Internet Engineering Task Force (IETF) A. Sajassi, Ed.
Request for Comments: 7623 S. Salam
Category: Standards Track Cisco
ISSN: 2070-1721 N. Bitar
Verizon
A. Isaac
Juniper
W. Henderickx
Alcatel-Lucent
September 2015
Provider Backbone Bridging Combined with Ethernet VPN (PBB-EVPN)
Abstract
This document discusses how Ethernet Provider Backbone Bridging (PBB)
can be combined with Ethernet VPN (EVPN) in order to reduce the
number of BGP MAC Advertisement routes by aggregating Customer/Client
MAC (C-MAC) addresses via Provider Backbone MAC (B-MAC) address,
provide client MAC address mobility using C-MAC aggregation, confine
the scope of C-MAC learning to only active flows, offer per-site
policies, and avoid C-MAC address flushing on topology changes. The
combined solution is referred to as PBB-EVPN.
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc7623.
Sajassi, et al. Standards Track [Page 1]
RFC 7623 PBB-EVPN September 2015
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction ....................................................3
2. Terminology .....................................................4
3. Requirements ....................................................4
3.1. MAC Advertisement Route Scalability ........................5
3.2. C-MAC Mobility Independent of B-MAC Advertisements .........5
3.3. C-MAC Address Learning and Confinement .....................5
3.4. Per-Site Policy Support ....................................6
3.5. No C-MAC Address Flushing for All-Active Multihoming .......6
4. Solution Overview ...............................................6
5. BGP Encoding ....................................................7
5.1. Ethernet Auto-Discovery Route ..............................7
5.2. MAC/IP Advertisement Route .................................7
5.3. Inclusive Multicast Ethernet Tag Route .....................8
5.4. Ethernet Segment Route .....................................8
5.5. ESI Label Extended Community ...............................8
5.6. ES-Import Route Target .....................................9
5.7. MAC Mobility Extended Community ............................9
5.8. Default Gateway Extended Community .........................9
6. Operation .......................................................9
6.1. MAC Address Distribution over Core .........................9
6.2. Device Multihoming .........................................9
6.2.1. Flow-Based Load-Balancing ...........................9
6.2.1.1. PE B-MAC Address Assignment ...............10
6.2.1.2. Automating B-MAC Address Assignment .......11
6.2.1.3. Split Horizon and Designated
Forwarder Election ........................12
6.2.2. Load-Balancing based on I-SID ......................12
6.2.2.1. PE B-MAC Address Assignment ...............12
6.2.2.2. Split Horizon and Designated
Forwarder Election ........................13
6.2.2.3. Handling Failure Scenarios ................13
Sajassi, et al. Standards Track [Page 2]
RFC 7623 PBB-EVPN September 2015
6.3. Network Multihoming .......................................14
6.4. Frame Forwarding ..........................................14
6.4.1. Unicast ............................................15
6.4.2. Multicast/Broadcast ................................15
6.5. MPLS Encapsulation of PBB Frames ..........................16
7. Minimizing ARP/ND Broadcast ....................................16
8. Seamless Interworking with IEEE 802.1aq / 802.1Qbp .............17
8.1. B-MAC Address Assignment ..................................17
8.2. IEEE 802.1aq / 802.1Qbp B-MAC Address Advertisement .......17
8.3. Operation: ................................................17
9. Solution Advantages ............................................18
9.1. MAC Advertisement Route Scalability .......................18
9.2. C-MAC Mobility Independent of B-MAC Advertisements ........18
9.3. C-MAC Address Learning and Confinement ....................19
9.4. Seamless Interworking with 802.1aq Access Networks ........19
9.5. Per-Site Policy Support ...................................20
9.6. No C-MAC Address Flushing for All-Active Multihoming ......20
10. Security Considerations .......................................20
11. IANA Considerations ...........................................20
12. References ....................................................21
12.1. Normative References .....................................21
12.2. Informative References ...................................21
Acknowledgements ..................................................22
Contributors ......................................................22
Authors' Addresses ................................................23
1. Introduction
[RFC7432] introduces a solution for multipoint Layer 2 Virtual
Private Network (L2VPN) services, with advanced multihoming
capabilities, using BGP for distributing customer/client MAC address
reachability information over the core MPLS/IP network. [PBB]
defines an architecture for Ethernet Provider Backbone Bridging
(PBB), where MAC tunneling is employed to improve service instance
and MAC address scalability in Ethernet as well as VPLS networks
[RFC7080].
In this document, we discuss how PBB can be combined with EVPN in
order to: reduce the number of BGP MAC Advertisement routes by
aggregating Customer/Client MAC (C-MAC) addresses via Provider
Backbone MAC (B-MAC) address, provide client MAC address mobility
using C-MAC aggregation, confine the scope of C-MAC learning to only
active flows, offer per-site policies, and avoid C-MAC address
flushing on topology changes. The combined solution is referred to
as PBB-EVPN.
Sajassi, et al. Standards Track [Page 3]
RFC 7623 PBB-EVPN September 2015
2. Terminology
ARP: Address Resolution Protocol
BEB: Backbone Edge Bridge
B-MAC: Backbone MAC
B-VID: Backbone VLAN ID
CE: Customer Edge
C-MAC: Customer/Client MAC
ES: Ethernet Segment
ESI: Ethernet Segment Identifier
EVI: EVPN Instance
EVPN: Ethernet VPN
I-SID: Service Instance Identifier (24 bits and global within a PBB
network see [RFC7080])
LSP: Label Switched Path
MP2MP: Multipoint to Multipoint
MP2P: Multipoint to Point
NA: Neighbor Advertisement
ND: Neighbor Discovery
P2MP: Point to Multipoint
P2P: Point to Point
PBB: Provider Backbone Bridge
PE: Provider Edge
RT: Route Target
VPLS: Virtual Private LAN Service
Single-Active Redundancy Mode: When only a single PE, among a group
of PEs attached to an Ethernet segment, is allowed to forward traffic
to/from that Ethernet segment, then the Ethernet segment is defined
to be operating in Single-Active redundancy mode.
All-Active Redundancy Mode: When all PEs attached to an Ethernet
segment are allowed to forward traffic to/from that Ethernet segment,
then the Ethernet segment is defined to be operating in All-Active
redundancy mode.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in BCP 14 [RFC2119].
3. Requirements
The requirements for PBB-EVPN include all the requirements for EVPN
that were described in [RFC7209], in addition to the following:
Sajassi, et al. Standards Track [Page 4]
RFC 7623 PBB-EVPN September 2015
3.1. MAC Advertisement Route Scalability
In typical operation, an EVPN PE sends a BGP MAC Advertisement route
per C-MAC address. In certain applications, this poses scalability
challenges, as is the case in data center interconnect (DCI)
scenarios where the number of virtual machines (VMs), and hence the
number of C-MAC addresses, can be in the millions. In such
scenarios, it is required to reduce the number of BGP MAC
Advertisement routes by relying on a 'MAC summarization' scheme, as
is provided by PBB.
3.2. C-MAC Mobility Independent of B-MAC Advertisements
Certain applications, such as virtual machine mobility, require
support for fast C-MAC address mobility. For these applications,
when using EVPN, the virtual machine MAC address needs to be
transmitted in BGP MAC Advertisement route. Otherwise, traffic would
be forwarded to the wrong segment when a virtual machine moves from
one ES to another. This means MAC address prefixes cannot be used in
data center applications.
In order to support C-MAC address mobility, while retaining the
scalability benefits of MAC summarization, PBB technology is used.
It defines a B-MAC address space that is independent of the C-MAC
address space, and aggregates C-MAC addresses via a single B-MAC
address.
3.3. C-MAC Address Learning and Confinement
In EVPN, all the PE nodes participating in the same EVPN instance are
exposed to all the C-MAC addresses learned by any one of these PE
nodes because a C-MAC learned by one of the PE nodes is advertised in
BGP to other PE nodes in that EVPN instance. This is the case even
if some of the PE nodes for that EVPN instance are not involved in
forwarding traffic to, or from, these C-MAC addresses. Even if an
implementation does not install hardware forwarding entries for C-MAC
addresses that are not part of active traffic flows on that PE, the
device memory is still consumed by keeping record of the C-MAC
addresses in the routing information base (RIB) table. In network
applications with millions of C-MAC addresses, this introduces a non-
trivial waste of PE resources. As such, it is required to confine
the scope of visibility of C-MAC addresses to only those PE nodes
that are actively involved in forwarding traffic to, or from, these
addresses.
Sajassi, et al. Standards Track [Page 5]
RFC 7623 PBB-EVPN September 2015
3.4. Per-Site Policy Support
In many applications, it is required to be able to enforce
connectivity policy rules at the granularity of a site (or segment).
This includes the ability to control which PE nodes in the network
can forward traffic to, or from, a given site. Both EVPN and PBB-
EVPN are capable of providing this granularity of policy control. In
the case where the policy needs to be at the granularity of per C-MAC
address, then the C-MAC address should be learned in the control
plane (in BGP) per [RFC7432].
3.5. No C-MAC Address Flushing for All-Active Multihoming
Just as in [RFC7432], it is required to avoid C-MAC address flushing
upon link, port, or node failure for All-Active multihomed segments.
4. Solution Overview
The solution involves incorporating IEEE Backbone Edge Bridge (BEB)
functionality on the EVPN PE nodes similar to PBB-VPLS, where BEB
functionality is incorporated in the VPLS PE nodes. The PE devices
would then receive 802.1Q Ethernet frames from their attachment
circuits, encapsulate them in the PBB header, and forward the frames
over the IP/MPLS core. On the egress EVPN PE, the PBB header is
removed following the MPLS disposition, and the original 802.1Q
Ethernet frame is delivered to the customer equipment.
BEB +--------------+ BEB
|| | | ||
\/ | | \/
+----+ AC1 +----+ | | +----+ +----+
| CE1|-----| | | | | |---| CE2|
+----+\ | PE1| | IP/MPLS | | PE3| +----+
\ +----+ | Network | +----+
\ | |
AC2\ +----+ | |
\| | | |
| PE2| | |
+----+ | |
/\ +--------------+
||
BEB
<-802.1Q-> <------PBB over MPLS------> <-802.1Q->
Figure 1: PBB-EVPN Network
Sajassi, et al. Standards Track [Page 6]
RFC 7623 PBB-EVPN September 2015
The PE nodes perform the following functions:
- Learn customer/client MAC addresses (C-MACs) over the attachment
circuits in the data plane, per normal bridge operation.
- Learn remote C-MAC to B-MAC bindings in the data plane for traffic
received from the core per the bridging operation described in
[PBB].
- Advertise local B-MAC address reachability information in BGP to
all other PE nodes in the same set of service instances. Note
that every PE has a set of B-MAC addresses that uniquely
identifies the device. B-MAC address assignment is described in
details in Section 6.2.2.
- Build a forwarding table from remote BGP advertisements received
associating remote B-MAC addresses with remote PE IP addresses and
the associated MPLS label(s).
5. BGP Encoding
PBB-EVPN leverages the same BGP routes and attributes defined in
[RFC7432], adapted as described below.
5.1. Ethernet Auto-Discovery Route
This route and all of its associated modes are not needed in PBB-EVPN
because PBB encapsulation provides the required level of indirection
for C-MAC addresses -- i.e., an ES can be represented by a B-MAC
address for the purpose of data-plane learning/forwarding.
The receiving PE knows that it need not wait for the receipt of the
Ethernet A-D (auto-discovery) route for route resolution by means of
the reserved ESI encoded in the MAC Advertisement route: the ESI
values of 0 and MAX-ESI indicate that the receiving PE can resolve
the path without an Ethernet A-D route.
5.2. MAC/IP Advertisement Route
The EVPN MAC/IP Advertisement route is used to distribute B-MAC
addresses of the PE nodes instead of the C-MAC addresses of end-
stations/hosts. This is because the C-MAC addresses are learned in
the data plane for traffic arriving from the core. The MAC
Advertisement route is encoded as follows:
- The MAC address field contains the B-MAC address.
- The Ethernet Tag field is set to 0.
Sajassi, et al. Standards Track [Page 7]
RFC 7623 PBB-EVPN September 2015
- The Ethernet Segment Identifier field must be set to either 0 (for
single-homed segments or multihomed segments with per-I-SID load-
balancing) or to MAX-ESI (for multihomed segments with per-flow
load-balancing). All other values are not permitted.
- All other fields are set as defined in [RFC7432].
This route is tagged with the RT corresponding to its EVI. This EVI
is analogous to a B-VID.
5.3. Inclusive Multicast Ethernet Tag Route
This route is used for multicast pruning per I-SID. It is used for
auto-discovery of PEs participating in a given I-SID so that a
multicast tunnel (MP2P, P2P, P2MP, or MP2MP LSP) can be set up for
that I-SID. [RFC7080] uses multicast pruning per I-SID based on
[MMRP], which is a soft-state protocol. The advantages of multicast
pruning using this BGP route over [MMRP] are that a) it scales very
well for a large number of PEs and b) it works with any type of LSP
(MP2P, P2P, P2MP, or MP2MP); whereas, [MMRP] only works over P2P
pseudowires. The Inclusive Multicast Ethernet Tag route is encoded
as follows:
- The Ethernet Tag field is set with the appropriate I-SID value.
- All other fields are set as defined in [RFC7432].
This route is tagged with an RT. This RT SHOULD be set to a value
corresponding to its EVI (which is analogous to a B-VID). The RT for
this route MAY also be auto-derived from the corresponding Ethernet
Tag (I-SID) based on the procedure specified in Section 5.1.2.1 of
[OVERLAY].
5.4. Ethernet Segment Route
This route is used for auto-discovery of PEs belonging to a given
redundancy group (e.g., attached to a given ES) per [RFC7432].
5.5. ESI Label Extended Community
This extended community is not used in PBB-EVPN. In [RFC7432], this
extended community is used along with the Ethernet A-D route to
advertise an MPLS label for the purpose of split-horizon filtering.
Since in PBB-EVPN, the split-horizon filtering is performed natively
using B-MAC source address, there is no need for this extended
community.
Sajassi, et al. Standards Track [Page 8]
RFC 7623 PBB-EVPN September 2015
5.6. ES-Import Route Target
This RT is used as defined in [RFC7432].
5.7. MAC Mobility Extended Community
This extended community is defined in [RFC7432] and it is used with a
MAC route (B-MAC route in case of PBB-EVPN). The B-MAC route is
tagged with the RT corresponding to its EVI (which is analogous to a
B-VID). When this extended community is used along with a B-MAC
route in PBB-EVPN, it indicates that all C-MAC addresses associated
with that B-MAC address across all corresponding I-SIDs must be
flushed.
When a PE first advertises a B-MAC, it MAY advertise it with this
extended community where the sticky/static flag is set to 1 and the
sequence number is set to zero. In such cases where the PE wants to
signal the stickiness of a B-MAC, then when a flush indication is
needed, the PE advertises the B-MAC along with the MAC Mobility
extended community where the sticky/static flag remains set and the
sequence number is incremented.
5.8. Default Gateway Extended Community
This extended community is not used in PBB-EVPN.
6. Operation
This section discusses the operation of PBB-EVPN, specifically in
areas where it differs from [RFC7432].
6.1. MAC Address Distribution over Core
In PBB-EVPN, host MAC addresses (i.e., C-MAC addresses) need not be
distributed in BGP. Rather, every PE independently learns the C-MAC
addresses in the data plane via normal bridging operation. Every PE
has a set of one or more unicast B-MAC addresses associated with it,
and those are the addresses distributed over the core in MAC
Advertisement routes.
6.2. Device Multihoming
6.2.1. Flow-Based Load-Balancing
This section describes the procedures for supporting device
multihoming in an All-Active redundancy mode (i.e., flow-based load-
balancing).
Sajassi, et al. Standards Track [Page 9]
RFC 7623 PBB-EVPN September 2015
6.2.1.1. PE B-MAC Address Assignment
In [PBB], every BEB is uniquely identified by one or more B-MAC
addresses. These addresses are usually locally administered by the
service provider. For PBB-EVPN, the choice of B-MAC address(es) for
the PE nodes must be examined carefully as it has implications on the
proper operation of multihoming. In particular, for the scenario
where a CE is multihomed to a number of PE nodes with All-Active
redundancy mode, a given C-MAC address would be reachable via
multiple PE nodes concurrently. Given that any given remote PE will
bind the C-MAC address to a single B-MAC address, then the various PE
nodes connected to the same CE must share the same B-MAC address.
Otherwise, the MAC address table of the remote PE nodes will keep
oscillating between the B-MAC addresses of the various PE devices.
For example, consider the network of Figure 1, and assume that PE1
has B-MAC address BM1 and PE2 has B-MAC address BM2. Also, assume
that both links from CE1 to the PE nodes are part of the same
Ethernet link aggregation group. If BM1 is not equal to BM2, the
consequence is that the MAC address table on PE3 will keep
oscillating such that the C-MAC address M1 of CE1 would flip-flop
between BM1 or BM2, depending on the load-balancing decision on CE1
for traffic destined to the core.
Considering that there could be multiple sites (e.g., CEs) that are
multihomed to the same set of PE nodes, then it is required for all
the PE devices in a redundancy group to have a unique B-MAC address
per site. This way, it is possible to achieve fast convergence in
the case where a link or port failure impacts the attachment circuit
connecting a single site to a given PE.
+---------+
+-------+ PE1 | IP/MPLS |
/ | |
CE1 | Network | PEr
M1 \ | |
+-------+ PE2 | |
/-------+ | |
/ | |
CE2 | |
M2 \ | |
\ | |
+------+ PE3 +---------+
Figure 2: B-MAC Address Assignment
In the example network shown in Figure 2 above, two sites
corresponding to CE1 and CE2 are dual-homed to PE1/PE2 and PE2/PE3,
respectively. Assume that BM1 is the B-MAC used for the site
Sajassi, et al. Standards Track [Page 10]
RFC 7623 PBB-EVPN September 2015
corresponding to CE1. Similarly, BM2 is the B-MAC used for the site
corresponding to CE2. On PE1, a single B-MAC address (BM1) is
required for the site corresponding to CE1. On PE2, two B-MAC
addresses (BM1 and BM2) are required, one per site. Whereas on PE3,
a single B-MAC address (BM2) is required for the site corresponding
to CE2. All three PE nodes would advertise their respective B-MAC
addresses in BGP using the MAC Advertisement routes defined in
[RFC7432]. The remote PE, PEr, would learn via BGP that BM1 is
reachable via PE1 and PE2, whereas BM2 is reachable via both PE2 and
PE3. Furthermore, PEr establishes, via the PBB bridge learning
procedure, that C-MAC M1 is reachable via BM1, and C-MAC M2 is
reachable via BM2. As a result, PEr can load-balance traffic
destined to M1 between PE1 and PE2, as well as traffic destined to M2
between both PE2 and PE3. In the case of a failure that causes, for
example, CE1 to be isolated from PE1, the latter can withdraw the
route it has advertised for BM1. This way, PEr would update its path
list for BM1 and will send all traffic destined to M1 over to PE2
only.
6.2.1.2. Automating B-MAC Address Assignment
The PE B-MAC address used for single-homed or Single-Active sites can
be automatically derived from the hardware (using for example the
backplane's address and/or PE's reserved MAC pool ). However, the
B-MAC address used for All-Active sites must be coordinated among the
redundancy group members. To automate the assignment of this latter
address, the PE can derive this B-MAC address from the MAC address
portion of the CE's Link Aggregation Control Protocol (LACP) System
Identifier by flipping the 'Locally Administered' bit of the CE's
address. This guarantees the uniqueness of the B-MAC address within
the network, and ensures that all PE nodes connected to the same All-
Active CE use the same value for the B-MAC address.
Note that with this automatic provisioning of the B-MAC address
associated with All-Active CEs, it is not possible to support the
uncommon scenario where a CE has multiple link bundles within the
same LACP session towards the PE nodes, and the service involves
hair-pinning traffic from one bundle to another. This is because the
split-horizon filtering relies on B-MAC addresses rather than Site-ID
Labels (as will be described in the next section). The operator must
explicitly configure the B-MAC address for this fairly uncommon
service scenario.
Whenever a B-MAC address is provisioned on the PE, either manually or
automatically (as an outcome of CE auto-discovery), the PE MUST
transmit a MAC Advertisement route for the B-MAC address with a
downstream assigned MPLS label that uniquely identifies that address
Sajassi, et al. Standards Track [Page 11]
RFC 7623 PBB-EVPN September 2015
on the advertising PE. The route is tagged with the RTs of the
associated EVIs as described above.
6.2.1.3. Split Horizon and Designated Forwarder Election
[RFC7432] relies on split-horizon filtering for a multi-homed ES,
where the ES label is used for egress filtering on the attachment
circuit in order to prevent forwarding loops. In PBB-EVPN, the B-MAC
source address can be used for the same purpose, as it uniquely
identifies the originating site of a given frame. As such, ES labels
are not used in PBB-EVPN, and the egress split-horizon filtering is
done based on the B-MAC source address. It is worth noting here that
[PBB] defines this B-MAC address-based filtering function as part of
the I-Component options; hence, no new functions are required to
support split-horizon filtering beyond what is already defined in
[PBB].
The Designated Forwarder (DF) election procedures are defined in
[RFC7432].
6.2.2. Load-Balancing based on I-SID
This section describes the procedures for supporting device
multihoming in a Single-Active redundancy mode with per-I-SID load-
balancing.
6.2.2.1. PE B-MAC Address Assignment
In the case where per-I-SID load-balancing is desired among the PE
nodes in a given redundancy group, multiple unicast B-MAC addresses
are allocated per multihomed ES: Each PE connected to the multihomed
segment is assigned a unique B-MAC. Every PE then advertises its
B-MAC address using the BGP MAC Advertisement route. In this mode of
operation, two B-MAC address-assignment models are possible:
- The PE may use a shared B-MAC address for all its single-homed
segments and/or all its multi-homed Single-Active segments (e.g.,
segments operating in per-I-SID load-balancing mode).
- The PE may use a dedicated B-MAC address for each ES operating
with per-I-SID load-balancing mode.
A PE implementation MAY choose to support either the shared B-MAC
address model or the dedicated B-MAC address model without causing
any interoperability issues. The advantage of the dedicated B-MAC
over the shared B-MAC address for multi-homed Single-Active segments,
is that when C-MAC flushing is needed, fewer C-MAC addresses are
impacted. Furthermore, it gives the disposition PE the ability to
Sajassi, et al. Standards Track [Page 12]
RFC 7623 PBB-EVPN September 2015
avoid C-MAC destination address lookup even though source C-MAC
learning is still required in the data plane. Its disadvantage is
that there are additional B-MAC advertisements in BGP.
A remote PE initially floods traffic to a destination C-MAC address,
located in a given multihomed ES, to all the PE nodes configured with
that I-SID. Then, when reply traffic arrives at the remote PE, it
learns (in the data path) the B-MAC address and associated next-hop
PE to use for said C-MAC address.
6.2.2.2. Split Horizon and Designated Forwarder Election
The procedures are similar to the flow-based load-balancing case,
with the only difference being that the DF filtering must be applied
to unicast as well as multicast traffic, and in both core-to-segment
as well as segment-to-core directions.
6.2.2.3. Handling Failure Scenarios
When a PE connected to a multihomed ES loses connectivity to the
segment, due to link or port failure, it needs to notify the remote
PEs to trigger C-MAC address flushing. This can be achieved in one
of two ways, depending on the B-MAC assignment model:
- If the PE uses a shared B-MAC address for multiple Ethernet
segments, then the C-MAC flushing is signaled by means of having
the failed PE re-advertise the MAC Advertisement route for the
associated B-MAC, tagged with the MAC Mobility extended community
attribute. The value of the Counter field in that attribute must
be incremented prior to advertisement. This causes the remote PE
nodes to flush all C-MAC addresses associated with the B-MAC in
question. This is done across all I-SIDs that are mapped to the
EVI of the withdrawn MAC route.
- If the PE uses a dedicated B-MAC address for each ES operating
under per-I-SID load-balancing mode, the failed PE simply
withdraws the B-MAC route previously advertised for that segment.
This causes the remote PE nodes to flush all C-MAC addresses
associated with the B-MAC in question. This is done across all
I-SIDs that are mapped to the EVI of the withdrawn MAC route.
When a PE connected to a multihomed ES fails (i.e., node failure) or
when the PE becomes completely isolated from the EVPN network, the
remote PEs will start purging the MAC Advertisement routes that were
advertised by the failed PE. This is done either as an outcome of
the remote PEs detecting that the BGP session to the failed PE has
gone down, or by having a Route Reflector withdrawing all the routes
that were advertised by the failed PE. The remote PEs, in this case,
Sajassi, et al. Standards Track [Page 13]
RFC 7623 PBB-EVPN September 2015
will perform C-MAC address flushing as an outcome of the MAC
Advertisement route withdrawals.
For all failure scenarios (link/port failure, node failure, and PE
node isolation), when the fault condition clears, the recovered PE
re-advertises the associated ES route to other members of its
redundancy group. This triggers the backup PE(s) in the redundancy
group to block the I-SIDs for which the recovered PE is a DF. When a
backup PE blocks the I-SIDs, it triggers a C-MAC address flush
notification to the remote PEs by re-advertising the MAC
Advertisement route for the associated B-MAC, with the MAC Mobility
extended community attribute. The value of the Counter field in that
attribute must be incremented prior to advertisement. This causes
the remote PE nodes to flush all C-MAC addresses associated with the
B-MAC in question. This is done across all I-SIDs that are mapped to
the EVI of the withdrawn/re-advertised MAC route.
6.3. Network Multihoming
When an Ethernet network is multihomed to a set of PE nodes running
PBB-EVPN, Single-Active redundancy model can be supported with per-
service instance (i.e., I-SID) load-balancing. In this model, DF
election is performed to ensure that a single PE node in the
redundancy group is responsible for forwarding traffic associated
with a given I-SID. This guarantees that no forwarding loops are
created. Filtering based on DF state applies to both unicast and
multicast traffic, and in both access-to-core as well as core-to-
access directions just like a Single-Active multihomed device
scenario (but unlike an All-Active multihomed device scenario where
DF filtering is limited to multi-destination frames in the core-to-
access direction). Similar to a Single-Active multihomed device
scenario, with load-balancing based on I-SID, a unique B-MAC address
is assigned to each of the PE nodes connected to the multihomed
network (segment).
6.4. Frame Forwarding
The frame-forwarding functions are divided in between the Bridge
Module, which hosts the [PBB] BEB functionality, and the MPLS
Forwarder which handles the MPLS imposition/disposition. The details
of frame forwarding for unicast and multi-destination frames are
discussed next.
Sajassi, et al. Standards Track [Page 14]
RFC 7623 PBB-EVPN September 2015
6.4.1. Unicast
Known unicast traffic received from the Attachment Circuit (AC) will
be PBB-encapsulated by the PE using the B-MAC source address
corresponding to the originating site. The unicast B-MAC destination
address is determined based on a lookup of the C-MAC destination
address (the binding of the two is done via transparent learning of
reverse traffic). The resulting frame is then encapsulated with an
LSP tunnel label and an EVPN label associated with the B-MAC
destination address. If per flow load-balancing over ECMPs in the
MPLS core is required, then a flow label is added below the label
associated with the B-MAC address in the label stack.
For unknown unicast traffic, the PE forwards these frames over the
MPLS core. When these frames are to be forwarded, then the same set
of options used for forwarding multicast/broadcast frames (as
described in next section) are used.
6.4.2. Multicast/Broadcast
Multi-destination frames received from the AC will be PBB-
encapsulated by the PE using the B-MAC source address corresponding
to the originating site. The multicast B-MAC destination address is
selected based on the value of the I-SID as defined in [PBB]. The
resulting frame is then forwarded over the MPLS core using one of the
following two options:
Option 1: the MPLS Forwarder can perform ingress replication over a
set of MP2P or P2P tunnel LSPs. The frame is encapsulated with a
tunnel LSP label and the EVPN ingress replication label advertised
in the Inclusive Multicast Ethernet Tag [RFC7432].
Option 2: the MPLS Forwarder can use P2MP tunnel LSP per the
procedures defined in [RFC7432]. This includes either the use of
Inclusive or Aggregate Inclusive trees. Furthermore, the MPLS
Forwarder can use MP2MP tunnel LSP if Inclusive trees are used.
Note that the same procedures for advertising and handling the
Inclusive Multicast Ethernet Tag defined in [RFC7432] apply here.
Sajassi, et al. Standards Track [Page 15]
RFC 7623 PBB-EVPN September 2015
6.5. MPLS Encapsulation of PBB Frames
The encapsulation for the transport of PBB frames over MPLS is
similar to that of classical Ethernet, albeit with the additional PBB
header, as shown in the figure below:
+------------------+
| IP/MPLS Header |
+------------------+
| PBB Header |
+------------------+
| Ethernet Header |
+------------------+
| Ethernet Payload |
+------------------+
| Ethernet FCS |
+------------------+
Figure 3: PBB over MPLS Encapsulation
7. Minimizing ARP/ND Broadcast
The PE nodes MAY implement an ARP/ND-proxy function in order to
minimize the volume of ARP/ND traffic that is broadcasted over the
MPLS network. In case of ARP proxy, this is achieved by having each
PE node snoop on ARP request and response messages received over the
access interfaces or the MPLS core. The PE builds a cache of IP/MAC
address bindings from these snooped messages. The PE then uses this
cache to respond to ARP requests ingress on access ports and target
hosts that are in remote sites. If the PE finds a match for the IP
address in its ARP cache, it responds back to the requesting host and
drops the request. Otherwise, if it does not find a match, then the
request is flooded over the MPLS network using either ingress
replication or P2MP LSPs. In case of ND proxy, this is achieved
similar to the above but with ND/NA messages per [RFC4389].
Sajassi, et al. Standards Track [Page 16]
RFC 7623 PBB-EVPN September 2015
8. Seamless Interworking with IEEE 802.1aq / 802.1Qbp
+--------------+
| |
+---------+ | MPLS | +---------+
+----+ | | +----+ +----+ | | +----+
|SW1 |--| | | PE1| | PE2| | |--| SW3|
+----+ | 802.1aq |---| | | |--| 802.1aq | +----+
+----+ | .1Qbp | +----+ +----+ | .1Qbp | +----+
|SW2 |--| | | Backbone | | |--| SW4|
+----+ +---------+ +--------------+ +---------+ +----+
|<------ IS-IS -------->|<-----BGP----->|<------ IS-IS ------>| CP
|<------------------------- PBB -------------------------->| DP
|<----MPLS----->|
Legend: CP = Control-Plane View
DP = Data-Plane View
Figure 4: Interconnecting 802.1aq / 802.1Qbp Networks with PBB-EVPN
8.1. B-MAC Address Assignment
The B-MAC addresses need to be globally unique across all networks
including PBB-EVPN and IEEE 802.1aq / 802.1Qbp networks. The B-MAC
addresses used for single-homed and Single-Active Ethernet segments
should be unique because they are typically auto-derived from the
PE's pools of reserved MAC addresses that are unique. The B-MAC
addresses used for All-Active Ethernet segments should also be unique
given that each network operator typically has its own assigned
Organizationally Unique Identifier (OUI) and thus can assign its own
unique MAC addresses.
8.2. IEEE 802.1aq / 802.1Qbp B-MAC Address Advertisement
B-MAC addresses associated with 802.1aq / 802.1Qbp switches are
advertised using the EVPN MAC/IP route advertisement already defined
in [RFC7432].
8.3. Operation:
When a PE receives a PBB-encapsulated Ethernet frame from the access
side, it performs a lookup on the B-MAC destination address to
identify the next hop. If the lookup yields that the next hop is a
remote PE, the local PE would then encapsulate the PBB frame in MPLS.
The label stack comprises of the VPN label (advertised by the remote
Sajassi, et al. Standards Track [Page 17]
RFC 7623 PBB-EVPN September 2015
PE), followed by an LSP/IGP label. From that point onwards, regular
MPLS forwarding is applied.
On the disposition PE, assuming penultimate-hop-popping is employed,
the PE receives the MPLS-encapsulated PBB frame with a single label:
the VPN label. The value of the label indicates to the disposition
PE that this is a PBB frame, so the label is popped, the TTL field
(in the 802.1Qbp F-Tag) is reinitialized, and normal PBB processing
is employed from this point onwards.
9. Solution Advantages
In this section, we discuss the advantages of the PBB-EVPN solution
in the context of the requirements set forth in Section 3.
9.1. MAC Advertisement Route Scalability
In PBB-EVPN, the number of MAC Advertisement routes is a function of
the number of Ethernet segments (e.g., sites) rather than the number
of hosts/servers. This is because the B-MAC addresses of the PEs,
rather than C-MAC addresses (of hosts/servers), are being advertised
in BGP. As discussed above, there's a one-to-one mapping between
All-Active multihomed segments and their associated B-MAC addresses;
there can be either a one-to-one or many-to-one mapping between
Single-Active multihomed segments and their associated B-MAC
addresses; and finally there is a many-to-one mapping between single-
home sites and their associated B-MAC addresses on a given PE. This
means a single B-MAC is associated with one or more segments where
each segment can be associated with many C-MAC addresses. As a
result, the volume of MAC Advertisement routes in PBB-EVPN may be
multiple orders of magnitude less than EVPN.
9.2. C-MAC Mobility Independent of B-MAC Advertisements
As described above, in PBB-EVPN, a single B-MAC address can aggregate
many C-MAC addresses. Given that B-MAC addresses are associated with
segments attached to a PE or to the PE itself, their locations are
fixed and thus not impacted what so ever by C-MAC mobility.
Therefore, C-MAC mobility does not affect B-MAC addresses (e.g., any
re-advertisements of them). This is because the association of C-MAC
address to B-MAC address is learned in the data-plane and C-MAC
addresses are not advertised in BGP. Aggregation via B-MAC addresses
in PBB-EVPN performs much better than EVPN.
Sajassi, et al. Standards Track [Page 18]
RFC 7623 PBB-EVPN September 2015
To illustrate how this compares to EVPN, consider the following
example:
If a PE running EVPN advertises reachability for N MAC addresses
via a particular segment, and then 50% of the MAC addresses in
that segment move to other segments (e.g., due to virtual machine
mobility), then N/2 additional MAC Advertisement routes need to be
sent for the MAC addresses that have moved. With PBB-EVPN, on the
other hand, the B-MAC addresses that are statically associated
with PE nodes are not subject to mobility. As C-MAC addresses
move from one segment to another, the binding of C-MAC to B-MAC
addresses is updated via data-plane learning in PBB-EVPN.
9.3. C-MAC Address Learning and Confinement
In PBB-EVPN, C-MAC address reachability information is built via
data-plane learning. As such, PE nodes not participating in active
conversations involving a particular C-MAC address will purge that
address from their forwarding tables. Furthermore, since C-MAC
addresses are not distributed in BGP, PE nodes will not maintain any
record of them in the control-plane routing table.
9.4. Seamless Interworking with 802.1aq Access Networks
Consider the scenario where two access networks, one running MPLS and
the other running 802.1aq, are interconnected via an MPLS backbone
network. The figure below shows such an example network.
+--------------+
| |
+---------+ | MPLS | +---------+
+----+ | | +----+ +----+ | | +----+
| CE |--| | | PE1| | PE2| | |--| CE |
+----+ | 802.1aq |---| | | |--| MPLS | +----+
+----+ | | +----+ +----+ | | +----+
| CE |--| | | Backbone | | |--| CE |
+----+ +---------+ +--------------+ +---------+ +----+
Figure 5: Interoperability with 802.1aq
If the MPLS backbone network employs EVPN, then the 802.1aq data-
plane encapsulation must be terminated on PE1 or the edge device
connecting to PE1. Either way, all the PE nodes that are part of the
associated service instances will be exposed to all the C-MAC
addresses of all hosts/servers connected to the access networks.
However, if the MPLS backbone network employs PBB-EVPN, then the
802.1aq encapsulation can be extended over the MPLS backbone, thereby
maintaining C-MAC address transparency on PE1. If PBB-EVPN is also
Sajassi, et al. Standards Track [Page 19]
RFC 7623 PBB-EVPN September 2015
extended over the MPLS access network on the right, then C-MAC
addresses would be transparent to PE2 as well.
9.5. Per-Site Policy Support
In PBB-EVPN, the per-site policy can be supported via B-MAC addresses
via assigning a unique B-MAC address for every site/segment
(typically multihomed but can also be single-homed). Given that the
B-MAC addresses are sent in BGP MAC/IP route advertisement, it is
possible to define per-site (i.e., B-MAC) forwarding policies
including policies for E-TREE service.
9.6. No C-MAC Address Flushing for All-Active Multihoming
Just as in [RFC7432], with PBB-EVPN, it is possible to avoid C-MAC
address flushing upon topology change affecting an All-Active
multihomed segment. To illustrate this, consider the example network
of Figure 1. Both PE1 and PE2 advertise the same B-MAC address (BM1)
to PE3. PE3 then learns the C-MAC addresses of the servers/hosts
behind CE1 via data-plane learning. If AC1 fails, then PE3 does not
need to flush any of the C-MAC addresses learned and associated with
BM1. This is because PE1 will withdraw the MAC Advertisement routes
associated with BM1, thereby leading PE3 to have a single adjacency
(to PE2) for this B-MAC address. Therefore, the topology change is
communicated to PE3 and no C-MAC address flushing is required.
10. Security Considerations
All the security considerations in [RFC7432] apply directly to this
document because this document leverages the control plane described
in [RFC7432] and their associated procedures -- although not the
complete set but rather a subset.
This document does not introduce any new security considerations
beyond that of [RFC7432] and [RFC4761] because advertisements and
processing of B-MAC addresses follow that of [RFC7432] and processing
of C-MAC addresses follow that of [RFC4761] -- i.e, B-MAC addresses
are learned in the control plane and C-MAC addresses are learned in
data plane.
11. IANA Considerations
There are no additional IANA considerations for PBB-EVPN beyond what
is already described in [RFC7432].
Sajassi, et al. Standards Track [Page 20]
RFC 7623 PBB-EVPN September 2015
12. References
12.1. Normative References
[PBB] IEEE, "IEEE Standard for Local and metropolitan area
networks - Media Access Control (MAC) Bridges and Virtual
Bridged Local Area Networks", Clauses 25 and 26, IEEE Std
802.1Q, DOI 10.1109/IEEESTD.2011.6009146.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.
[RFC7432] Sajassi, A., Ed., Aggarwal, R., Bitar, N., Isaac, A.,
Uttaro, J., Drake, J., and W. Henderickx, "BGP MPLS-Based
Ethernet VPN", RFC 7432, DOI 10.17487/RFC7432, February
2015, <http://www.rfc-editor.org/info/rfc7432>.
12.2. Informative References
[MMRP] IEEE, "IEEE Standard for Local and metropolitan area
networks - Media Access Control (MAC) Bridges and Virtual
Bridged Local Area Networks", Clause 10, IEEE Std 802.1Q,
DOI 10.1109/IEEESTD.2011.6009146.
[OVERLAY] Sajassi, A., Ed., Drake, J., Ed., Bitar, N., Isaac, A.,
Uttaro, J., Henderickx, W., Shekhar, R., Salam, S., Patel,
K., Rao, D., and S. Thoria, "A Network Virtualization
Overlay Solution using EVPN",
draft-ietf-bess-evpn-overlay-01, February 2015.
[RFC4389] Thaler, D., Talwar, M., and C. Patel, "Neighbor Discovery
Proxies (ND Proxy)", RFC 4389, DOI 10.17487/RFC4389, April
2006, <http://www.rfc-editor.org/info/rfc4389>.
[RFC4761] Kompella, K., Ed., and Y. Rekhter, Ed., "Virtual Private
LAN Service (VPLS) Using BGP for Auto-Discovery and
Signaling", RFC 4761, DOI 10.17487/RFC4761, January 2007,
<http://www.rfc-editor.org/info/rfc4761>.
[RFC7080] Sajassi, A., Salam, S., Bitar, N., and F. Balus, "Virtual
Private LAN Service (VPLS) Interoperability with Provider
Backbone Bridges", RFC 7080, DOI 10.17487/RFC7080,
December 2013, <http://www.rfc-editor.org/info/rfc7080>.
Sajassi, et al. Standards Track [Page 21]
RFC 7623 PBB-EVPN September 2015
[RFC7209] Sajassi, A., Aggarwal, R., Uttaro, J., Bitar, N.,
Henderickx, W., and A. Isaac, "Requirements for Ethernet
VPN (EVPN)", RFC 7209, DOI 10.17487/RFC7209, May 2014,
<http://www.rfc-editor.org/info/rfc7209>.
Acknowledgements
The authors would like to thank Jose Liste and Patrice Brissette for
their reviews and comments of this document. We would also like to
thank Giles Heron for several rounds of reviews and providing
valuable inputs to get this document ready for IESG submission.
Contributors
In addition to the authors listed, the following individuals also
contributed to this document.
Lizhong Jin, ZTE
Sami Boutros, Cisco
Dennis Cai, Cisco
Keyur Patel, Cisco
Sam Aldrin, Huawei
Himanshu Shah, Ciena
Jorge Rabadan, ALU
Sajassi, et al. Standards Track [Page 22]
RFC 7623 PBB-EVPN September 2015
Authors' Addresses
Ali Sajassi, editor
Cisco
170 West Tasman Drive
San Jose, CA 95134
United States
Email: sajassi@cisco.com
Samer Salam
Cisco
595 Burrard Street, Suite # 2123
Vancouver, BC V7X 1J1
Canada
Email: ssalam@cisco.com
Nabil Bitar
Verizon Communications
Email: nabil.n.bitar@verizon.com
Aldrin Isaac
Juniper
Email: aisaac@juniper.net
Wim Henderickx
Alcatel-Lucent
Email: wim.henderickx@alcatel-lucent.com
Sajassi, et al. Standards Track [Page 23]