informational [Page 40]
RFC 5833 CAPWAP Protocol Base MIB May 2010
"Section 4.6.8 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseStationEntry 5 }
-- End of capwapBaseStationTable Table
-- capwapBaseWtpEventsStatsTable
capwapBaseWtpEventsStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF CapwapBaseWtpEventsStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of objects that display the WTPs' events statistics."
REFERENCE
"Section 4.6.47 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtps 6 }
capwapBaseWtpEventsStatsEntry OBJECT-TYPE
SYNTAX CapwapBaseWtpEventsStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of objects that displays the events statistics
of a WTP."
REFERENCE
"Section 4.6.47 of CAPWAP Protocol Specification, RFC 5415."
INDEX { capwapBaseWtpCurrId }
::= { capwapBaseWtpEventsStatsTable 1 }
CapwapBaseWtpEventsStatsEntry ::= SEQUENCE {
capwapBaseWtpEventsStatsRebootCount Counter32,
capwapBaseWtpEventsStatsInitCount Counter32,
capwapBaseWtpEventsStatsLinkFailureCount Counter32,
capwapBaseWtpEventsStatsSwFailureCount Counter32,
capwapBaseWtpEventsStatsHwFailureCount Counter32,
capwapBaseWtpEventsStatsOtherFailureCount Counter32,
capwapBaseWtpEventsStatsUnknownFailureCount Counter32,
capwapBaseWtpEventsStatsLastFailureType INTEGER
}
capwapBaseWtpEventsStatsRebootCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of reboots that have occurred due to a
WTP crash.
Shi, et al. Informational [Page 41]
RFC 5833 CAPWAP Protocol Base MIB May 2010
Note that the CAPWAP field [RFC5415] modeled by this counter
takes the value 65535 to indicate that the information is not
available on the WTP. This MIB object does not follow this
behavior, which would not be standard in SMIv2. If the WTP
does not have the information, the agent will not instantiate
the object."
REFERENCE
"Section 4.6.47 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpEventsStatsEntry 1 }
capwapBaseWtpEventsStatsInitCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of reboots that have occurred at the
request of a CAPWAP protocol message, such as a change in
configuration that requires a reboot or an explicit CAPWAP
protocol reset request.
Note that the CAPWAP field [RFC5415] modeled by this counter
takes the value 65535 to indicate that the information is not
available on the WTP. This MIB object does not follow this
behavior, which would not be standard in SMIv2. If the WTP
does not have the information, the agent will not instantiate
the object."
REFERENCE
"Section 4.6.47 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpEventsStatsEntry 2 }
capwapBaseWtpEventsStatsLinkFailureCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of times that a CAPWAP protocol
connection with an AC has failed due to link failures."
REFERENCE
"Section 4.6.47 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpEventsStatsEntry 3 }
capwapBaseWtpEventsStatsSwFailureCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of times that a CAPWAP protocol
connection with an AC has failed due to software-related
reasons."
Shi, et al. Informational [Page 42]
RFC 5833 CAPWAP Protocol Base MIB May 2010
REFERENCE
"Section 4.6.47 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpEventsStatsEntry 4 }
capwapBaseWtpEventsStatsHwFailureCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of times that a CAPWAP protocol
connection with an AC has failed due to hardware-related
reasons."
REFERENCE
"Section 4.6.47 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpEventsStatsEntry 5 }
capwapBaseWtpEventsStatsOtherFailureCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of times that a CAPWAP protocol
connection with an AC has failed due to known reasons, other
than the AC-initiated, link, software or hardware failures."
REFERENCE
"Section 4.6.47 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpEventsStatsEntry 6 }
capwapBaseWtpEventsStatsUnknownFailureCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of times that a CAPWAP protocol
connection with an AC has failed for unknown reasons."
REFERENCE
"Section 4.6.47 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpEventsStatsEntry 7 }
capwapBaseWtpEventsStatsLastFailureType OBJECT-TYPE
SYNTAX INTEGER {
unsupported(0),
acInit(1),
linkFailure(2),
swFailure(3),
hwFailure(4),
otherFailure(5),
unknown(255)
Shi, et al. Informational [Page 43]
RFC 5833 CAPWAP Protocol Base MIB May 2010
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the failure type of the most recent WTP failure.
The following enumerated values are supported:
unsupported(0) - Not supported
acInit(1) - The AC initiated
linkFailure(2) - Link failure
swFailure(3) - Software failure
hwFailure(4) - Hardware failure
otherFailure(5) - Other failure
unknown(255) - Unknown (e.g., WTP doesn't keep track
of info)
Note that the CAPWAP field [RFC5415] modeled by this
object takes zero as starting value; this MIB object
follows that rule."
REFERENCE
"Section 4.6.47 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtpEventsStatsEntry 8 }
-- End of capwapBaseWtpEventsStatsTable table
-- capwapBaseRadioEventsStatsTable table
capwapBaseRadioEventsStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF CapwapBaseRadioEventsStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of objects that display statistics on the radios'
behaviors and reasons why the WTP radio has been reset.
To get the events statistics of all radios on a specific WTP
(identified by the capwapBaseWtpCurrId), a query
operation SHOULD run from radio ID 1 to radio ID 31 until there
is no data returned. The radio ID here corresponds to the
object capwapBaseRadioEventsWtpRadioId. If the previous MIB
operations such as query on the capwapBaseWirelessBindingTable
know the exact value of each radio ID, the query operation on
the capwapBaseRadioEventsStatsTable could use that value
of Radio IDs."
REFERENCE
"Section 4.6.46 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseWtps 7 }
capwapBaseRadioEventsStatsEntry OBJECT-TYPE
SYNTAX CapwapBaseRadioEventsStatsEntry
Shi, et al. Informational [Page 44]
RFC 5833 CAPWAP Protocol Base MIB May 2010
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of objects that displays the statistical data of
events that happened on a specific radio of a WTP."
INDEX { capwapBaseWtpCurrId, capwapBaseRadioEventsWtpRadioId }
::= { capwapBaseRadioEventsStatsTable 1 }
CapwapBaseRadioEventsStatsEntry ::= SEQUENCE {
capwapBaseRadioEventsWtpRadioId CapwapBaseRadioIdTC,
capwapBaseRadioEventsStatsResetCount Counter32,
capwapBaseRadioEventsStatsSwFailureCount Counter32,
capwapBaseRadioEventsStatsHwFailureCount Counter32,
capwapBaseRadioEventsStatsOtherFailureCount Counter32,
capwapBaseRadioEventsStatsUnknownFailureCount Counter32,
capwapBaseRadioEventsStatsConfigUpdateCount Counter32,
capwapBaseRadioEventsStatsChannelChangeCount Counter32,
capwapBaseRadioEventsStatsBandChangeCount Counter32,
capwapBaseRadioEventsStatsCurrNoiseFloor Integer32,
capwapBaseRadioEventsStatsDecryptErrorCount Counter32,
capwapBaseRadioEventsStatsLastFailureType INTEGER
}
capwapBaseRadioEventsWtpRadioId OBJECT-TYPE
SYNTAX CapwapBaseRadioIdTC
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Represents the identifier of a PHY radio on a WTP, which
is required to be unique on a WTP.
For example, WTP A and WTP B use the same value of
capwapBaseRadioEventsWtpRadioId for their first radio."
REFERENCE
"Section 4.3 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseRadioEventsStatsEntry 1 }
capwapBaseRadioEventsStatsResetCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of times that the radio has been
reset."
REFERENCE
"Section 4.6.46 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseRadioEventsStatsEntry 2 }
capwapBaseRadioEventsStatsSwFailureCount OBJECT-TYPE
Shi, et al. Informational [Page 45]
RFC 5833 CAPWAP Protocol Base MIB May 2010
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of times that the radio has failed due
to software-related reasons."
REFERENCE
"Section 4.6.46 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseRadioEventsStatsEntry 3 }
capwapBaseRadioEventsStatsHwFailureCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of times that the radio has failed due
to hardware-related reasons."
REFERENCE
"Section 4.6.46 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseRadioEventsStatsEntry 4 }
capwapBaseRadioEventsStatsOtherFailureCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of times that the radio has failed due to
known reasons, other than software or hardware failure."
REFERENCE
"Section 4.6.46 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseRadioEventsStatsEntry 5 }
capwapBaseRadioEventsStatsUnknownFailureCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of times that the radio has failed for
unknown reasons."
REFERENCE
"Section 4.6.46 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseRadioEventsStatsEntry 6 }
capwapBaseRadioEventsStatsConfigUpdateCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Shi, et al. Informational [Page 46]
RFC 5833 CAPWAP Protocol Base MIB May 2010
"Represents the number of times that the radio configuration has
been updated."
REFERENCE
"Section 4.6.46 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseRadioEventsStatsEntry 7 }
capwapBaseRadioEventsStatsChannelChangeCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of times that the radio channel has
been changed."
REFERENCE
"Section 4.6.46 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseRadioEventsStatsEntry 8 }
capwapBaseRadioEventsStatsBandChangeCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of times that the radio has changed
frequency bands."
REFERENCE
"Section 4.6.46 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseRadioEventsStatsEntry 9 }
capwapBaseRadioEventsStatsCurrNoiseFloor OBJECT-TYPE
SYNTAX Integer32
UNITS "dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the noise floor of the radio receiver in units of
dBm."
REFERENCE
"Section 4.6.46 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseRadioEventsStatsEntry 10 }
capwapBaseRadioEventsStatsDecryptErrorCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of decryption errors that have occurred
on the WTP. Note that this field is only valid in cases where
the WTP provides encryption/decryption services."
Shi, et al. Informational [Page 47]
RFC 5833 CAPWAP Protocol Base MIB May 2010
REFERENCE
"Section 4.6.46 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseRadioEventsStatsEntry 11 }
capwapBaseRadioEventsStatsLastFailureType OBJECT-TYPE
SYNTAX INTEGER {
unsupported(0),
swFailure(1),
hwFailure(2),
otherFailure(3),
unknown(255)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the failure type of the most recent radio failure.
The following enumerated values are supported:
unsupported(0) - Not supported
swFailure(1) - Software failure
hwFailure(2) - Hardware failure
otherFailure(3) - Other failure
unknown(255) - Unknown
Note that the CAPWAP field [RFC5415] modeled by this
object takes zero as starting value; this MIB object follows
that rule."
REFERENCE
"Section 4.6.46 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseRadioEventsStatsEntry 12 }
-- End of capwapBaseRadioEventsStatsTable table
-- End of WTP Objects Group
-- CAPWAP Base Parameters Group
capwapBaseParameters OBJECT IDENTIFIER
::= { capwapBaseObjects 3 }
capwapBaseAcMaxRetransmit OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents the maximum number of retransmissions for a given
CAPWAP packet before the link layer considers the peer dead.
The value of the object is persistent at restart/reboot."
REFERENCE
Shi, et al. Informational [Page 48]
RFC 5833 CAPWAP Protocol Base MIB May 2010
"Section 4.8.7 of CAPWAP Protocol Specification, RFC 5415."
DEFVAL { 5 }
::= { capwapBaseParameters 1 }
capwapBaseAcChangeStatePendingTimer OBJECT-TYPE
SYNTAX Unsigned32
UNITS "second"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents the maximum time, in seconds, the AC will wait
for the Change State Event Request from the WTP after having
transmitted a successful Configuration Status Response
message.
The value of the object is persistent at restart/reboot."
REFERENCE
"Section 4.7.1 of CAPWAP Protocol Specification, RFC 5415."
DEFVAL { 25 }
::= { capwapBaseParameters 2 }
capwapBaseAcDataCheckTimer OBJECT-TYPE
SYNTAX Unsigned32
UNITS "second"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents The number of seconds the AC will wait for
the Data Channel Keep Alive, which is required by the
CAPWAP state machine's Data Check state.
The AC resets the state machine if this timer expires
prior to transitioning to the next state.
The value of the object is persistent at restart/reboot."
REFERENCE
"Section 4.7.4 of CAPWAP Protocol Specification, RFC 5415."
DEFVAL { 30 }
::= { capwapBaseParameters 3 }
capwapBaseAcDTLSSessionDeleteTimer OBJECT-TYPE
SYNTAX Unsigned32
UNITS "second"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents the minimum time, in seconds, the AC MUST wait
for DTLS session deletion.
The value of the object is persistent at restart/reboot."
REFERENCE
"Section 4.7.6 of CAPWAP Protocol Specification, RFC 5415."
Shi, et al. Informational [Page 49]
RFC 5833 CAPWAP Protocol Base MIB May 2010
DEFVAL { 5 }
::= { capwapBaseParameters 4 }
capwapBaseAcEchoInterval OBJECT-TYPE
SYNTAX Unsigned32
UNITS "second"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents the minimum time, in seconds, between sending Echo
Request messages to the AC with which the WTP has joined.
The value of the object is persistent at restart/reboot."
REFERENCE
"Section 4.7.7 of CAPWAP Protocol Specification, RFC 5415."
DEFVAL { 30 }
::= { capwapBaseParameters 5 }
capwapBaseAcRetransmitInterval OBJECT-TYPE
SYNTAX Unsigned32
UNITS "second"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents the minimum time, in seconds, in which a
non-acknowledged CAPWAP packet will be retransmitted.
The value of the object is persistent at restart/reboot."
REFERENCE
"Section 4.7.12 of CAPWAP Protocol Specification, RFC 5415."
DEFVAL { 3 }
::= { capwapBaseParameters 6 }
capwapBaseAcSilentInterval OBJECT-TYPE
SYNTAX Unsigned32
UNITS "second"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents the minimum time, in seconds, during which the AC
SHOULD ignore all CAPWAP and DTLS packets received from the
WTP that is in the Sulking state.
The value of the object is persistent at restart/reboot."
REFERENCE
"Section 4.7.13 of CAPWAP Protocol Specification, RFC 5415."
DEFVAL { 30 }
::= { capwapBaseParameters 7 }
capwapBaseAcWaitDTLSTimer OBJECT-TYPE
SYNTAX Unsigned32 (30..4294967295)
Shi, et al. Informational [Page 50]
RFC 5833 CAPWAP Protocol Base MIB May 2010
UNITS "second"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents the maximum time, in seconds, the AC MUST wait
without having received a DTLS Handshake message from an AC.
This timer MUST be greater than 30 seconds.
The value of the object is persistent at restart/reboot."
REFERENCE
"Section 4.7.15 of CAPWAP Protocol Specification, RFC 5415."
DEFVAL { 60 }
::= { capwapBaseParameters 8 }
capwapBaseAcWaitJoinTimer OBJECT-TYPE
SYNTAX Unsigned32 (20..4294967295)
UNITS "second"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents the maximum time, in seconds, the AC will wait
after the DTLS session has been established until it receives
the Join Request from the WTP. This timer MUST be greater
than 20 seconds.
The value of the object is persistent at restart/reboot."
REFERENCE
"Section 4.7.16 of CAPWAP Protocol Specification, RFC 5415."
DEFVAL { 60 }
::= { capwapBaseParameters 9 }
capwapBaseAcEcnSupport OBJECT-TYPE
SYNTAX INTEGER {
limited(0),
fullAndLimited(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents the support for the Explicit Congestion Notification
(ECN) bits, as defined in [RFC3168].
The value of the object is persistent at restart/reboot.
The following enumerated values are supported:
limited(0) - Limited ECN support
fullAndLimited(1) - Full and limited ECN support
Note that the CAPWAP field [RFC5415] modeled by this
object takes zero as starting value; this MIB object follows
that rule."
REFERENCE
"Section 4.6.25 of CAPWAP Protocol Specification, RFC 5415."
Shi, et al. Informational [Page 51]
RFC 5833 CAPWAP Protocol Base MIB May 2010
::= { capwapBaseParameters 10 }
-- End of CAPWAP Base Parameters Group
-- CAPWAP Statistics Group
capwapBaseStats OBJECT IDENTIFIER
::= { capwapBaseObjects 4 }
capwapBaseFailedDTLSAuthFailureCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of failed DTLS session establishment
attempts due to authentication failures."
REFERENCE
"Section 4.8.3 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseStats 1 }
capwapBaseFailedDTLSSessionCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Represents the number of failed DTLS session
establishment attempts."
REFERENCE
"Section 4.8.4 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseStats 2 }
-- Notifications
capwapBaseChannelUp NOTIFICATION-TYPE
OBJECTS {
capwapBaseNtfWtpId,
capwapBaseNtfChannelType,
capwapBaseNtfAuthenMethod
}
STATUS current
DESCRIPTION
"This notification is sent by the AC when a CAPWAP channel
is established.
The notification is separated for data or control channel."
::= { capwapBaseNotifications 1 }
capwapBaseChannelDown NOTIFICATION-TYPE
Shi, et al. Informational [Page 52]
RFC 5833 CAPWAP Protocol Base MIB May 2010
OBJECTS {
capwapBaseNtfWtpId,
capwapBaseNtfChannelType,
capwapBaseNtfChannelDownReason
}
STATUS current
DESCRIPTION
"This notification is sent by the AC when a CAPWAP channel
is down.
The notification is separated for data or control channel."
::= { capwapBaseNotifications 2 }
capwapBaseDecryptErrorReport NOTIFICATION-TYPE
OBJECTS {
capwapBaseNtfWtpId,
capwapBaseNtfRadioId,
capwapBaseNtfStationIdList
}
STATUS current
DESCRIPTION
"This notification is generated when a WTP has had a
decryption error since the last report."
REFERENCE
"Section 4.6.17 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseNotifications 3 }
capwapBaseJoinFailure NOTIFICATION-TYPE
OBJECTS {
capwapBaseNtfWtpId,
capwapBaseNtfJoinFailureReason
}
STATUS current
DESCRIPTION
"This notification is generated when a WTP fails to join."
REFERENCE
"Section 4.6.35 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseNotifications 4 }
capwapBaseImageUpgradeFailure NOTIFICATION-TYPE
OBJECTS {
capwapBaseNtfWtpId,
capwapBaseNtfImageFailureReason
}
STATUS current
DESCRIPTION
"This notification is generated when a WTP fails to update
the firmware image."
REFERENCE
Shi, et al. Informational [Page 53]
RFC 5833 CAPWAP Protocol Base MIB May 2010
"Section 4.6.35 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseNotifications 5 }
capwapBaseConfigMsgError NOTIFICATION-TYPE
OBJECTS {
capwapBaseNtfWtpId,
capwapBaseNtfConfigMsgErrorType,
capwapBaseNtfMsgErrorElements
}
STATUS current
DESCRIPTION
"This notification is generated when a WTP receives message
elements in the configuration management messages that it
is unable to apply locally."
REFERENCE
"Section 4.6.35 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseNotifications 6 }
capwapBaseRadioOperableStatus NOTIFICATION-TYPE
OBJECTS {
capwapBaseNtfWtpId,
capwapBaseNtfRadioId,
capwapBaseNtfRadioOperStatusFlag,
capwapBaseNtfRadioStatusCause
}
STATUS current
DESCRIPTION
"The notification is generated when a radio's operational state
has changed."
REFERENCE
"Section 4.6.34 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseNotifications 7 }
capwapBaseAuthenFailure NOTIFICATION-TYPE
OBJECTS {
capwapBaseNtfWtpId,
capwapBaseNtfChannelType,
capwapBaseNtfAuthenMethod,
capwapBaseNtfAuthenFailureReason
}
STATUS current
DESCRIPTION
"This is notification of an authentication failure event
and provides the reason for it."
::= { capwapBaseNotifications 8 }
-- Objects used only in notifications
Shi, et al. Informational [Page 54]
RFC 5833 CAPWAP Protocol Base MIB May 2010
-- Notification Objects
capwapBaseNotifyVarObjects OBJECT IDENTIFIER
::= { capwapBaseObjects 5 }
capwapBaseNtfWtpId OBJECT-TYPE
SYNTAX CapwapBaseWtpIdTC
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Represents the unique identifier of a WTP."
::= { capwapBaseNotifyVarObjects 1 }
capwapBaseNtfRadioId OBJECT-TYPE
SYNTAX CapwapBaseRadioIdTC
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Represents the identifier of a PHY radio on a WTP, which is
only required to be unique on a WTP.
For example, WTP A and WTP B can use the same value of
capwapBaseNtfRadioId for their first radio."
REFERENCE
"Section 4.3 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseNotifyVarObjects 2 }
capwapBaseNtfChannelType OBJECT-TYPE
SYNTAX CapwapBaseChannelTypeTC
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Represents the channel type for the CAPWAP protocol."
::= { capwapBaseNotifyVarObjects 3 }
capwapBaseNtfAuthenMethod OBJECT-TYPE
SYNTAX CapwapBaseAuthenMethodTC
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Represents the authentication method for the CAPWAP Channel."
::= { capwapBaseNotifyVarObjects 4 }
capwapBaseNtfChannelDownReason OBJECT-TYPE
SYNTAX INTEGER {
timeout(1),
rekeyFailure(2),
acRebootWtp(3),
dtlsError(4),
maxRetransmit(5)
Shi, et al. Informational [Page 55]
RFC 5833 CAPWAP Protocol Base MIB May 2010
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Represents the reason the channel is down.
The following enumerated values are supported:
timeout(1) - The keepalive timed out
rekeyFailure(2) - Rekey process failed; channel will be
broken
acRebootWtp(3) - The AC rebooted the WTP
dtlsError(4) - DTLS notifications: DTLSAborted,
DTLSReassemblyFailure, DTLSPeerDisconnect,
or frequent DTLSDecapFailure
maxRetransmit(5) - The underlying reliable transport's
RetransmitCount counter has reached the
MaxRetransmit variable"
::= { capwapBaseNotifyVarObjects 5 }
capwapBaseNtfStationIdList OBJECT-TYPE
SYNTAX LongUtf8String (SIZE (6..1024))
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Represents a list of station MAC addresses separated by
semicolons."
REFERENCE
"Section 4.6.17 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseNotifyVarObjects 6 }
capwapBaseNtfAuthenFailureReason OBJECT-TYPE
SYNTAX INTEGER {
keyMismatch(1),
invalidCert(2),
reassemblyFailure(3),
decapFailure(4),
encapFailure(5),
timeout(6),
unknown(8)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Represents the reason for WTP authorization failure.
The following enumerated values are supported:
keyMismatch(1) - WTP's and AC's keys did not match
invalidCert(2) - Certification is not valid
reassemblyFailure(3) - Fragment reassembly failure
decapFailure(4) - Decapsulation error
Shi, et al. Informational [Page 56]
RFC 5833 CAPWAP Protocol Base MIB May 2010
encapFailure(5) - Encapsulation error
timeout(6) - WaitDTLS timer timeout
unknown(8) - Unknown reason"
REFERENCE
"Section 2.3.1 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseNotifyVarObjects 7 }
capwapBaseNtfRadioOperStatusFlag OBJECT-TYPE
SYNTAX INTEGER {
operable(0),
inoperable(1)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Represents the operation status of a radio.
The following enumerated values are supported:
operable(0) - The radio is operable
inoperable(1) - The radio is inoperable, and the
capwapBaseNtfRadioStatusCause object
gives the reason in detail
Note that the CAPWAP field [RFC5415] modeled by this
object takes zero as starting value; this MIB object
follows that rule."
REFERENCE
"Section 4.6.34 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseNotifyVarObjects 8 }
capwapBaseNtfRadioStatusCause OBJECT-TYPE
SYNTAX INTEGER {
normal(0),
hwError(1),
swError(2),
adminSet(3)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Represents the reason why the radio is out of service.
The following enumerated values are supported:
normal(0) - Normal status
hwError(1) - Radio failure
swError(2) - Software failure
adminSet(3) - Administratively set
Note that the CAPWAP field [RFC5415] modeled by this
object takes zero as starting value; this MIB object
follows that rule."
REFERENCE
Shi, et al. Informational [Page 57]
RFC 5833 CAPWAP Protocol Base MIB May 2010
"Section 4.6.34 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseNotifyVarObjects 9 }
capwapBaseNtfJoinFailureReason OBJECT-TYPE
SYNTAX INTEGER {
unspecified(1),
resDepletion(2),
unknownSource(3),
incorrectData(4),
sessionIdInUse(5),
unsupportedHw(6),
unsupportedBinding(7)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Represents the reason of join failure.
The following enumerated values are supported:
unspecified(1) - Unspecified failure
resDepletion(2) - Resource depletion
unknownSource(3) - Unknown source
incorrectData(4) - Incorrect data
sessionIdInUse(5) - Session ID already in use
unsupportedHw(6) - WTP hardware not supported
unsupportedBinding(7) - Binding not supported"
REFERENCE
"Section 4.6.35 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseNotifyVarObjects 10 }
capwapBaseNtfImageFailureReason OBJECT-TYPE
SYNTAX INTEGER {
invalidChecksum(1),
invalidLength(2),
other(3),
inStorage(4)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Represents the reason of image failure.
The following enumerated values are supported:
invalidChecksum(1) - Invalid checksum
invalidLength(2) - Invalid data length
other(3) - Other error
inStorage(4) - Image already present"
REFERENCE
"Section 4.6.35 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseNotifyVarObjects 11 }
Shi, et al. Informational [Page 58]
RFC 5833 CAPWAP Protocol Base MIB May 2010
capwapBaseNtfConfigMsgErrorType OBJECT-TYPE
SYNTAX INTEGER {
unknownElement(1),
unsupportedElement(2),
unknownValue(3),
unsupportedValue(4)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Represents the type of configuration message error.
The following enumerated values are supported:
unknownElement(1) - Unknown message element
unsupportedElement(2) - Unsupported message element
unknownValue(3) - Unknown message element value
unsupportedValue(4) - Unsupported message element value"
REFERENCE
"Section 4.6.36 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseNotifyVarObjects 12 }
capwapBaseNtfMsgErrorElements OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Represents the message elements sent by the AC in the
Configuration Status Response message that caused the error."
REFERENCE
"Section 4.6.36 of CAPWAP Protocol Specification, RFC 5415."
::= { capwapBaseNotifyVarObjects 13 }
-- Notification Control
capwapBaseNotifyControlObjects OBJECT IDENTIFIER
::= { capwapBaseObjects 6 }
capwapBaseChannelUpDownNotifyEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents whether the Channel Up / Channel Down notification
should be generated.
A value of true(1) means that the notification is enabled.
A value of false(2) means that the notification is disabled.
The value of the object is persistent at restart/reboot."
DEFVAL { false }
::= { capwapBaseNotifyControlObjects 1 }
Shi, et al. Informational [Page 59]
RFC 5833 CAPWAP Protocol Base MIB May 2010
capwapBaseDecryptErrorNotifyEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents whether the decryption error notification should
be generated.
A value of true(1) means that the notification is enabled.
A value of false(2) means that the notification is disabled.
The value of the object is persistent at restart/reboot."
DEFVAL { true }
::= { capwapBaseNotifyControlObjects 2 }
capwapBaseJoinFailureNotifyEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents whether the notification of a WTP join failure
should be generated.
A value of true(1) means that the notification is enabled.
A value of false(2) means that the notification is disabled.
The value of the object is persistent at restart/reboot."
DEFVAL { true }
::= { capwapBaseNotifyControlObjects 3 }
capwapBaseImageUpgradeFailureNotifyEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents whether the notification of a WTP image upgrade
failure should be generated.
A value of true(1) means that the notification is enabled.
A value of false(2) means that the notification is disabled.
The value of the object is persistent at restart/reboot."
DEFVAL { true }
::= { capwapBaseNotifyControlObjects 4 }
capwapBaseConfigMsgErrorNotifyEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents whether the notification of configuration message
error should be generated.
A value of true(1) means that the notification is enabled.
A value of false(2) means that the notification is disabled.
Shi, et al. Informational [Page 60]
RFC 5833 CAPWAP Protocol Base MIB May 2010
The value of the object is persistent at restart/reboot."
DEFVAL { false }
::= { capwapBaseNotifyControlObjects 5 }
capwapBaseRadioOperableStatusNotifyEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents whether the notification of a radio's operational
state change should be generated.
A value of true(1) means that the notification is enabled.
A value of false(2) means that the notification is disabled.
The value of the object is persistent at restart/reboot."
DEFVAL { false }
::= { capwapBaseNotifyControlObjects 6 }
capwapBaseAuthenFailureNotifyEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Represents whether the notification of authentication failure
should be generated.
A value of true(1) means that the notification is enabled.
A value of false(2) means that the notification is disabled.
The value of the object is persistent at restart/reboot."
DEFVAL { true }
::= { capwapBaseNotifyControlObjects 7 }
-- Module compliance
capwapBaseCompliances OBJECT IDENTIFIER
::= { capwapBaseConformance 1 }
capwapBaseGroups OBJECT IDENTIFIER
::= { capwapBaseConformance 2 }
capwapBaseCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Describes the requirements for conformance to the
CAPWAP-BASE-MIB module."
MODULE IF-MIB -- The Interfaces MIB, RFC 2863
MANDATORY-GROUPS {
ifGeneralInformationGroup
}
Shi, et al. Informational [Page 61]
RFC 5833 CAPWAP Protocol Base MIB May 2010
MODULE -- this module
MANDATORY-GROUPS {
capwapBaseAcNodeGroup,
capwapBaseWtpProfileGroup,
capwapBaseWtpStateGroup,
capwapBaseWtpGroup,
capwapBaseRadioGroup,
capwapBaseStationGroup
}
GROUP capwapBaseAcNodeGroup2
DESCRIPTION
"The capwapBaseAcNodeGroup2 group is optional."
GROUP capwapBaseAcNameListGroup
DESCRIPTION
"The capwapBaseAcNameListGroup group is optional."
GROUP capwapBaseMacAclsGroup
DESCRIPTION
"The capwapBaseMacAclsGroup group is optional."
GROUP capwapBaseWtpProfileGroup2
DESCRIPTION
"The capwapBaseWtpProfileGroup2 group is optional."
GROUP capwapBaseWtpGroup2
DESCRIPTION
"The capwapBaseWtpGroup2 group is optional."
GROUP capwapBaseWtpEventsStatsGroup
DESCRIPTION
"The capwapBaseWtpEventsStatsGroup group is optional."
GROUP capwapBaseRadioEventsStatsGroup
DESCRIPTION
"The capwapBaseRadioEventsStatsGroup group is optional."
GROUP capwapBaseParametersGroup
DESCRIPTION
"The capwapBaseParametersGroup group is optional."
GROUP capwapBaseStatsGroup
DESCRIPTION
"The capwapBaseStatsGroup group is optional."
GROUP capwapBaseNotificationsGroup
DESCRIPTION
Shi, et al. Informational [Page 62]
RFC 5833 CAPWAP Protocol Base MIB May 2010
"The capwapBaseNotificationsGroup group is optional."
GROUP capwapBaseNotifyVarsGroup
DESCRIPTION
"The capwapBaseNotifyVarsGroup group is optional.
If capwapBaseNotificationsGroup is supported,
this group must be implemented."
GROUP capwapBaseNotifyControlGroup
DESCRIPTION
"The capwapBaseNotifyControlGroup group is optional.
If capwapBaseNotificationsGroup is supported,
this group must be implemented."
::= { capwapBaseCompliances 1 }
capwapBaseAcNodeGroup OBJECT-GROUP
OBJECTS {
capwapBaseWtpSessions,
capwapBaseWtpSessionsLimit,
capwapBaseStationSessions,
capwapBaseStationSessionsLimit
}
STATUS current
DESCRIPTION
"A collection of objects that is used to represent
the basic properties of the AC from the CAPWAP
protocol perspective."
::= { capwapBaseGroups 1 }
capwapBaseAcNodeGroup2 OBJECT-GROUP
OBJECTS {
capwapBaseDataChannelDTLSPolicyOptions,
capwapBaseControlChannelAuthenOptions
}
STATUS current
DESCRIPTION
"A collection of objects that is used to represent
the other properties (such as security) of the AC from
the CAPWAP protocol perspective."
::= { capwapBaseGroups 2 }
capwapBaseAcNameListGroup OBJECT-GROUP
OBJECTS {
capwapBaseAcNameListName,
capwapBaseAcNameListPriority,
capwapBaseAcNameListRowStatus
}
STATUS current
Shi, et al. Informational [Page 63]
RFC 5833 CAPWAP Protocol Base MIB May 2010
DESCRIPTION
"A collection of objects that is used to configure
the AC name list."
::= { capwapBaseGroups 3 }
capwapBaseMacAclsGroup OBJECT-GROUP
OBJECTS {
capwapBaseMacAclStationId,
capwapBaseMacAclRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects that is used to configure
the stations ACL."
::= { capwapBaseGroups 4 }
capwapBaseWtpProfileGroup OBJECT-GROUP
OBJECTS {
capwapBaseWtpProfileName,
capwapBaseWtpProfileWtpMacAddress,
capwapBaseWtpProfileWtpModelNumber,
capwapBaseWtpProfileWtpName,
capwapBaseWtpProfileWtpLocation,
capwapBaseWtpProfileRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects that is used to configure
the WTP profile."
::= { capwapBaseGroups 5 }
capwapBaseWtpProfileGroup2 OBJECT-GROUP
OBJECTS {
capwapBaseWtpProfileWtpStaticIpEnable,
capwapBaseWtpProfileWtpStaticIpType,
capwapBaseWtpProfileWtpStaticIpAddress,
capwapBaseWtpProfileWtpNetmask,
capwapBaseWtpProfileWtpGateway,
capwapBaseWtpProfileWtpFallbackEnable,
capwapBaseWtpProfileWtpEchoInterval,
capwapBaseWtpProfileWtpIdleTimeout,
capwapBaseWtpProfileWtpMaxDiscoveryInterval,
capwapBaseWtpProfileWtpReportInterval,
capwapBaseWtpProfileWtpStatisticsTimer,
capwapBaseWtpProfileWtpEcnSupport
}
STATUS current
DESCRIPTION
Shi, et al. Informational [Page 64]
RFC 5833 CAPWAP Protocol Base MIB May 2010
"A collection of optional objects that is used to
configure the WTP profile."
::= { capwapBaseGroups 6 }
capwapBaseWtpStateGroup OBJECT-GROUP
OBJECTS {
capwapBaseWtpStateWtpIpAddressType,
capwapBaseWtpStateWtpIpAddress,
capwapBaseWtpStateWtpLocalIpAddressType,
capwapBaseWtpStateWtpLocalIpAddress,
capwapBaseWtpStateWtpBaseMacAddress,
capwapBaseWtpState,
capwapBaseWtpStateWtpUpTime,
capwapBaseWtpStateWtpCurrWtpProfileId
}
STATUS current
DESCRIPTION
"A collection of objects that is used to represent
the WTP's state information."
::= { capwapBaseGroups 7 }
capwapBaseWtpGroup OBJECT-GROUP
OBJECTS {
capwapBaseWtpBaseMacAddress,
capwapBaseWtpTunnelModeOptions,
capwapBaseWtpMacTypeOptions,
capwapBaseWtpDiscoveryType,
capwapBaseWtpRadiosInUseNum,
capwapBaseWtpRadioNumLimit
}
STATUS current
DESCRIPTION
"A collection of objects that is used to represent
the properties information for the WTPs in running state."
::= { capwapBaseGroups 8 }
capwapBaseWtpGroup2 OBJECT-GROUP
OBJECTS {
capwapBaseWtpPhyIndex,
capwapBaseWtpRetransmitCount
}
STATUS current
DESCRIPTION
"A collection of optional objects that is used to represent
the properties of the WTPs in running state."
::= { capwapBaseGroups 9 }
capwapBaseRadioGroup OBJECT-GROUP
Shi, et al. Informational [Page 65]
RFC 5833 CAPWAP Protocol Base MIB May 2010
OBJECTS {
capwapBaseWirelessBindingVirtualRadioIfIndex,
capwapBaseWirelessBindingType
}
STATUS current
DESCRIPTION
"A collection of objects that is used to represent
the wireless binding type and the mappings between the
ifIndexes of WLAN Virtual Radio Interfaces and PHY radios."
::= { capwapBaseGroups 10 }
capwapBaseStationGroup OBJECT-GROUP
OBJECTS {
capwapBaseStationWtpId,
capwapBaseStationWtpRadioId,
capwapBaseStationAddedTime,
capwapBaseStationVlanName
}
STATUS current
DESCRIPTION
"A collection of objects that is used to represent
the stations' basic properties."
::= { capwapBaseGroups 11 }
capwapBaseWtpEventsStatsGroup OBJECT-GROUP
OBJECTS {
capwapBaseWtpEventsStatsRebootCount,
capwapBaseWtpEventsStatsInitCount,
capwapBaseWtpEventsStatsLinkFailureCount,
capwapBaseWtpEventsStatsSwFailureCount,
capwapBaseWtpEventsStatsHwFailureCount,
capwapBaseWtpEventsStatsOtherFailureCount,
capwapBaseWtpEventsStatsUnknownFailureCount,
capwapBaseWtpEventsStatsLastFailureType
}
STATUS current
DESCRIPTION
"A collection of objects that is used for collecting
WTP reboot count, link failure count, hardware failure
count, and so on."
::= { capwapBaseGroups 12 }
capwapBaseRadioEventsStatsGroup OBJECT-GROUP
OBJECTS {
capwapBaseRadioEventsStatsResetCount,
capwapBaseRadioEventsStatsSwFailureCount,
capwapBaseRadioEventsStatsHwFailureCount,
capwapBaseRadioEventsStatsOtherFailureCount,
Shi, et al. Informational [Page 66]
RFC 5833 CAPWAP Protocol Base MIB May 2010
capwapBaseRadioEventsStatsUnknownFailureCount,
capwapBaseRadioEventsStatsConfigUpdateCount,
capwapBaseRadioEventsStatsChannelChangeCount,
capwapBaseRadioEventsStatsBandChangeCount,
capwapBaseRadioEventsStatsCurrNoiseFloor,
capwapBaseRadioEventsStatsDecryptErrorCount,
capwapBaseRadioEventsStatsLastFailureType
}
STATUS current
DESCRIPTION
"A collection of objects that is used for collecting
radio reset count, channel change count, hardware failure
count, and so on"
::= { capwapBaseGroups 13 }
capwapBaseParametersGroup OBJECT-GROUP
OBJECTS {
capwapBaseAcMaxRetransmit,
capwapBaseAcChangeStatePendingTimer,
capwapBaseAcDataCheckTimer,
capwapBaseAcDTLSSessionDeleteTimer,
capwapBaseAcEchoInterval,
capwapBaseAcRetransmitInterval,
capwapBaseAcSilentInterval,
capwapBaseAcWaitDTLSTimer,
capwapBaseAcWaitJoinTimer,
capwapBaseAcEcnSupport
}
STATUS current
DESCRIPTION
"Objects used for the CAPWAP protocol's parameters."
::= { capwapBaseGroups 14 }
capwapBaseStatsGroup OBJECT-GROUP
OBJECTS {
capwapBaseFailedDTLSAuthFailureCount,
capwapBaseFailedDTLSSessionCount
}
STATUS current
DESCRIPTION
"Objects used for collecting the CAPWAP protocol's statistics."
::= { capwapBaseGroups 15 }
capwapBaseNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS {
capwapBaseChannelUp,
capwapBaseChannelDown,
capwapBaseDecryptErrorReport,
Shi, et al. Informational [Page 67]
RFC 5833 CAPWAP Protocol Base MIB May 2010
capwapBaseJoinFailure,
capwapBaseImageUpgradeFailure,
capwapBaseConfigMsgError,
capwapBaseRadioOperableStatus,
capwapBaseAuthenFailure
}
STATUS current
DESCRIPTION
"A collection of notifications in this MIB module."
::= { capwapBaseGroups 16 }
capwapBaseNotifyVarsGroup OBJECT-GROUP
OBJECTS {
capwapBaseNtfWtpId,
capwapBaseNtfRadioId,
capwapBaseNtfChannelType,
capwapBaseNtfAuthenMethod,
capwapBaseNtfChannelDownReason,
capwapBaseNtfStationIdList,
capwapBaseNtfAuthenFailureReason,
capwapBaseNtfRadioOperStatusFlag,
capwapBaseNtfRadioStatusCause,
capwapBaseNtfJoinFailureReason,
capwapBaseNtfImageFailureReason,
capwapBaseNtfConfigMsgErrorType,
capwapBaseNtfMsgErrorElements
}
STATUS current
DESCRIPTION
"Objects used for notifications."
::= { capwapBaseGroups 17 }
capwapBaseNotifyControlGroup OBJECT-GROUP
OBJECTS {
capwapBaseChannelUpDownNotifyEnable,
capwapBaseDecryptErrorNotifyEnable,
capwapBaseJoinFailureNotifyEnable,
capwapBaseImageUpgradeFailureNotifyEnable,
capwapBaseConfigMsgErrorNotifyEnable,
capwapBaseRadioOperableStatusNotifyEnable,
capwapBaseAuthenFailureNotifyEnable
}
STATUS current
DESCRIPTION
"Objects used to enable or disable notifications."
::= { capwapBaseGroups 18 }
END
Shi, et al. Informational [Page 68]
RFC 5833 CAPWAP Protocol Base MIB May 2010
10. Security Considerations
There are a number of management objects defined in this MIB module
with a MAX-ACCESS clause of read-write and/or read-create. Such
objects MAY be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations. The followings are the tables and objects and
their sensitivity/vulnerability:
- Unauthorized changes to the capwapBaseWtProfileTable and writable
objects under capwapBaseAcs group MAY disrupt allocation of
resources in the network. For example, a WTP's static IP address
could be changed by setting the
capwapBaseWtpProfileWtpStaticIpAddress object.
- Unauthorized changes to writable objects under the capwapBaseAc
group MAY disrupt allocation of resources in the network. For
example, an invalid value for the capwapBaseWtpSessionsLimit
object will increase the AC's traffic burden.
- Unauthorized changes to the capwapBaseMacAclTable MAY prevent
legal stations from being able to access the network, while
illegal stations are able to access it.
- Unauthorized changes to writable objects under the
capwapBaseParameters group MAY influence CAPWAP protocol behavior
and status. For example, an invalid value set for the
capwapBaseAcDataCheckTimer MAY influence the CAPWAP state machine.
Some of the readable objects in this MIB module (i.e., objects with a
MAX-ACCESS other than not-accessible) MAY be considered sensitive or
vulnerable in some network environments. It is thus important to
control even GET and/or NOTIFY access to these objects and possibly
to even encrypt the values of these objects when sending them over
the network via SNMP. The followings are the tables and objects and
their sensitivity/vulnerability:
- The capwapBaseDataChannelDTLSPolicyOptions and
capwapBaseControlChannelAuthenOptions under the capwapBaseAc group
expose the current security option for CAPWAP data and control
channels.
- The capwapBaseWtpTable exposes a WTP's important information like
tunnel mode, MAC type, and so on.
- The capwapBaseWtpEventsStatsTable exposes a WTP's failure
information.
Shi, et al. Informational [Page 69]
RFC 5833 CAPWAP Protocol Base MIB May 2010
- The capwapBaseRadioEventsStatsTable exposes a radio's failure
information.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPsec),
even then, there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete) the objects
in this MIB module.
It is RECOMMENDED that implementers consider the security features as
provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, the deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
11. IANA Considerations
11.1. IANA Considerations for CAPWAP-BASE-MIB Module
The MIB module in this document uses the following IANA-assigned
OBJECT IDENTIFIER value recorded in the SMI Numbers registry:
Descriptor OBJECT IDENTIFIER value
---------- -----------------------
capwapBaseMIB { mib-2 196 }
11.2. IANA Considerations for ifType
IANA has assigned the following ifType:
Decimal Name Description
------- ------------ -------------------------------
254 capwapWtpVirtualRadio WTP Virtual Radio Interface
12. Contributors
This MIB module is based on contributions from Long Gao.
Shi, et al. Informational [Page 70]
RFC 5833 CAPWAP Protocol Base MIB May 2010
13. Acknowledgements
Thanks to David Harrington, Dan Romascanu, Abhijit Choudhury, Bert
Wijnen, and David L. Black for helpful comments on this document and
guiding some technical solutions.
The authors also thank the following friends and coworkers: Fei Fang,
Xuebin Zhu, Hao Song, Yu Liu, Sachin Dutta, Ju Wang, Hao Wang, Yujin
Zhao, Haitao Zhang, Xiansen Cai, and Xiaolan Wan.
14. References
14.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to
Indicate Requirement Levels", BCP 14, RFC 2119,
March 1997.
[RFC2287] Krupczak, C. and J. Saperia, "Definitions of
System-Level Managed Objects for Applications",
RFC 2287, February 1998.
[RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578,
April 1999.
[RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Textual Conventions for
SMIv2", STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., and J.
Schoenwaelder, "Conformance Statements for
SMIv2", STD 58, RFC 2580, April 1999.
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces
Group MIB", RFC 2863, June 2000.
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An
Architecture for Describing Simple Network
Management Protocol (SNMP) Management
Frameworks", STD 62, RFC 3411, December 2002.
[RFC3418] Presuhn, R., "Management Information Base (MIB)
for the Simple Network Management Protocol
(SNMP)", STD 62, RFC 3418, December 2002.
Shi, et al. Informational [Page 71]
RFC 5833 CAPWAP Protocol Base MIB May 2010
[RFC4001] Daniele, M., Haberman, B., Routhier, S., and J.
Schoenwaelder, "Textual Conventions for Internet
Network Addresses", RFC 4001, February 2005.
[RFC4133] Bierman, A. and K. McCloghrie, "Entity MIB
(Version 3)", RFC 4133, August 2005.
[RFC5415] Calhoun, P., Montemurro, M., and D. Stanley,
"Control And Provisioning of Wireless Access
Points (CAPWAP) Protocol Specification",
RFC 5415, March 2009.
14.2. Informative References
[Err1832] RFC Errata, "Errata ID 1832", for RFC 5415,
<http://www.rfc-editor.org>.
[IEEE.802-11.2007] "Information technology - Telecommunications and
information exchange between systems - Local and
metropolitan area networks - Specific
requirements - Part 11: Wireless LAN Medium
Access Control (MAC) and Physical Layer (PHY)
specifications", IEEE Standard 802.11, 2007, <htt
p://standards.ieee.org/getieee802/download/
802.11-2007.pdf>.
[RFC3168] Ramakrishnan, K., Floyd, S., and D. Black, "The
Addition of Explicit Congestion Notification
(ECN) to IP", RFC 3168, September 2001.
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for
Internet-Standard Management Framework",
RFC 3410, December 2002.
[RFC4118] Yang, L., Zerfos, P., and E. Sadot, "Architecture
Taxonomy for Control and Provisioning of Wireless
Access Points (CAPWAP)", RFC 4118, June 2005.
[RFC4347] Rescorla, E. and N. Modadugu, "Datagram Transport
Layer Security", RFC 4347, April 2006.
[RFC5416] Calhoun, P., Montemurro, M., and D. Stanley,
"Control and Provisioning of Wireless Access
Points (CAPWAP) Protocol Binding for IEEE
802.11", RFC 5416, March 2009.
Shi, et al. Informational [Page 72]
RFC 5833 CAPWAP Protocol Base MIB May 2010
[RFC5834] Shi, Y., Ed., Perkins, D., Ed., Elliott, C., Ed.,
and Y. Zhang, Ed., "Control and Provisioning of
Wireless Access Points (CAPWAP) Protocol Binding
MIB for IEEE 802.11", RFC 5834, May 2010.
Authors' Addresses
Yang Shi (editor)
Hangzhou H3C Tech. Co., Ltd.
Beijing R&D Center of H3C, Digital Technology Plaza
NO. 9 Shangdi 9th Street, Haidian District
Beijing 100085
China
Phone: +86 010 82775276
EMail: rishyang@gmail.com
David T. Perkins (editor)
228 Bayview Dr.
San Carlos, CA 94070
USA
Phone: +1 408 394-8702
EMail: dperkins@dsperkins.com
Chris Elliott (editor)
1516 Kent St.
Durham, NC 27707
USA
Phone: +1 919-308-1216
EMail: chelliot@pobox.com
Yong Zhang (editor)
Fortinet, Inc.
1090 Kifer Road
Sunnyvale, CA 94086
USA
EMail: yzhang@fortinet.com
Shi, et al. Informational [Page 73]